Code Alarm ca5554 Professional series User manual

12014 Voxx Electronics Corporation. All rights reserved.
PROFESSIONAL
SERIES
Automatic / Manual Transmission
Remote Start with Keyless Entry
Installation Guide
for models:
ca5554

2ca5554 Install rev A
Before You Begin.........................................................................................3
Wire Connection Guide............................................................................... 4
11 Pin Main Harness ................................................................................. 5
3 Pin Parking Light Harness...................................................................... 8
6 Pin Start Harness ................................................................................... 9
4 Pin Alternate Harness........................................................................... 10
2 Pin Door Lock Harness ........................................................................ 11
Additional Ports.........................................................................................15
Antenna / LED / Programming Port........................................................ 15
DBI Port...................................................................................................15
Telematic Interface Port........................................................................... 15
Set Up & Programming ............................................................................. 16
Transmitter Programming........................................................................ 16
Manual Feature Programming................................................................. 16
Programming Feature Banks .................................................................. 17
Tach Programming .................................................................................. 20
Smart Tachless Mode .............................................................................. 20
Feature Descriptions................................................................................. 21
Transmitter Button Functions .................................................................. 29
Remote Start Shutdown Diagnostics ...................................................... 30
System Layout........................................................................................... 31
Table of Contents

32014 Voxx Electronics Corporation. All rights reserved.
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support [phone]
or go to
http://avxtech1.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
“COMPUTER SAFE PROBE” as these can set off air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
BEFORE YOU BEGIN

4ca5554 Install rev A
6 Pin Start Harness
11 Pin Main Harness
3 Pin Parking Light Harness
1PURPLE STARTER OUTPUT - MOTOR SIDE
2RED BATTERY 12V ( + )
3ORANGE ACCESSORY 1 ( + )
4PINK/WHITE IGNITION 2 ( + )
5RED/WHITEBATTERY 12V ( + )
6PINK IGNITION 1 ( + )
6 PIN START
1GRAY/REDPARKING BRAKE INPUT ( - )
2PURPLE DOOR INPUT ( + )
3GREEN DOOR INPUT ( - )
4BLACK/WHITEILLUMINATED ENTRY OUTPUT ( - )
5BROWN/BLACKHORN OUTPUT ( - )
6RED/WHITETRUNK RELEASE OUTPUT ( - )
7BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
8PURPLE/WHITE TACH INPUT
9GRAY HOOD PIN INPUT ( - )
10 BROWN/REDBRAKE INPUT ( + )
11 VIOLET/BLACK AUX 1 OUTPUT ( - )
11 PIN MAIN

52014 Voxx Electronics Corporation. All rights reserved.
11 Pin Main Harness
4 Pin Alternate Harness
2 Pin Door Lock Harness
2 PURPLE DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
 Verication:This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or “0” Volts when the door is closed and the interior light is
off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide.
1 GRAY/RED PARKING BRAKE INPUT ( - )
Locate the vehicle’s parking brake wire.
  Verication:This wire will register ground when the vehicle’s PARKING
BRAKE is engaged.
NOTE: The following connection is required for Manual Transmission Mode.
1BLACK/YELLOWPULSE DURING CRANK ( - )
2GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
3LT BLUEFACTORY ARM / PULSE AFTER START ( - )
4LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
4 PIN
ALTERNATE
OUTPUT

6ca5554 Install rev A
4 BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )
This wire provides a ( - ) 200mA output for 30 seconds when the system is disarmed
capable of driving relays.
Locate the vehicle’s dome light or pin switch wire.
   Verication:This wire will register positive voltage or ground when the
vehicle’s dome light is turned ON.
5 BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
 Verication:This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 200mA.
6 RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
 Verication:This wire will register either positive voltage or ground when
the trunk release is activated.
 Thisisalowcurrentoutput,200mAandiscongurableinoptionprogramming.
3 GREEN DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
 Verication:This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide.

