Coaster 204190Q Installation guide

R
www.coastercompany.com
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
FINE FURNITURE
204190Q (B1 ~ B4)
QUEEN SIZE STORAGE BED
PAGE 1 OF 4 REVISION 0 : 04/08/2016
REVISION 1 : 11/14/2016

HARDWARE IDENTIFICATION
Z - B1 (BOX 1) - HARDWARE PACK IS
LOCATED IN 204190Q (B1)
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
Warning !
1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishment.
ASSEMBLY TIME
HB
Z - B2 (BOX 2) - HARDWARE PACK IS
LOCATED IN 204190Q (B2)
D
204190Q (B1)
HEADBOARD COMPLETE
* FROM BOX 1
204190Q (B1)
FOOTBOARD
* FROM BOX 1
1PC
1PC
PARTS IDENTIFICATION
HEADBOARD PANEL 1PC
1PC
1PC
1PC
NOTE : PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY
PROCESS; HOWEVER MANUFACTURER DOES NOT PROVIDE THIS ITEM.
B1 (BOX 1)
A
B
D
C
B2 (BOX 2)
E
G
I
K
L
M
LEFT HEADBOARD LEG
RIGHT HEADBOARD LEG
FOOTBOARD
BED SLAT WITH 3 HOLES 3PCS
ROLL SLAT (5PCS) 2SETS
CENTER RAIL SUPPORT
WITH LEVELER
3PCS
STORAGE FOOTBOARD
SUPPORT LEG
2PCS
RIGHT BED RAIL
1PC
F
LEFT BED RAIL
1PC
BOLT
1
LOCK WASHER
2
FLAT WASHER
3
ALLEN WRENCH
4
6PCS
6PCS
6PCS
1PC
www.coastercompany.com
FINE FURNITURE
R
B3 (BOX 3)
DRAWER BOX
N2PCS
B4 (BOX 4)
DRAWER BOX
O2PCS
HDRAWER SLAT 2PCS
30 MINUTES
ASSEMBLY INSTRUCTIONSITEM : 204190Q (B1 ~ B4)
PAGE 2 OF 4
J
8
4PCS
55PCS
1PC
91PC
7
43PCS
6
SHORT FLAT HEAD SCREW
LONG BOLT
SMALL ALLEN WRENCH
LONG FLAT HEAD SCREW
BIG ALLEN WRENCH
BOTTOM CROSS BAR 3PCS
CENTER RAIL 1PC

STEP 2
HB
F
D
E
204190Q (B1) - BOX 1
STEP 1
204190Q (B1 & B2) - BOX 1 & BOX 2
STEP 2.3
6
H
STEP 3
204190Q (B1 & B2) - BOX 1 & BOX 2
STEP 3.2
6
M
F
ASSEMBLY INSTRUCTIONSITEM : 204190Q (B1 ~ B4)
www.coastercompany.com
FINE FURNITURE
RPAGE 3 OF 4
9
STEP 2.1
STEP 2.2
A
C
B
Headboard & Leg
"R" Marking behind the
B
"L" Marking behind the
Headboard & Leg
**Please take note the marking on the leg and headboard**
8
J
5
H
STEP 3.1
4
1
2
3

N
STEP 4
204190Q (B1 ~ B4) - BOX 1 TO BOX 4
J
H
STEP 5
N
O
O
STEP 4.1
STEP 4.3
J
J
5
L
K
G
STEP 5.1
8
K
STEP 5.2
K
M6
NOTE : ( for STEP 4.2 )
i) Fully insert the drawer box (N,O) until touch
to the black frame.
ii) Screw the T-Runner to the drawer slat (H).
Leveler
N O
/
N O
/
Leveler
ASSEMBLY INSTRUCTIONSITEM : 204190Q (B1 ~ B4)
www.coastercompany.com
FINE FURNITURE
RPAGE 4 OF 4
6
I
STEP 5.3
'T' Runner
STEP 4.2
H
7
F