Coaster 900723 User manual

Fine Furniture for every stage of life
COASTERFURNITURE.COM
900723
Grandfather Clock
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
PAGE 1 OF 10
REVISION 3: 07/12/2022

Ⅻ
Ⅰ
Ⅱ
Ⅲ
Ⅱ
Ⅱ
Ⅴ
Ⅵ
Ⅶ
Ⅷ
Ⅸ
Ⅹ
Ⅺ
PARTS IDENTIFICATION
Your clock is fitted with a Westminster Chiming movement. This has an automatic night silence function that silences the
Chimes between 10.00 P.M. and 5.00 A.M.(last strike 9:00PM, first strike 6:00AM).
Before the clock leaves the factory, the clock has been set at 5:55AM.
Please make sure you have 2 x C and 3 x AA Alkaline batteries, as these are not included. You will also need a screwdriver.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
1PC
8PCS
QTYFIGUREDESCRIPTION DESCRIPTION QTYFIGURE
2PCS
BOLTφ8*40mm
FIXING BARS
Z
1
2
3
4
5
6
HARDWARE IDENTIFICATION
ASSEMBLY TIPS:
Warning!
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1. Don’t attempt to repair or modify patrs that are broken or defective. Please contact the store immediatelly.
2.This product is for home use only and not intended for commercial establishments.
PART NAME FIGURE QTY PART NAME FIGURE QTY
ATOP UNIT 1PCFBASE UNIT
1PC
GTOP
DECORATION
1PC
HPENDULUM
2PCS
IDECORATION
WEIGHTS
4PCS
JDECORATION
CHAINS
1PC
BFRONT DOOR
1PC
CLEFT SIDE
PANEL
1PC
DRIGHT SIDE
PANEL
1PC
EBACK PANEL
CABLE TIE
LONG SCREW
SHORT SCREW
PLASTIC ANCHOR
1PC 1PC
1PC
1PC
ITEM:900723
SIZE AA
SIZE C
2 PCS 3 PCS
ALKALINE BATTERIES REQUIRED ASSEMBLY TOOLS REQUIRED
COASTERFURNITURE.COM
ASSEMBLY TIME PER UNIT: 20 MINUTES BY 2 PERSONS
PAGE 2 OF 10

NOTES: PLEASE MAKE SURE CLOCK IS IN LEVEL POSITION, OTHERWISE
IT WILL NOT OPERATE PROPERLY.
STEP 1-1 STEP 1-2
STEP 2-1 STEP 2-2
STEP 3
①
C
F
F
C
D
C
F
①
①
F
C
D
C
D
E
E
ITEM:900723
COASTERFURNITURE.COM
PAGE 3 OF 10

STEP 4-1 STEP 4-2
STEP 5
STEP 6
G
A
C
①
①
A
①
A
D
①
A
D
C
ITEM:900723
COASTERFURNITURE.COM
PAGE 4 OF 10

Ⅻ
Ⅰ
Ⅱ
Ⅲ
Ⅱ
Ⅱ
Ⅴ
Ⅵ
Ⅶ
Ⅷ
Ⅸ
Ⅹ
Ⅺ
STEP 7-1 STEP 7-2
STEP 8
STEP 9
ｈｏｌｅ
ｈｏｏｋ
J
short chain
long chain
weight
pendulum H
J
I
H
②
B
D
ITEM:900723
COASTERFURNITURE.COM
√
×
PAGE 5 OF 10

