Code Alarm PROFESSIONAL SERIES User manual

1caSECRS / ca1BTW6 4280931 Owners rev A.
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
PROFESSIONAL
SERIES
Owner’s Guide
For Model:
CASECRS
&
CA1BTW6
Deluxe Vehicle Remote Start System

22018 Voxx Electronics Corporation. All rights reserved.
Table of Contents
Using Your Remote Control .......................................................3
Remote Starting your Vehicle ................................................3
Remote Start Shutdown.........................................................3
Entering the vehicle while it is running via Remote Start.......3
Preheating or Cooling the Vehicle’s Interior...........................3
Using the “Quick-stop” Feature..............................................4
User Programmable Run Time / Run Time Extension ...........4
Remote Start Safety Features ...............................................5
Remote Start Valet Mode............................................................5
System LED and Light Flash Indications .................................6
 2WayRemoteControlNotications.........................................6
Remote Control Programming...................................................7
Replacing Remote Control Batteries ........................................8

3caSECRS / ca1BTW6 4280931 Owners rev A.
Remote Starting Your Vehicle
To activate the remote start function, press and release the button 2 times within 2
seconds. The system will sound, the parking lights will ash 1 time and the system
will check the vehicle to ensure it is safe to start. If all safety parameters are correct,
the vehicle will start. The vehicle’s parking lights will turn on (or ash depending on
system settings) as a visual indication that the vehicle has started and is running.
If your vehicle stalls or does not start, the system will pause 5 seconds, then try
3 more times to start the vehicle (a total of 4 attempts). The system will pause 5
seconds between each start attempt.
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off. Pressing the
vehicle’s brake will also shutdown the remote start.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors. (Using the vehicle’s factory remote)
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.
Using Your Remote Control

42018 Voxx Electronics Corporation. All rights reserved.
Using the “Quick-stop” Feature
If you want to make a short stop and keep your vehicle running (to keep the interior
warm or cool), the quick-stop feature allows you to do this while keeping your vehicle
secure and your keys with you.
To engage Quick Stop:
1. Stop the vehicle and place the transmission in PARK.
2. With your foot off the brake pedal, press and release the button 2
times within 2 seconds. The LED will ash 3 times to conrm quick
stop is entered.
3. Remove the keys from the ignition and exit the vehicle. Press the
button to lock the vehicle’s doors if desired. (Using the vehicle’s factory
remote)
Note: Do not leave children or animals unattended in the vehicle when using the
quick-stop feature.
User Programmable Run Time / Run Time Extension
The system has the ability to allow the user to extend the time the vehicle will be
running under control of the remote start. This will only extend the run time back to
the current run time setting during the current remote start cycle. If your system is
set to run 15 minutes and the time remaining is 4 minutes, extending the run time
will reset the countdown timer to 15 minutes and your vehicle will continue to run for
another 15 minutes. Follow the steps below to extend the vehicle’s run time.
1. The remote start must already be active.
2. Press and release the button 4 times.
3. The system will chirp 1 time and ash the parking lights 4 times to
conrm that the run time has been reset.

5caSECRS / ca1BTW6 4280931 Owners rev A.
Remote Start Valet Mode
When valet mode is activated the status LED will light solid, and all security and
remote start functions will be disabled. To enter or exit valet mode simply follow the
steps outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the programming/valet button.
3. The LED will turn on solid when valet mode is active
4. Release the programming/valet button.
Remote Start Safety Features
For safety and security reasons, the system will shutdown or prevent the remote
vehicle starter from activating if any of the following occur:
1. The vehicle’s hood is open.
2. The brake pedal is pressed prior to turning the ignition key to the ON
position.
3. The engine is over-revved (tach checking only).
4. Valet Mode is active.

62018 Voxx Electronics Corporation. All rights reserved.
2WayRemoteControlNotications
FUNCTION BEEPS / LED FLASHES
Activation 1 Beep / Flash
Conrm Remote Start 4 Beeps / Flashes (repeats 3 times)
Remote Start Running 1 Flash per 3 seconds for duration run time
Remote Start Shutdown 3 Long Beep / Long Flashes (repeats 3 times)
Low Battery 2 Beeps / Flashes when button is pressed
System LED and Light Flash Indications
Status LED Flash Indications
LED Flashes Function
ON (Solid) Valet Mode
Remote Start Shutdown Diagnostics
Parking Light Flashes Shutdown Zone
3 Flashes Hood / Brake Input
4 Flashes Remote Start Valet Mode
7 Flashes Tach not learned / Crank Average not
learned

7caSECRS / ca1BTW6 4280931 Owners rev A.
Remote Control Programming
1. Turn the ignition ON.
2. Press and hold the valet/override button located on the antenna.
3. Within 10 seconds the LED’s will begin to ash.
4. Press 1 button of each transmitter you wish to program, the LED’s will
ash to conrm each transmitter.
5. Turn the ignition OFF
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
Programmed Transmitter Notication
As a security precaution each time the vehicle’s ignition is turn on the status LED
light with ash the number of transmitters programmed into the system. This helps
to identify unauthorized transmitters from accessing your vehicle. If you believe an
unauthorized transmitter has been programmed to your system, contact your installing
dealer for assistance.

82018 Voxx Electronics Corporation. All rights reserved.
1 Way Remote Control, CAT1LR:
The battery (model CR2032) inside each remote control should last approximately 1
year under normal use. When the battery becomes weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate
and the small LED on the remote control will dim. To replace the battery in the remote
control:
1. Unsnap and disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the battery
and replace with new CR2032 battery.
3. Reassemble the halves of the remote control.
4. Test operation of the remote control.
Replacing Remote Control Batteries
2 Way Remote Control, CAT1TW6:
The battery (model CR250) inside each remote control should last approximately 10
months under normal use. When the battery become weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate
and the small LED on the remote control will dim. To replace the battery in the remote
control:
1. Remove 1 screw and disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the battery
and replace with a new CR2450 battery.
3. Reassemble the halves of the remote control and reinstall the screw.
4. Test operation of the remote control.

9caSECRS / ca1BTW6 4280931 Owners rev A.

10 2018 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.