Cobra qms 180 User manual

Rein fo rc ed Anti-Invasion Door Defense
QMS 180
Q u a d - M o t i o n - S e n s o r
Dual Sensor Technology
For RAIDD System
COBRATM
FACTS INTERNATIONAL LTD
Nanjing, China, 211100
Patents Pending
www.factsintl.com
[e-mail]
Copyright 2012 FACTS Intl Ltd.
Reinforced
Anti-
Invasion
Door
DefenseTM
DESIGNED EXCLUSIVELY
FOR USE WITH
TM
Ready
COBRA QMS 180
US ER MA NUA L
1
Coverage
Top Sensor View
Coverage Side View
QMS 180
Q u a d - M o t i o n - S e n s o r
180 Degree View Area
Dual Sensor Technology
3 Passive Infrared (PIR)
1 Microwave (MW)
COBRATM
FACTS INTERNATIONAL LTD
PIR 3
PIR 1
PIR 2
MW
FULL 180 DEGREE
COVERAGE
10 m
30+ Ft
COBRA
QMS180
RAIDD
Protected
Door
Ready
Certified Certified
International Management Systems Certified:
ISO 9001:2008, ISO 14001:2004 and
OHSAS 18001:2007
Product Model Details
Model: COBRA QMS180
12 volt / Rated 5 amp DC
Rated: Continuous Operation
Normal Switch Configuration: N/O
“Smart Bus” Compatible
Ported: 1 Extra Zone Port - N/O
Wireless Valley Technology Park, Nanjing, China
WEBSITE: www.factsintl.com EMAIL: [email protected]
Facility Access Control Technology SystemsFACTS INTERNATIONAL, LTD TM
The Cobra QMS 180 is designed to be an "INSTANT ON" device with no "false alarm
circuitry" to delay the senor activation. The QMS180 "sees" in a 180 degree semi-circle
around the front surfaces of the sensor. This leaves no blind spots for an intruder to
approach the protected doorway. Place QMS180 above RAIDD protected Doorway.
The Cobra QMS180
was designed by the
Smart Home Group,
Changping, China, and
is Exclusively
Manufactured for
FACTS Int'l Ltd by
the Smart Home Group
for use with the
RAIDD System.
Cobra QMS 180, RAIDD,
Facility Access Control
Technology Systems,
and are Trademarks
of FACTS Int'l ,Ltd.
All Rights Reserved.
Copyright 2012
4

GND D- D+ VDC NCNO COM COM ON GND Z1
+9~24
Dry Contract Input
For Shock Sensor
Relay
Alarm Output Tamper
3
Power supply is
12 VDC to DC24V.
Do not connect the
QMS180 to any other
voltage. Unit works on
a maximum of 5 amps.
CONTROL CONTACTS:
INSTALLATION PROTOCOL
Connections
1st Connector Group (4 Wire Inserts):
1. +24V / 2. D+ / 3. D- / 4. GND: S-BUS connection,
2nd Connector Group (3 Wire Inserts):
1. N-C / 2. COM / 3. N-O:
DC30V 2A output, this is for integrating 3rd party product.
If it's NC, use 2 wires to connect NC, COM if it's NO, use 2 wires
to connect NO, COM . When the status of Any sensor is movement,
this relay will be on. When it's no movement, this relay will be off.
3rd Connector Group (2 Wire Inserts)
1. TAMPER Relay: DC30V 2A output. This relay will be on if the Plastic Housing is opened, and this
relay will be off if the Plastic Housing is closed. This relay can be connected siren for alarm. works
DC30V or less than DC30V.
4th Connector Group (2 Wire inserts)
1. Z1: this is an additional dry connect Input contact port, this can be connected to a Shock Sensor,
a exterior Pressure Contact or other exterior Motion (i.e. Laser Interference) and causes
activation of the RAIDD (same as QMS180).
FRONT VIEW
REAR VIEW
BOTTOM VIEW
TOP VIEW
SIDE VIEW
COBRA QMS 180
A AA
F
B
F
A AD
F
E E
D
D
F
A
A
A
B
D
C
B
2
The QMS 180
Quad-Motion Sensor
With 180 Degree
motion sensing -
utilizes Dual Sensor
Technology: 1 MicroWave
Detector (Forward wide
field view) and 3 Passive
Infrared (PIR) Sensors that
overlap their detection fields
to create a 180 degree "semi-
circle" around the QMS180.
This dual and overlapping
system provides full and
"Instant On" activation of the
RAIDD Door Defense System
at the 1st sign of any intruder
within the protected sensor
zone.
[A] PIR Sensors (Passive Infrared)
[B]
[C] Control Contacts
[D] Rear Panel
[E] Mounting Holes (in Rear Panel)
[F] Bottom Locking Screw
[G] Cable Run
[H] Microwave Sensor (Not Visible)
UV Resistant Housing
G
HE E
C
F
GD