ASI VELARE 0663-1 User manual

MODEL №:
ISSUED:
REVISED:
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
IMPORTANT: READ THESE INSTRUCTIONS COMPLETELY PRIOR TO BEGINNING
INSTALLATION & RETAIN FOR FUTURE REFERENCE WITH SUB-SYSTEM OM’S.
Open the mirrored door using the tumbler lock located at the bottom of unit in order to access the interior of the
module. Use caution when opening the door as the gas springs will raise the door from closed position. Remove
and retain the key for future access.
Pack contents:
1x 12V AC/DC Adapter with 1 output plug for Foam Soap Dispenser
1x 12V AC/DC Adapter with 2 output plugs for EL Lighting System
2x Mounting Hanging Brackets
INSTALLATION OF WALL MOUNTING HANGER HOOKS
Appropriate wall reinforcement and AC quad outlet must be prepared prior to initiating the Velare™ BTM
System installation (see Fig. 2 for blocking reference and Fig. 5 for Electrical KO location). Install the two (2)
wall mounting hanger hooks located in the interior of the module on wall using twelve (12) № 12 self-threading,
pan-head screws (by others) (Fig. 1) into appropriate wall reinforcements (Fig. 2). Hang the cabinet on wall
mounting hanger hooks (Fig. 3). Suggested mounting height is to position bottom of module 16" [406] to
20" [508] above vanity top (Fig. 4). Power can be provided to the interior of module through the Electrical
Service KO for Quad Outlets located at the back of the cabinet.
IMPORTANT: Install two (2) № 12 self-taping locking screws (by others) at the security locking holes to
prevent unit from being lifted off hanger hooks.
0663-1/2
29 JAN 2019
13 MAR 2019
VELARE™ BTM SYSTEM CABINET INSTALLATION GUIDE (PAGE 1 OF 3)
FIG. 1
FIG. 2
NOTES:
Dim's inch [mm] & NTS
See TDS for Dim's not shown

MODEL №:
ISSUED:
REVISED:
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
INSTALLATION OF EL-LIGHTING
Connect the two (2) output connector plugs of the 12V AC/DC Adapter with 2 Outputs (provided) into the two
(2) DC Power switches’ sockets (provided) located at the top of the cabinet.
Connect the 12V AC/DC Adapter (provided) to the Quad Outlet (by others).
Turn ON the two (2) DC switches (provided).
INSTALLATION OF HAND DRYER
Electrical service is supplied and connected by others. The power wiring should go through the KO located at the
Hand Dryer Bracket. Refer to 0196-OM for power wiring installation. Hand Dryer Cover can be removed by
removing the two (2) black plastic hole caps located at the bottom of the cabinet to access the cover security
screws with the security hex key provided with the 0196 dryer.
INSTALLATION OF FOAM SOAP DISPENSER
Foam Soap Dispenser includes power supply adapter (provided, item 1) to be connected into one of the quad
outlets (by others).
Soap Tank can be filled by removing the soap tank from soap tank holder bracket and unscrewing the cap.
Fill the tank with foaming soaps with a pH in range 7±1.5 and viscosity in range 1 ~ 100 cP (mPa•s).
Close the cap after filling and place the soap tank back to the soap tank holder bracket. Make sure the soap tube
reaches to approximately 1/4" [6] above the bottom of the soap tank through the guide sleeve and it is not bent or
curved.
Refer to OM provided with specific soap dispenser for maintenance instructions.
29 JAN 2019
13 MAR 2019
VELARE™ BTM SYSTEM CABINET INSTALLATION GUIDE (PAGE 2 OF 3)
FIG. 3
FIG. 4
0663-1/2

MODEL №:
ISSUED:
REVISED:
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
29 JAN 2019
13 MAR 2019
VELARE™ BTM SYSTEM CABINET INSTALLATION GUIDE (PAGE 3 OF 3)
FIG. 5
WIRING AND TUBING NOT SHOWN FOR ENHANCED CLARITY
0663-1/2