72014 Voxx Electronics Corporation. All rights reserved.
7 BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
This wire provides a ground output when the remote start function is activated and
remains until 4 seconds after the remote start is shutdown. If this wire will be used
for multiple application’s a 1 amp diode is required in-line with the stripe facing the
control module.
9 GRAY HOOD PIN INPUT ( - )
Install a Hood Pin Switch and connect to the GRAY wire. This connection is required
for Remote Start.
 Verication:This wire when connected will register ground when the
vehicle’s hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
10 BROWN/RED BRAKE INPUT ( + )
Locate the vehicle’s brake light wire at the brake pedal mounted switch. This
connection is required for Remote Start.
 Verication: This wire registers positive voltage when the brake pedal is
pressed.
Connect the BROWN/RED wire to the vehicle’s brake light wire.
8 PURPLE/WHITE TACH INPUT
Locate the vehicle’s ignition coil or fuel injector in the engine compartment.
 Verication:Test using the following procedure:
1. Set voltmeter to AC VOLTS.
2. Attach positive lead of a volt meter to a constant 12-volt source.
3. Attach negative lead of a volt meter to the wire to be tested.
4. Start the engine.
5. Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the engine’s
RPM increases.
Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or
fuel injector.

8ca5554 Install rev A
1 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface in
the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
3 Pin Parking Light Harness
2 WHITE/RED PARKING LIGHT INPUT
3 WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
  Verication: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
11 VIOLET/BLACK AUX 1
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
 Toactivaterefertothetransmitterbuttoncongurationchart.Pleaserefertothe
selectable options for timing.

92014 Voxx Electronics Corporation. All rights reserved.
6 Pin Start Harness
1 PURPLE STARTER OUTPUT ( + )
Locate the vehicle starter wire.
   Verication:This wire registers voltage only when the key is turned to the
START position.
   Verication: The starter wire registers voltage when the key is turned to the
START position.
Connect the PURPLE wire to the vehicle starter wire.
2 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
 Verication:This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3 ORANGE ACCESSORY 1 ( + )
Locate the vehicle’s accessory wire at the ignition switch.
 Verication:This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START (or CRANK) position.
Connect the ORANGE wire to the vehicle’s accessory wire.
Programmable output: IGN, ACC, Start.
4 PINK/WHITE IGNITION 2 ( + )
Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).
  Verication:This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.
Programmable output: IGN, ACC, Start.

10 ca5554 Install rev A
1 BLACK/YELLOW PULSE DURING CRANK ( - )
Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)
Verication: This wire registers voltage only in the start (crank) position of
the ignition switch.
 Thiswirewillsupplya(-)200mAoutputandcanbeconguredinoption
programming.
2 GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This
is typically used to re-lock the vehicle’s doors if they unlock upon remote start
shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s
accessories from remaining on after remote start shutdown.
 Thisoutputiscongurableinoptionprogramming.
6 PINK IGNITION 1 ( + )
Locate the vehicle’s ignition wire at the ignition switch.
   Verication:This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
5 RED/WHITE BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
 Verication:This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
4 Pin Alternate Harness

112014 Voxx Electronics Corporation. All rights reserved.
2 Pin Door Lock Harness
1 BLUE UNLOCK ( - )
2 GREEN LOCK ( - )
The door lock / unlock outputs are designed to control several different types of
systems which may require additional parts. Please review the wire and location
chart to see which type of door lock system is in your vehicle. The most common
types are shown in the following diagrams.
These wires supply a ( - ) 500mA output.
4 LT GREEN/BLACK FACTORY DISARM /
PULSE BEFORE START ( - )
This wire will supply a ( - ) 200mA pulse both upon disarming the system and when
the remote start feature is activated. Locate the factory perimeter alarm disarm wire
from the key cylinder inside the drivers door.
  Verication: This wire registers ground if the key is turned to the unlock
position in the driver’s door cylinder.
 Thisoutputiscongurableinoptionprogramming.
3 LT BLUE FACTORY ARM /
PULSE AFTER START ( - )
This wire will supply a ( - ) 200mA pulse both upon arming the system and upon
successful completion of the remote start activation sequence and is typically used to
re-lock the vehicle’s doors upon remote start if necessary.
 Thisoutputiscongurableinoptionprogramming.

