CNC4PC C34AB User manual

USER’S
MANUAL
VER.1.1
C34AB BOARD Rev. 1
JANUARY, 2022

User’s Manual
Page i
USER'S MANUAL
TABLE OF CONTENTS
Page #
Contents
1.0 OVERVIEW.....................................................................................................................1
2.0 FEATURES.....................................................................................................................1
3.0 BOARD DESCRIPTION..................................................................................................1
4.0 JUMPER TO SELECT THE ENABLE.............................................................................2
5.0 JUMPER TO SELECT THE DIFFERENTIAL OUTPUT...................................................2
6.0 WIRING SAMPLE...........................................................................................................3
6.1 Diagram of connection with output signals not Differentials and C32.....................3
6.2 Diagram of connection with output signals Differentials, C74 and C32...................4
6.3 Diagram of connection with output signals not differentials and C62......................4
6.4 Diagram of connection with output signals Differential, C74 and C62.....................5
7.0 PINOUT...........................................................................................................................5
8.0 DIMENSION....................................................................................................................6

User’s Manual
Page 1
1.0 OVERVIEW
This interfaces board is used for the connection between C35, C32, C62 or C74 and the
ALLEN BRADLY ULTRA 3000 SERVO DRIVE.
2.0 FEATURES
•HDM44D connector for Connection of Driver.
•RJ45 Connector for Axis.
•Select Jumper for Hard Enable or Soft Enable.
•Select Jumper for signals Differentials
•Terminals for external power supply 5V and 24V
3.0 BOARD DESCRIPTION

User’s Manual
Page 2
4.0 JUMPER TO SELECT THE ENABLE
Use Software Enable to keep the driver active only while the system is active.
Set of jumper as shown in the image.
SOFT ENABLE
Use Hardware Enable to keep the driver enabled all the time.
Set of jumper as shown in the image.
HARD ENABLE
5.0 JUMPER TO SELECT THE DIFFERENTIAL OUTPUT
If working the outputs of STEP and DIR as differentials signals, you have to use the
board C74, set jumper as shown in the image.
DIFFERENTIAL

User’s Manual
Page 3
If not use the differential signal for outputs of STEP and DIR, set jumper as shown in the
image
NOT DIFFENTIAL
6.0 WIRING SAMPLE
6.1 Diagram of connection with output signals not Differentials and C32.

User’s Manual
Page 4
6.2 Diagram of connection with output signals Differentials, C74 and C32.
6.3 Diagram of connection with output signals not differentials and C62.

User’s Manual
Page 5
6.4 Diagram of connection with output signals Differential, C74 and C62.
Note: This wiring is just to illustrate a sample product application. Specific wiring may
vary from system to system. It is the user’s responsibility to implement it correctly.
7.0 PINOUT
ULTRA 3000 AC SERVO DRIVE AND C34AB CONNECTION
HDM44D PIN
FUNCTION
RJ45 PIN
2
COM-(5v)
4
3
EXT_5V+
NOT USED
4
STEP+
2
5
STEP-
NOT USED/ DIF 1
6
DIR+
6
7
DIR-
NOT USED/ DIF 3
27
COM-(24V)
NOT USED
29
24V
NOT USED
31
SERVO ON
NOT USED
39
ALARM
NOT USED
DIF = DIFFERENTIAL; When used signals Differentials, the pins of RJ45 are 1 and 3

User’s Manual
Page 6
8.0 DIMENSION
All dimensions are in Millimeters.
DISCLAIMER
Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC
nor Arturo Duncan are liable for any accidents resulting from the improper use of these
devices. This board is not a fail-safe device and it should not be used in life support
systems or in other devices where its failure or possible erratic operation could cause
property damage, bodily injury or loss of life.