COBHAM Saailor Fleet One User manual

What’s in the box?
Dimensions for the SAILOR Fleet One antenna
Drilling plan for the SAILOR Fleet One terminal
The following items are included in the delivery:
• SAILOR Fleet One terminal
• SAILOR Fleet One antenna
• DC power cable (1 m) for the terminal
• Ethernet cable (2 m)
• I/O connector
• Mounting bolts and washers for the antenna
• RF cable (10 m)
• Kit for water protection of antenna connector joint
• Installation guide (this guide)
• Quick guide
• CD with User & installation manual, Installation guide and Quick guide
SAILOR Fleet One
Installation guide
Important notes for placing the antenna
• When mounting the antenna, make sure you do not block the drainage hole
in the centre bottom of the antenna.
• Leave space under the antenna for the antenna cable and connector
• Make sure the antenna has a free view to as much of the sky as possible.
Installing the SAILOR Fleet One System
1. Mount the antenna on a mast or on the hull using the enclosed mounting bolts.
Use the mounting bolts for grounding the antenna to the same ground as the
terminal.
• To mount the antenna on a mast, use the mast mount kit available from
CobhamSATCOM.Themastmountkittsa1½”pipe(OD48.3mm).
Instructions are included with the kit.
• To mount the antenna on the hull, use M6 mounting bolts and mount
spacers to avoid blocking the drainage hole in the bottom of the antenna.
The bolts must go 6 to 12 mm into the bushings in the radome. Fasten with
7to8Nmtorque.
2. Mounttheterminalindoorsonaatmountingsurface,e.g.onabulkheador
desktop, using four M5 screws of a type suitable for the mounting surface.
If the mounting surface is used for grounding, make sure that you have a good
electrical connection between the mounting surface and the terminal chassis.
Note: If you want to use the cable relief from Cobham SATCOM (Spare part no.
S-673738A)fortheterminal,rstremovethetworubberfeetattheconnector
endoftheterminal.ThenmountthecablereliefintheirplaceusingtwoM4x6
mm countersunk screws.
3. Connectthecablesasshowninthesystemcongurationdrawing(overleaf).
Power cable Use the power cable supplied with the SAILOR Fleet One
System. Connect the other end of the power cable to the
ship power supply . For wire colours in the power cable
see Connectors, pin allocation and wire colours (overleaf).
RF cable (antenna
cable)
Use the RF cable supplied with the SAILOR Fleet One System to
connect the antenna to the terminal. Seal the connection at the
antenna end using the enclosed kit for water protection.
4. If you are using a cable relief, secure the cables to the cable relief, e.g. using
cable strips.
Installation instructions
Cable relief (optional):
Remove the two rubber feet and mount the cable relief here.
Note: The drawings in this document are not drawn to scale. Refer to the dimensions written in the
drawing. All dimensions are in millimeters.
Note: The drawings in this document are not drawn to scale. Refer to the dimensions written in the
drawing. All dimensions are in millimeters.
Mastmountkit(partno.S-683742A-920)isnot
included, but is available from Cobham SATCOM.

Technical specications
98-141370-A
www.cobham.com/satcom
System conguration - example
Item Specication
Antenna weight 3.94kg(8.7lbs)
Antenna dimensions 291.9mmxØ275.6mm(11.5”xØ10.9”)
Terminal weight 2.2kg(4.9lbs)
Terminal dimensions 231mmx278mmx41m(9.1”x10.9”x1.6”)
Safety distance to antenna 0.6m(23.7”)
Power input for terminal Nominal12-24VDC(10.5-32VDC;11.5A-4A)
Ambient temperature Operational: -25° to +55 °C
Relative humidity
Antenna
Terminal
100% condensing
95%non-condensingat+40°C
To verify the successful installation of the SAILOR Fleet One System, do the following:
1. Insert your SAILOR Fleet One SIM card into the SIM slot (see the picture to the
left)
2. Switch on the terminal using the on/off button.
3. VerifythatthePowerindicatorontheterminallightsgreen.
4. ConnectacomputertooneoftheLANconnectors.
5. Open your browser and type in the IP address of the web interface (default
192.168.0.1)toaccessthebuilt-inwebinterface.
6. TheStatuseldinthewebinterfaceshowstheprogress(Scanning-Searching-
Registering - Ready).
7. WaituntiltheStatuseldshowsReady.
8. Connect your phone or computer and verify that you can make a call or con-
nect to the Internet.
For details on installation and use of your SAILOR Fleet One, see the SAILOR Fleet One
User & installation manual.
Verifying the installation
Power LED status Description
Off Unit is off
On, green Unit is on, normal operation
Flash pattern, green Starting up
Flash pattern, orange Shutting down
I/O connector
Pin Intended use
1 Ringer output
2 Warning/error output
3Indicator for data connection, output
4Control data connection on/off, input
5 Ignition input
6ChassisGND
7DCout,9-15VDC,50mA
8DC in (Ignition input)
Connectors, pin allocation and wire colours
81
Power cable wires
Wire colour Signal
Red (thick) Vin+
Black (thick) Vin-
Black (thin) Notconnected
Green Remote on/off
Brown Notconnected
Red (thin) Notconnected
Orange Remote on/off
SAILOR Fleet One antenna
SAILOR Fleet One terminal
Number Cable Description
1 Antenna cable Supplied with SAILOR Fleet One
2 Phone cable Notsupplied:StandardphonecablewithRJ-11connector.
3Ethernet cable Supplied with SAILOR Fleet One
4Power cable Supplied with SAILOR Fleet One
5 I/O cable Notsupplied
6 Ground cable for
Ground stud
Notsupplied:CableforconnectingtheGroundstudtoship
ground. Heavy wire or braid cable with a larger diameter
than the antenna cable.
Allow free space for
ventilation and cable
SIM card
Disclaimer: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed
by Thrane & Thrane A/S. The information in this manual is provided for information purposes only, is subject to change without notice and may contain
errors or inaccuracies. The manuals areperiodicallyrevisedandupdated.Anyonerelyingonthisinformationshouldacquirethemostcurrentversione.g.
from cobham.com/satcom or from the distributor. Thrane & Thrane A/S is not responsible for the content or accuracy of any translations or reproductions,
in whole or in part, of this manual from any other source. Thrane & Thrane A/S trading as Cobham SATCOM.
Copyright©2013Thrane&ThraneA/S.Allrightsreserved.