BACK OF THE CLOCK
ATTENTION: ANTI TIPPING SAFEGUARD
STEP 10
WALL
⑥④
③
1.Insert 2 x C Batteries into the Pendulum Battery
Chamber.Ensure that the positive and negative
symbols are aligned as shown.
2.Push Pendulum Hanger lightly,to release the
Pendulum Hanger from "Pendulum Hanger Shipping
Retainer", and to allow Pendulum to swing freely.
3. Hang the Pendulum (H) as shown in the figure
below.Make sure that the bright side of the Pendulum
Bob fces te front of the clock.
4. Hang the Decorative Weight (I) as in the figure
below.
5. Lightly push the Pendulum (H) sideways to let it
swing.
IMPORTANT NOTICE: PLEASE MAKE SURE THE
PENDULUM HANGER" IS RELEASED FROM THE
"PENDULUM HANGER SHIPPING RETAINER",
OTHERWISE THE PENDULUM WILL NOT SWING.
Ｐｅｎｄｕｌｕｍ
Ｓｅｃｔｉｏｎ
Pendulum Hanger
Pendulum Battery Chamber
Pendulum Hanger Shipping
Retainer(Push to release Pendulum)
ＳＩＺＥ Ｃ
ＳＩＺＥ Ｃ
PENDULUM INSTRUCTION
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint is not a substitute for proper adult supervision.
This restraint may provide protection against tipping furniture.
Do not allow children to climb on furmiture.
Failure to detach this restraint before moving furniture may
result in injury and damage.
④
⑤
③
ITEM:900723
PAGE 6 OF 10
COASTERFURNITURE.COM

Chime Battery
Chamber
Switch
Volume
Control
Red“Set”
button
chime
section
FIGURE 2
ＳＩＺＥ ＡＡ
ＳＩＺＥ ＡＡ
ＳＥＴ
Before setting time, chime and pendulum, please open the
back panel on the Top Unit. Aer removing the cover,
please refer to the figure at the right to identify and locate
the following items:
■ Clock Section
■ Clock Battery Chamber
■ Chime Section
■ Chime Battery Chamber
■ Pendulum Section
■ Pendulum Battery Chamber
1. if it is not at 5:55, turn clock hands to 5:55 by Hand Set Knob(Figure 1).
Make sure the hands move CLOCKWISE ONLY.
2. Insert 2 x AA Batteries as shown (Figure 2). Ensure that the positive
(+) and negative (-) symbols are aligned as shown.
3. Insert 1 x AA Battery into the
Clock Battery Chamber (Figure
1).Ensure the positive (+) and
negative (-) symbols are aligned as
shown.
4. Press the Red 'Set' Button once
to start the chiming sequence.
5. Your clock will play the 'Westminster' chime and 'strike' six
times indicating 6:00am.Your clock is now set to the correct
chiming sequence 3 (Figure 2).
6. Aer setting the correct chiming sequence,then set the clock to
the correct time with the Hand Set Knob.
E.g.-if you are setting the clock to 8 o'clock in the evening,8:00 pm,you will need to move the hands
forward to 12 o'clock and then continue to 8 o'clock to show 8:00 pm. Alternatively, if the time is 8:00
am when you are setting,you just move the hands forward from 8:00 to 8:00. The clock now knows it
is 8:00 am.
If the clock time is not right or the clock chimes incorrectly,please replace the batteries,and follow
the set time and chime procedure as above.
Your clock will not chime or strike aer 9:00 pm,It has an AUTOMATIC night mute with the last strike
at 9:00 pm and the first at 6:00 am.
SETTING INSTRUCTIONS
Clock Battery
Chamber
Hand Set
Knob
Clock
Section
ＳＩＺＥ ＡＡ
QUARTZ
FIGURE 1
Ｐｅｎｄｕｌｕｍ
Ｓｅｃｔｉｏｎ
Clock Battery
Chamber
Ｃｌｏｃｋ
Ｓｅｃｔｉｏｎ
ｓｐｅａｋｅｒ
ｓｅｃｔｉｏｎ
ＳＩＺＥ ＡＡ
ＱＵＡＲＴＺ
Chime Battery
Chamber
ｃｈｉｍｅ
ｓｅｃｔｉｏｎ
ＳＩＺＥ ＡＡ
ＳＩＺＥ ＡＡ
ＳＥＴ
ＳＩＺＥ Ｃ
ＳＩＺＥ Ｃ
SETTING TIME AND CHIME
1 2 3 4
1 2 3 4
ITEM:900723
PAGE 7 OF 10
COASTERFURNITURE.COM

