Code Alarm ca5553sst User manual

CCCJc:~lA~m
r:»~OFESSIONAI
SE~IES
Automatic
I Manual Transmission
Remote Start
with
Keyless
Entry
Installation Guide
for
models:
ca5553sst
2012 Audiovox Electronics Corporation.
All
rights reserved. 4280478

Table
of
Contents
Before
You
Begin
......................................................................................3
Wire
Connection
Guide
...........................................................................4
11
Pin Main Harness .................................................................................5
3 Pin Parking Light Harness .....................................................................8
6 Pin Start Harness ...................................................................................9
4 Pin Alternate Harness .......................................................................... 10
2 Pin Door Lock Harness ........................................................................
11
Add
it
ion
aI
Ports
......................................................................................15
Antenna I LED I Programming Port ....................................................... 15
DBIPort....................................................................................................15
Telematic Interface Port .......................................................................... 15
Set
Up
&
Programming
..........................................................................16
Transmitter Programming ........................................................................ 16
Manual Feature Programming ................................................................. 16
Programming Feature Banks .................................................................. 17
Tach Programming .................................................................................. 19
Smart Tachless Mode ............................................................................. 19
Feature
Descriptions
.............................................................................20
Transmitter
Button
Functions
.............................................................26
Remote
Start
Shutdown
Diagnostics
................................................27
System
Layout
.........................................................................................28
2 ca5553sst rev A

•
....
BEFORE YOU BEGIN
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Roll down window to avoid locking keys
in
vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical Support [phone]
or go to
http://techservices.codesystems.com
2012 Audiovox Electronics Corporation.
All
rights reserved.
3

4
z
<(
~
z
a..
~
~
(/)
zr-
-:x:
a..(!)
('f)
-
.....J
r-
0:::
<(
r-
(/)
z
a..
<0
11
Pin Main Harness
GRAY/RED PARKING BRAKE INPUT
(-
)
PURPLE DOOR INPUT (
+)
GREEN DOOR INPUT ( - )
BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )
BROWN/BLACK HORN OUTPUT ( - )
RED/WHITE TRUNK RELEASE OUTPUT ( - )
BLUE/BLACK START STATUS
I
ACTIVE OUTPUT ( - )
PURPLE/WHITE TACH INPUT
GRAY HOOD PIN INPUT ( - )
BROWN/RED BRAKE INPUT ( + )
VIOLET/BLACK AUX 1 OUTPUT
(-)
3 Pin Parking Light Harness
BLACK GROUND
WHITE/RED PARKING LIGHT INPUT
WHITE PARKING LIGHT OUTPUT
6 Pin Start Harness
PURPLE STARTER
OUTPUT-
MOTOR SIDE
RED BATTERY 12V (
+)
ORANGE ACCESSORY 1 ( + )
PINK/WHITE IGNITION 2 ( + )
RED/WHITE BATTERY 12V (
+)
PINK IGNITION 1 (
+)
ca5553sstrev A

z~
-(.)
a..
a
C\I_..J
1
4 Pin Alternate Harness
BLACK/YELLOW PULSE DURING CRANK ( - )
GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
LT BLUE FACTORY ARM
I
PULSE AFTER START ( - )
LT GREEN/BLACK FACTORY DISARM
I
PULSE BEFORE START ( - )
2 Pin Door Lock Harness
BLUE UNLOCK
(-)
GREEN LOCK
(-)
11
Pin Main Harness
GRAY/RED PARKING BRAKE INPUT
(-)
Locate the vehicle's parking brake wire.
Verification: This wire will register ground when the vehicle's PARKING
BRAKE is engaged.
NOTE: The following connection is required for Manual Transmission
Mode.
2
PURPLE
DOOR TRIGGER INPUT (
+)
Locate the vehicle's dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or "0" Volts when the door is closed and the interior light is
off.
Connect the PURPLE wire to the vehicle's positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide.
2012Audiovox ElectronicsCorporation. All rights reserved. 5