12 ca5554 Install rev A
Negative Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will register ground when the Lock and Unlock
switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Positive Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will register positive voltage when the Lock and
Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Negative Locks:
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
Vehicle Door Lock
Control Relays
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Positive Locks:

132014 Voxx Electronics Corporation. All rights reserved.
Reverse Polarity Locks (5-Wire Door locks)
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will rest at ground and register positive
voltage when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Negative Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: This wire will show variable ground when the switch is activated.
 Pleaseconsultthewireandlocationchartforspecicresistorvaluesfor
your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Reverse Polarity Locks:
X
Cut
X
Cut
To Door Lock Motor
To Door Lock Motor
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output BLUE ( - ) Unlock Output
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Ground
Resistor

14 ca5554 Install rev A
Positive Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: This wire will show variable positive voltage when the switch is
 activated.Pleaseconsultthewireandlocationchartforspecicresistor
values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Adding Aftermarket Actuators
After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE
wires shown in the diagram below using (2) SPDT relays (not supplied).
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output BLUE ( - ) Unlock Output
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Resistor
30
87
87a
86 85
Fused +12 Volt
Battery Source
Door Lock
Actuator
30
87
87a
86 85
Chassis
Ground
Chassis
Ground
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Fused +12 Volt
Battery Source
M

152014 Voxx Electronics Corporation. All rights reserved.
Data Bus Interface Port
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces
to communicate with the vehicle’s Databus. When using the DBI port to control the
Flashlogic Door Lock and Transponder Interface modules the following options may
be available. Please refer to the D2D (Data to Data) function list available per vehicle
on the tech service web site.
Tach Input Brake Safety Shut Down
Trunk/Hatch Open Diesel Glow Plug Input
Door Lock Control Passlock / Passkey Interface (GM Only)
Dome Light Supervision Transponder Interface Activation
Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless
controls system)
Antenna / LED / Programming Port
Mount the supplied antenna/receiver to a clear spot on the vehicle’s windshield that
will not block the driver’s vision. A good location is usually high on the windshield
near the rear view mirror. Be careful not to mount the antenna/receiver on any
metallicwindowlm,asthiswilleffectsystemrange.Routetheantenna/receiver
cable to the control module and plug into the antenna port.
Additional Ports
Telematic Interface Port
This 4 pin port is used for Telematic Interface accessories, such as Car Connection
Pro, which can control some of the following features.
Door Lock Control Trunk Release
Sliding Doors AUX Output
Car Find Remote Start

16 ca5554 Install rev A
Manual Feature Programming - Feature Bank 2 - 5
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4)
 four,(5)ve,(6)sixand(7)sevenchirps.
5. Use the transmitter button to scroll through the selections in each feature
bank, the system will chirp to match the feature number.
6. Press the transmitter button to change the desired feature. The LED will
 ashindicatingthechangedfeature.
Defaulting All Features: Pressing the button anytime while in any of the feature
banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the ignition
is on, there is no time limit. To exit programming turn the IGNITION OFF.
Set Up & Programming
Transmitter Programming - Feature Bank 1
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Press 1 button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Pressing the override button at anytime during programming will advance to
the next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
NOTE:ThissystemhasPTN-ProgrammedTransmitterNotication.Eachtimethe
ignitionisturnedON,theLEDwillashthenumberoftransmittersprogrammedtothe
system.

172014 Voxx Electronics Corporation. All rights reserved.
Refer to transmitter programming.
Feature Bank 1 - 3 Chirps
Transm itter Programming
Feature Bank 2 - 4 Chirps
Security Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1Silent ChoiceONOFF
2Passive Locks Active Passive
3Passive ArmingActive Passive
4Siren / Horn - Arm/Disarm ChirpsN/A
5Siren Duration N/A
6SecurityN/A
7Anti-Hijack Mode N/A
8Orange - Ground w/ Armed Output N/A
9DBI Port ProtocolDBI ProtocolADS Protocol
10 Arm/Disarm
Chirp / Parking Light Pattern N/A
11 L.E.D. Output when Armed / LockedON OFF
Feature Bank 3 - 5 Chirps
Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1Extended Lock Pulse 1 Second 3.5 Seconds
1 Second
Lock, Double
Pulse Unlock
30 Second
Lock, Double
Pulse Unlock
Double Pulse
Lock, 1
Second Unlock
Factory Disarm
Lt Green / Black
Factory
Disa rm 2nd Unlock Factory Disarm
/ Start Status
Factory Disarm
350mS
Factory Disarm
500mS
3Ignition Controlled Locks OFFLock and
Unlock Lock Only Unlock Only
4Trunk Output Timing
Red / White Output
1 Second
Pulse10 Seconds 20 Seconds Latched until
IGN ON
Latched ON
until Button
Press
5Horn Output Timing16mS10mS30mS40mS50mS
6Real PanicON OFF
7AUX 1
Violet / Black Output
1 Second
PulseLatched Latched until
IGN ON
Dome Light
Output
Defrost Output
Single Pulse
Defrost Output
Latched 5 Min
2
NOTE: On this model the Lt Green / Black Output wire can be configured in Bank 3 or Bank 5. Any changes to this feature i
n
Bank 5 will override changes made in Bank 3.