TROUBLESHOOTING
Here are a few symptoms that are associated with 'Defective Batteries' or 'Incorrect Installation'
and do not indicate that the clock itself is defective:
If the positive and negative poles of any battery are reversed, they must be removed first and then
installed again. All are taken down to initialize the clock. Then install it correctly. It is not possible
to mix an old battery with a new battery, let alone replace it with another type of battery. Be sure
to use 3pcs of AA size and 2pcs of C size batteries. A bad battery can also cause the clock to work
infrequently.
Possible conditions of the clock caused by insufficient battery power: Inaccurate time reporting,
random time reporting, always reporting one time. Or the volume of timekeeping and music is
getting weaker and weaker. If the battery is low, it will leak, and corrode the metal circuit and cause
the clock to malfunction. Even damage the battery box. If any of the above problems are found,
replace the battery in time.
Regarding the operating troubleshooting methods:
1. When you assemble the clock, you should be careful to avoid touching the pointer and each line
to prevent the clock hands from shiing and the line loose.
2. (Figure 1) When turn the clock hands by Hand Set Knob counterclockwise, Do not let minute
hand past the 12 o'clock position, otherwise it will damage the timekeeping contacts of the
movement, resulting in failures such as no timekeeping or no music.)
3. Before the clock leaves the factory, the hour hands have been set at 5:55AM. If the clock display
is not this time, please turn the minute hand by Hand Set Knob clockwise to adjust to 5:55AM,
and then insert the battery.
4. The first chime is set to 6:00 AM. The chime will stop automatically from 10:00 PM to 5:00 AM.
(The night stop function is programmed before leaving the factory. The user cannot change it)
5. Once the battery is removed, the chime box will be automatically initialized. Aer reloading, it
will be reported again from 6:00 in the morning. (Figure 2)
CAUTION
Do not mix Old and New batteries. Do not mix Alkaline, and Standard(Carbon - Zinc) or
Rechargeable(Nickel - Cadmium) batteries.
ITEM:900723
COASTERFURNITURE.COM
PAGE 8 OF 10

Regarding the timekeeping troubleshooting methods:
1.Solution for not reporting the time with chime:
a.Rotate the volume button (Figure 2) to the maximum position.
b.Check whether the positive and negative positions of the battery are correct (Figure 2). If it
is inaccurate, please reinstall it according to the icon.
c.If the positive and negative poles of the battery are correct and the problem is still not
resolved, adjust the time to 5:55 clockwise by Hand Set Knob, remove the battery, wait for
a while, and place it again. Then adjust the clock hands to 6:00 to tell the time and music.
d.Or use the Red button on the Chime box (Figure 2) to solve problem as (c.) above, each time
you press, no more than 8 times, you can hear the time and music. The time signaling this
time is 6:00 AM. And then, press the red button to match the clock time. Aer that turn
Hand Set Knob to adjust the clock hands clockwise to the actual local time.
2.The clock telling time is inconsistent with the displayed time. It can be adjusted by the Red
button (Figure 2) on the Chime box. Each time you press it, an hour will be added, and so on.
Note that the Red key is aer 12 o'clock, and it is 1:00 when you press it again.
3.The hourly timekeeping time is inconsistent with the displayed time. Please set the clock to
5:55 without placing the battery (Figure 1). Aer placing the battery, manually automatically
go to 6:00, and the clock will show time as 6:00 AM.
4.The time is not reported at 10 o'clock during the day, but reported 10 o'clock at night. The
main reason is that the clock defaults to night as day. You can press the Red (Figure 2) button
on the Chime box for 12 times to change the time from day to night.
5.If the clock reported with other chime or strike only or 'Westminster' chime only in full hours,
please set the correct chiming sequence 3. See picture 2 at PAGE 7.
Regarding pendulum troubleshooting methods:
1.If the swing range of the rocker is small or does not swing, the general situation is that the
battery power is insufficient, or the connection line between the rocker and the battery box
is poor, and you need to replace new batteries or reinsert it and confirm whether it is secure.
2.If the swing range of the pendulum is unstable, or it shakes, etc. In addition to the battery
power attenuation, it is usually caused by the hook of the pendulum not hanging to the
middle position of the pendulum rod. See (The 3 sentence of paragraph 1), and make sure
that the pendulum plate and the clock body are parallel. Don't deviate, twist, etc. and you
need to manually push the pendulum plate to the le or right, so that the pendulum plate
does not touch the inner wall of the clock case. The pendulum will swing normally.
ITEM:900723
PAGE 9 OF 10
COASTERFURNITURE.COM

PAGE 10 OF 10
ITEM:900723
COASTERFURNITURE.COM