6
3
GREEN
DOOR TRIGGER INPUT (-)
Locate the vehicle's dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle's negative door input wire(s).
NOTE:
Certain vehicles may require multiple connections. Refer to vehicle
application guide.
4 BLACK/WHITE ILLUMINATED ENTRYOUTPUT
(-)
This wire provides a ( - ) 500mA output for 30 seconds when the system is
disarmed capable of driving relays.
Locate the vehicle's dome light or pin switch wire.
5
Verification: This wire will register positive voltage or ground when the
vehicle's dome light is turned ON.
BROWN/BLACK HORN OUTPUT (- )
Locate the vehicle's horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current
output, 500mA.
6
RED!WHITE
TRUNK RELEASE OUTPUT
(-)
Locate the vehicle's trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 500mA and is configurable
in
option programming.
ca5553sst rev A

7 BLUE/BLACK START STATUS I ACTIVE OUTPUT
(-)
This wire provides a ground output when the remote start function is activated
and remains until 4 seconds after the remote start is shutdown. If this wire will
be used for multiple application's a 1 amp diode is required in-line with the stripe
facing the control module.
8
PURPLE!WHITE
TACH
INPUT
Locate the vehicle's ignition coil or fuel injector in the engine compartment.
Verification: Test using the following procedure:
1.
Set voltmeter to AC VOLTS.
2.
Attach positive lead of a volt meter to a constant 12-volt source.
3. Attach negative lead of a volt meter to the wire to be tested.
4. Start the engine.
5.
Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the engine's
RPM increases.
Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil
or fuel injector.
9 GRAY HOOD PIN INPUT
(-)
Install a Hood Pin Switch and connect to the GRAY wire. This connection is
required for Remote Start.
Verification: This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE:
Be sure to loom the wire, and seal the grommet.
1
0 BROWN/RED BRAKE INPUT (
+)
Locate the vehicle's brake light wire at the brake pedal mounted switch. This
connection is required for Remote Start.
Verification: This wire registers positive voltage when the brake pedal is
pressed.
Connect the BROWN/RED wire to the vehicle's brake light wire.
2012 Audiovox Electronics Corporation.
All
rights reserved. 7

8
1
11
VIOLET/BLACK AUX 1
This wire provides a ( - ) 500mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To
activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
3 Pin Parking Light Harness
BLACK
GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in
the driver's side kick panel area.
NOTE:
Do
not ground the BLACK wire with any other vehicle components.
2
WHITE/RED
PARKING
LIGHT INPUT
3
WHITE
PARKING
LIGHTOUTPUT
Locate the parking light output wire at the vehicle's light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
ca5553sst rev A

6 Pin Start Harness
1 PURPLE STARTER
OUTPUT
( + )
Locate the vehicle starter wire.
Verification:
This wire registers voltage
only
when the key is turned to the
START position.
Verification:
The starter wire registers voltage when the key is turned to the
START position.
Connect the PURPLE wire to the vehicle starter wire.
2 RED BATTERY 12V ( + )
Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification:
This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3
ORANGE
ACCESSORY 1 ( + )
Locate the vehicle's accessory wire at the ignition switch.
Verification:
This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START (or CRANK) position.
Connect the ORANGE wire to the vehicle's accessory wire.
4 PINK/WHITE IGNITION 2 ( + )
Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).
Verification:
This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.
Programmable output: IGN, ACC, Start.
2012 Audiovox ElectronicsCorporation.
All
rights reserved. 9

10
5
RED
!WHITE BATTERY 12V ( + )
Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6
PINK
IGNITION 1 (
+)
Locate the vehicle's ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle's Ignition wire.
This wire is also used for Ignition 1 Output.
4 Pin Alternate Harness
1
BLACKNELLOW
PULSE DURING CRANK
(-)
Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)
Verification: This wire registers voltage only in the start (crank) position of
the ignition switch.
Connect the BLACK/YELLOW wire as shown in the diagram below. Use an SPOT
relay (not supplied).
This output is configurable in option programming.
2
GREEN/WHITE
PULSEAFTER SHUTDOWN
(-)
This wire will supply a ( - ) 500mA pulse after the remote start shuts down. This
is typically used to re-lock the vehicle's doors if they unlock upon remote start
shutdown. It can also be used to pulse a door pin-switch wire to prevent the
vehicle's accessories from remaining on after remote start shutdown.
This output is configurable
in
option programming.
ca5553sst
rev
A