Coaster 460563T User manual

Fine Furniture for every stage of life
460563T
COASTERFURNITURE.COM
PAGE 1 OF 9
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
d
REVISION 0 : 10/13/2023
Twin/ Twin Bunk Be

PAGE 2 OF 9 COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIME 30 MINUTES
PARTS IDENTIFICATION
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
ASSEMBLY TIPS:
WARNING!
1.Don’t attempt to repair or modify parts that are broken or defective. Please contact the store immediately.
2.This product is for home use only and not intended for commercial establishments.
ITEM: 460563T
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
A1PC
K2PCS
B2PCS
L
C1PC
M1PC
D4PCS
N1PC
FRONT GUARD RAIL
LONG GUARDRAIL
(BACK)
SHORT GUARDRAIL
(FRONT)
FRONT UPPER
SIDE RAIL
BACK UPPER
SIDE RAIL
FRONT/ BACK
LOWER SIDE RAIL
E8PCS
F1PC
G1PC
H2PCS
I2PCS
J2PCS
O4PCS
P2SETS
ROLL SLAT (14PCS)
LADDER STEP
RIGHT LADDER
RAIL
LEFT LADDER
RAIL
1PC
CENTER GUARD RAIL
SUPPORT
LEFT
BACK POST
LEFT
FRONT POST
RIGHT
FRONT POST
UPPER GUARDRAIL
HEADBOARD
CENTER & LOWER
GUARDRAIL HEADBOARD
SUPPORT

PAGE 3 OF 9 COASTERFURNITURE.COM
HARDWARE IDENTIFICATION
1
2
3
16PCS
24PCS
6
78PCS
9
4
10PCS 8
5
16PCS
LONG BOLT
(Φ1/4x 80MM - WHT)
HEX HEAD SCREW
(Φ5/16x 80MM - WHT)
MEDIUM BOLT
(Φ1/4x 40MM - WHT)
LONG FLAT HEAD
SCREW
(4 x 35MM - WHT)
20PCS
4PCS
SHORT FLAT HEAD
SCREW
(4 x 20MM - WHT)
THREADED INSERT
(Φ1/4x 25MM - WHT)
WOOD DOWEL
(10 x 30MM)
ALLEN WRENCH
(4 x 78MM - WHT)
2PCS
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
ITEM: 460563T
6PCS
SHORT BOLT
(Φ1/4x 25MM - WHT)
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1.Don’t attempt to repair or modify parts that are broken or defective. Please contact the store immediately.
2.This product is for home use only and not intended for commercial establishments.
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.

PAGE 4 OF 9 COASTERFURNITURE.COM
STEP 1
9
2
D
E
E
A
E
D
E
B
STEP 2
D
E
D
E
B
C
E
E
9
2
ASSEMBLY INSTRUCTIONS
ITEM: 460563T

PAGE 5 OF 9 COASTERFURNITURE.COM
STEP 3
STEP 4
9
1
2
9
1
8I
G
J
FH
H
L
9
3
7
8
9
2
3.1
3.2
4.1
4.2
ASSEMBLY INSTRUCTIONS
ITEM: 460563T

PAGE 6 OF 9 COASTERFURNITURE.COM
STEP 5
STEP 6
9
M
N
O
9
7
5
K
6.1
3
66.2
ASSEMBLY INSTRUCTIONS
ITEM: 460563T

PAGE 7 OF 9 COASTERFURNITURE.COM
STEP 7 P
4
STEP 7
COMPLETE
P
P
ASSEMBLY INSTRUCTIONS
ITEM: 460563T

The length and width of the bunk mattress are as follow:
Upper bunk 37 1/2"- 38 1/2" 6" Maximum
Lower bunk 6" Maximum
1.
2.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8.
Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11.
12. The use of water or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD:
14.
REPLACEMENT PARTS:
Always use the recommended size mattress or mattress support or both to help prevent
the likelihood of entrapment or falls.
Periodically check and ensure that the guardrail, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
Never attach or hang items to any part of the bunk bed that are not designed for use with
the bed for example, but not limited to hooks, belts, and jump ropes.
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
74" -75"
Ensure thickness of mattress does not exceed 6” and there must be at least 5” from mattress
sleeping surface to top edge of guardrail.
SAFETY WARNING
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove the warning label from bed.
Width
SIZE OF MATTRESS
Length
74" -75" Thickness
37 1/2"- 38 1/2"
PAGE 8 OF 9COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
ITEM: 460563T

1.
2.
3.
4.
5.
Any misuse or unauthorized use of the ladder could result in serious or fatal injury.
Failure to follow the above WARNING, and/or failure to follow assembly instructions
completely, will void any and all liability of COASTER COMPANY OF AMERICA for
damages and injury to persons and property.
OF 9COASTERFURNITURE.COM
When using beds as bunk beds, the ladder MUST be securely attached to the upper bunk
rail at all times.
When using the beds as two (2) separate floor-standing beds, the ladder MUST be stored
in a separate location where children cannot use the ladder in any manner.
DO NOT use, nor permit children to use, the ladder in any manner whatsoever, other than
to access the top unit when used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
WARNING
TO PREVENT SERIOUS OR FATAL INJURY
Coasterfurniture.com | 877-COASTER (262-7837)
PAGE 9
ASSEMBLY INSTRUCTIONS
ITEM:460563T

COASTERFURNITURE.COM
Inner Size : 75.00"W x 39.00"D
77.50"
58.25"
30.00"
15.00"
20.50"
15.00"
37.50"
63.00"
15.00"
ITEM: 460563T
11.75"
13.50"
8.25"
30.00"
Note: Dimension tolerance ±5%
9.75"
75.00"
42.75"
42.75"