18 ca5554 Install rev A
Feature Bank 4 - 6 Chirps
Remote Start Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1RF Start Chirp ON OFF
2Run Time 15 Minutes 5 Minutes10 Minutes 20 Minutes 45 Minutes60 Minutes
3Running LightsSteady Flashing
4Tach Mode Tach
Tachless
(Crank Average
/ Voltage)
Hybrid (Crank
Average / NO
Voltage)
DBI Port
5Voltage Level High Low
6Crank Time 1.0 Seconds0.8 Seconds1.5 Seconds2.0 Seconds4.0 Seconds
7Crank Averaging / Crank TimeAveraging Preset Time
8Gas / Diesel Gas 10 Second
Delay
15 Second
Delay
20 Second
Delay
45 Second
Delay
9Single / Double Press StartDouble Press Single Press
10 Ignition 2 Output
Pink / White Ignition Accessory Start / Crank
11 2 or 3 Hour StartNA
12 Turbo TimerNA
13 Transmission ModeAutomaticManual
14 Temperature StartOFF14F 5F -4F
15 Accessory Output
OrangeAccessoryIgnition Start / Crank
16 Pulse Additional Outputs when
Unlock is PressedOFFIGN, ACCY, GWR
IGN, ACCY,
GWR - Pulse
After Shutdown
17 Door Lock Control During Remote
StartOFF
Unlock before
Start, Lock
After Start
Unlock Before
Start
Lock After
Start
Lock After
Shutdown

192014 Voxx Electronics Corporation. All rights reserved.
Feature Bank 5 - 7 Chirps
4 Pin Alternate Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
Lt Green / Black Output
Pulse Before
Start / During
Unlock
Ground While
RunningIgnition AccessoryPulse During
Crank
2Lt Blue Output
Pulse After
Start / During
Lock
Ground While
RunningIgnition AccessoryPulse During
Crank
3Green / White Output Pulse After
Shutdown
Ground While
RunningIgnition AccessoryPulse During Crank
4Black / Yellow Output Pulse During
Crank
Ground While
RunningIgnition Accessory
NOTE: On this model the Lt Green / Black Output wire can be configured in Bank 3 or Bank 5. Any changes to this feature in
Bank 5 will override changes made in Bank 3.
1
NOTE: On this model the Lt Green / Black Output wire can be configured in Bank 3 or Bank 5. Any changes to this feature in
Bank 5 will override changes made in Bank 3.

20 ca5554 Install rev A
Tach Programming
The unit will not operate unless a tach signal is programmed or the tachless
option is turned ON. If an attempt is made to start the vehicle via the remote start
withoutrstprogrammingtach,theunitwillashtheparkinglights7timesindicating
tach has not been learned and stored. If the tach rate is not properly programmed
tothespecicvehicle,theunitmaynotrealizethatthevehicleisrunningincertain
instances and reengage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the ON position.
2. Press and release the valet/override button 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet/override button, then start the vehicle using
the key.
5. When the unit senses the tach signal, the parking lights will begin to
  ash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet/program push-button switch. 1 long chirp and the
parking lights will turn on for 2 seconds, indicating that the learned
tach signal is stored and the unit has exited tach learn mode.
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poortachsource,theparkinglightswillnotash.Tocorrectthissituation,locateand
connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach
learn routine.
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the
system and when activated will automatically change the Tach Mode feature in option
programming to Tachless without the need to enter the feature programming mode.
  1. Activatetheremotestart.Theparkinglightsshouldbeginashing7
times indicating no tach signal has been learned.
  2. Withinthe7ashtimeperiod,pressandholdthe button.
3. The system will chirp 1 time indicating the system is now in tachless
mode.