Code Alarm Professional ca5054 User manual

CCJCic~LA~m
~r::lOFESSIONA I
SEr::liES
Remote Start with Keyless Entry
Installation Guide
ca5054
2014 Voxx Electronics Corporation. All rights reserved. 4280598

Table of Contents
Before You Begin.........................................................................................3
Wire Connection Guide...............................................................................4
7 Pin Main Harness ...................................................................................5
3 Pin Parking Light Harness......................................................................7
6 Pin Start Harness ...................................................................................7
4 Pin Alternate Harness.............................................................................9
2 Pin Door Lock Harness ........................................................................10
Additional Ports.........................................................................................14
Antenna I LED I Programming Port........................................................ 14
OBI Port...................................................................................................14
Set Up &Programming .............................................................................15
Transmitter Programming........................................................................15
Manual Feature Programming................................................................. 15
Programming Feature Banks ..................................................................16
Tach Programming ..................................................................................18
Smart Tachless Mode..............................................................................19
Feature Descriptions.................................................................................19
Transmitter Button Functions ..................................................................26
Remote Start Shutdown Diagnostics ......................................................27
System Layout...........................................................................................28
2 ca5054 Install rev A.

BEFORE YOU BEGIN
FOR AUTOMATIC TRANSMISSION VEHICLES
ONLY.
. .
-
•
....
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys
in
vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical
Support
[phone]
or
go
to
http://avxtech1.com
2014 Voxx Electronics Corporation. All rights reserved. 3

4
z
<{
~
z
c..
,...._
(f)
zr-
-I
a..
C)
('I)-
.....J
.....
a::
<(
.....
(f)
z
a:
<0
z:::S:::
-(.)
a..
a
N.....J
7 Pin Main Harness
BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )
BROWN/BLACK
HORN OUTPUT
(-)
RED/WHITE TRUNK
RELEASE
OUTPUT ( - )
BLUE/BLACK
START
STATUS
I
ACTIVE OUTPUT ( - )
PURPLE/WHITE TACH INPUT
GRAY
HOOD PIN INPUT
(-)
BROWN/RED
BRAKE
INPUT ( + )
3 Pin Parking Light Harness
BLACK GROUND
WHITE/RED PARKING LIGHT INPUT
WHITE
PARKING LIGHT
OUTPUT
6 Pin Start Harness
PURPLE STARTER
OUTPUT-
MOTOR SIDE
RED BATTERY 12V (
+)
ORANGE ACCESSORY 1 ( + )
PINK/WHITE IGNITION 2 ( + )
RED/WHITE BATTERY 12V (
+)
PINK IGNITION 1 ( + )
4 Pin Alternate Harness
BLACK/YELLOW PULSE DURING CRANK ( - )
GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
LT BLUE FACTORY ARM
I
PULSE AFTER START
(-)
LT GREEN/BLACK FACTORY DISARM
I
PULSE BEFORE START ( - )
2 Pin Lock Harness
BLUE UNLOCK
(-)
GREEN LOCK
(-)
ca5054 Install rev A.

1
7 Pin Main H.arness
BLACK/WHITE ILLUMINATED ENTRY OUTPUT (-)
This wire provides a ( - ) 200mA output for 30 seconds when the system is disarmed
capable
of driving relays.
Locate the vehicle's dome light or pin switch wire.
2
Verification: This wire will register positive voltage or ground when the
vehicle's dome light
is turned ON.
BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle's horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current
output, 200mA.
3 RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle's trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 200mA and is configurable
in option programming
4 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )
This wire provides a ( - ) 200mA output when the remote start function is activated
and remains
until4 seconds after the remote start is shutdown. If this wire will be
used for multiple application's a 1 amp diode is required in-line with the stripe facing
the control module.
2014 Voxx Electronics Corporation. All rights reserved. 5

6
5
PURPLE/WHITE TACH INPUT
Locate the vehicle's ignition coil
or
fuel injector
in
the engine compartment.
Verification:
Test using the following procedure:
1.
Set voltmeter to AC VOLTS.
2.
Attach positive lead
of
a volt meter to a constant 12-volt source.
3.
Attach negative lead
of
a volt meter to the wire to be tested.
4.
Start the engine.
5.
Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the engine's
RPM increases.
Connect the PURPLE/WHITE wire to the negative side
of
the vehicle ignition coil
or
fuel injector.
6 GRAY HOOD PIN INPUT
(-)
Install a Hood Pin Switch and connect to the GRAY wire. This connection is required
for Remote Start.
Verification:
This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE:
Be sure to loom the wire, and seal the grommet.
7
BROWN/RED BRAKE
INPUT(+)
Locate the vehicle's brake light wire at the brake pedal mounted switch. This
connection is required for Remote Start.
Verification:
This wire registers positive voltage when the brake pedal is
pressed.
Connect the BROWN/RED wire to the vehicle's brake light wire.
ca5054 Install rev
A.

