Coaster 460441 B1-B4 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
460441
(B1
-
B4)
Twin/Twin Bunk Bed
REVISION 0 : 11/28/2012
REVISION 1 : 01/21/2013
REVISION 2 : 11/07/2013
REVISION 3 : 01/21/2016
REVISION 4 : 05/16/2019 PAGE 1 OF 7
REVISION 5 : 07/05/2019
COASTERFURNITURE.COM

ITEM:460441 (B1-B4)
ASSEMBLY TIME
ALEFT
BED END 1PC
ROLL SLAT
(13PCS) 2SETS
BMIDDLE
BED END 1PC
ITOP LADDER
STEP 1PC
DGUARDRAIL 4PCS
K
MIDDLE
LADDER STEP
WITH DRAWER
1PC
EBED RAIL
WITH HOLE 2PCS
L
BOTTOM
LADDER STEP
WITH DRAWER
1PC
FBED RAIL
WITHOUT HOLE 2PCS
H
BOTTOM RAIL
WITH DRAWER 1PC
GFLAT GUARDRAIL
SUPPORT 4PCS
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
PARTS IDENTIFICATION
30 MINUTES
PAGE 2 OF 7
RIGHT
BED END
C1PC
BACK RAIL
J4PCS
B1 ( BOX 1)
B2 ( BOX 2)
B3 ( BOX 3 )
B4 ( BOX 4)
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2.
This product is for home use only and not intended for commercial establishments.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
COASTERFURNITURE.COM
M

HARDWARE IDENTIFICATION
Z-B2 (BOX 2) - HARDWARE PACK IS LOCATED IN 460441 (B2)
1 LONG BOLT 32PCS 5 SHORT BOLT 16PCS
2BARREL NUT 32PCS 6 LONG FLAT HEAD 16PCS
3 WOOD DOWEL 36PCS 7 ALLEN WRENCH 1PC
4MEDIUM BOLT 20PCS 8 SHORT FLAT HEAD
SCREW 24PCS
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
PAGE 3 OF 7
(1/4 x 30mm - BLK)
(1/4 x 13mm - BLK)
(10 x 40mm )
(1/4 x 35mm - BLK)
(4 x 30mm - BLK)
(3 x 10mm - BLK)
(1/4 x 90mm - BLK)
(4MM - BLK)
ITEM:460441 (B1-B4)
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2.
This product is for home use only and not intended for commercial establishments.
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
COASTERFURNITURE.COM
SCREW

ASSEMBLY INSTRUCTIONS
STEP 1
STEP 3
PAGE 4 OF 7
AJ
B
1
7
A2
3J
KL
&
8
STEP 2
M
8
STEP 4
AJ
4
44
4
4
4
4
7
I
K
L
M34
ITEM:460441 (B1-B4)
COASTERFURNITURE.COM
4:1
4:4
4:3
4:2

ITEM:460441 (B1-B4)
ASSEMBLY INSTRUCTIONS
STEP 5
STEP 7
COASTERFURNITURE.COM
PAGE 5OF 7
DG
7
5E5
D
G
E
G
3
E
C
F
F3
2
STEP 6
STEP 8
COMPLETE
G
6:1 7
1
2
ABD
D
E
17
6:2
6666
H
H

ITEM:460441 (B1-B4)
ASSEMBLY INSTRUCTIONS
The length and width of the bunk mattress are as follow:
Upper bunk 37 1/2"- 38 1/2" 6" Maximum
Lower bunk 6" Maximum
1.
2.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8.
Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11.
12. The use of water or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD:
14.
REPLACEMENT PARTS:
Always use the recommended size mattress or mattress support or both to help prevent
the likelihood of entrapment or falls.
Periodically check and ensure that the guardrail, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
Never attach or hang items to any part of the bunk bed that are not designed for use with
the bed for example, but not limited to hooks, belts, and jump ropes.
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
PAGE 6 OF 7COASTERFURNITURE.COM
74" -75"
Ensure thickness of mattress does not exceed 6” and there must be at least 5” from mattress
sleeping surface to top edge of guardrail.
SAFETY WARNING
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove the warning label from bed.
Width
SIZE OF MATTRESS
Length
74" -75" Thickness
37 1/2"- 38 1/2"

ITEM:460441 (B1-B4)
ASSEMBLY INSTRUCTIONS
1.
2.
3.
4.
5.
Any misuse or unauthorized use of the ladder could result in serious or fatal injury.
Failure to follow the above WARNING, and/or failure to follow assembly instructions
completely, will void any and all liability of COASTER COMPANY OF AMERICA for
damages and injury to persons and property.
PAGE 7 OF 7 COASTERFURNITURE.COM
When using beds as bunk beds, the ladder MUST be securely attached to the upper bunk
rail at all times.
When using the beds as two (2) separate floor-standing beds, the ladder MUST be stored
in a separate location where children cannot use the ladder in any manner.
DO NOT use, nor permit children to use, the ladder in any manner whatsoever, other than
to access the top unit when used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
WARNING
TO PREVENT SERIOUS OR FATAL INJURY
Coasterfurniture.com | 877-COASTER (262-7837)