3 Pin Parking Light Harness
1 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
selftapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in
the driver's side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
2 WHITE/RED PARKING LIGHT INPUT
3
WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle's light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
1
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
6 Pin Start Harness
PURPLE STARTER OUTPUT ( + )
Locate the vehicle starter wire.
Verification: This wire registers voltage onlywhen the key is turned to the
START position.
Connect the PURPLE wire to the vehicle starter wire.
2014 Voxx Electronics Corporation. All rights reserved.
7

8
2
RED
BATTERY
12V
(
+)
Locate 1
of
the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification:
This wire will register ( + ) voltage
in
all positions
of
the ignition
switch.
Connect
the RED wire to the constant 12 Volt battery wire.
NOTE:
Remove
all fuses until all connections are made.
3
ORANGE
ACCESSORY
1 ( + )
Locate the vehicle's
accessory
wire
at
the ignition switch.
Verification:
This wire registers voltage
when
the key is turned to
ACC
(Accessory) and
the
ON (or
RUN)
position.
The
voltage
drops
out
when
the
key is turned to the START (or
CRANK)
position.
Connect
the
ORANGE
wire to the vehicle's accessory wire.
4
PINK/WHITE
IGNITION 2 (
+ )
Locate the vehicle's 2nd ignition wire
at
the ignition switch (if equipped).
Verification:
This wire registers voltage
when
the key is turned to the
ON
(or
RUN) position, but not the
ACC
(Accessory) position.
The
voltage
does
not
drop
out
when
the key is turned to the START (or
CRANK)
position.
Connect
the
PINK/WHITE
wire to
the
vehicle's ignition 2 wire.
Programmable output:
IGN, ACC, Start.
5
RED/WHITE
BATTERY
12V
(
+)
Locate 1
of
the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification:
This wire will register ( + ) voltage in all positions
of
the ignition
switch.
Connect
the
RED/WHITE
wire to
the
constant 12 Volt battery wire.
NOTE:
Remove
all fuses until all connections are made.
ca5054 Install rev
A.

6 PINK IGNITION 1 (
+)
Locate the vehicle's ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle's Ignition wire.
This wire is also used for Ignition 1 Output.
4 Pin Alternate Harness
1 BLACK/YELLOW PULSE DURING
CRANK (-)
Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)
Verification: This wire registers voltage only in the start (crank) position of
the ignition switch.
This wire will supply a
(-) 200mA output and can be configured in option
programming.
2 GREEN/WHITE PULSE
AFTER SHUTDOWN ( - )
This wire will supply a ( - )
200mA pulse after the remote start shuts down. This
is typically used to re-lock the vehicle's doors
if they unlock upon remote start
shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's
accessories from remaining on after remote start shutdown.
This output is configurable
in option programming.
3
LT BLUE FACTORYARM I
PULSE AFTER START ( - )
This wire will supply a ( - )
200mA pulse both upon arming the system and upon
successful completion
of the remote start activation sequence and is typically used to
re-lock the vehicle's doors upon remote start
if necessary.
This output is configurable
in option programming.
2014 Voxx Electronics Corporation. All rights reserved. 9

10
4
LT
GREEN/BLACK FACTORY DISARM I
PULSE BEFORE START ( - )
This wire will supply a ( - ) 200mA pulse both upon disarming the system and when
the remote start feature is activated. Locate the factory perimeter alarm disarm wire
from the key cylinder inside the drivers door.
Verification: This wire registers ground ifthe key is turned to the unlock
position in the driver's door cylinder.
This output
is
conffgurable
in
option programming.
2 Pin Door Lock Harness
1 BLUE UNLOCK
(-)
2 GREEN LOCK
(-)
The door lock I unlock outputs are designed to control several different types
of
systems which may require additional parts. Please review the wire and location
chart to see which type
of
door lock system is
in
your vehicle. The most common
types are shown
in
the following diagrams.
These wires supply a
(-)
500mA output.
ca5054 Install rev
A.