Code Alarm ca5554 Professional series User manual

12014 Voxx Electronics Corporation. All rights reserved.
PROFESSIONAL
SERIES
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Deluxe Vehicle Remote Start System
with 900Mhz 2 Way Conrming LCD
Remote Control
Owner’s Guide
for models:
ca5554

2ca5554 Owners rev A
Table of Contents
Using Your Remote Control.................................................................... 3
Using the Keyless Entry .................................................................... 3
Two Stage Door Unlock (optional)..................................................... 3
Activating Trunk Release (optional)................................................... 3
Activating AUX 1 (optional)................................................................ 3
Using the Progressive Car Finder Feature........................................ 3
Using the Personal Protection Alarm................................................. 3
Programmed Transmitter Notication................................................ 4
Valet Mode ........................................................................................ 4
Eliminating Lock / Unlock Notication Chirps .................................... 4
Using Your Remote Starter..................................................................... 5
Remote Start Ready Mode................................................................ 5
Cancelling Remote Start Ready Mode .............................................. 5
Remote Starting Your Vehicle............................................................ 6
Remote Start Shutdown .................................................................... 6
Entering Your Vehicle while it is Running via Remote Start .............. 6
Preheating or Precooling the Vehicle’s Interior ................................. 6
User Programmable Run Time / Run Time Extension....................... 7
Using the Quick Stop Feature ........................................................... 7
Operating the Daily Start Timer ......................................................... 7
Temperature Start Mode.................................................................... 8
Remote Start Safety Features........................................................... 8
Additional 2-Way LCD Remote Control Functions............................... 9
LCD Remote Control ICON’s ................................................................ 11
Transmitter Button Functions .............................................................. 12
Replacing Remote Control Batteries................................................... 13
Warranty Information ............................................................................ 14

32014 Voxx Electronics Corporation. All rights reserved.
Using Your Remote Control
Using the Keyless Entry
The button is used to lock the vehicle’s doors, the button is used to unlock the
vehicle’s doors. To lock or unlock the doors simply press and release the desired
function button one time. For your convenience, the parking lights will ash once when
the doors are unlocked and twice when the door are locked.
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the
system requires a second press of the or button to activate an audible locking/
unlocking response from the vehicle. If your system is set up for 2 step unlock, a third
press of unlock will activate the audible response.
Using the Progressive Car Finder Feature
Press the button to locate your vehicle. The system will ash the parking lights
and sound 5 times at low volume, increasing in volume each time the button is
pressed.
Using the Personal Protection Alarm (Panic)
Press and hold the button for 3 seconds to activate the personal protection alarm.
During panic mode, the normal function of the transmitter buttons will be suspended.
The transmitter’s and buttons can be used to lock and unlock the door (if the
option is installed). To stop the alarm, press and hold the button on the transmitter
again for 3 seconds. The system will automatically stop after 30 seconds.
Activating the Trunk Release Feature (Optional)
The button is used to open the trunk of the vehicle. To open the vehicle’s trunk
press and hold the button for 3 seconds.
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will unlock
only the driver’s door. Press again within three seconds to unlock the remaining
doors.
Activating AUX 1 (Optional)
If this feature is enabled on your system, pressing the and buttons
simultaneously will activate an optional feature. This feature can be programmed for a
wide range of functions like power window or sunroof automation, please consult your
installing dealer to determine the functionality of your system.

4ca5554 Owners rev A
Valet Mode
Valet Mode is used to disable the system from remote starting. To enter or exit valet
mode simply follow the 4 steps outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the programming/valet button.
3. The LED will turn on solid when valet mode is active
4. Release the programming/valet button.
Eliminating Lock / Unlock Notication Chirps
System lock and unlock notication chirps can be toggled ON or OFF without
entering the programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
Programmed Transmitter Notication
As a security precaution each time the vehicle’s ignition is turn on the status LED
light with ash the number of transmitters programmed into the system. This helps
to identify unauthorized transmitters from accessing your vehicle. If you believe an
unauthorized transmitter has been programmed to your system, contact your installing
dealer for assistance.

52014 Voxx Electronics Corporation. All rights reserved.
Using Your Remote Starter
Remote Start Ready Mode - Manual Transmission Vehicles Only
To activate the remote start function, the system must rst be in Remote Start Ready
Mode. Follow the steps below to enter remote start ready mode.
1. While the engine is running by the ignition key;
a. Set the parking brake
b. Place the transmission in neutral.
2. With your foot off the brake pedal, press and release the button 2
times within 2 seconds. The LED will ash 3 times and the parking
lights will turn on to conrm the system has entered quick stop mode.
3. Remove the keys from the ignition, the vehicle will remain running in
quick stop mode.
4. Exit the vehicle and close all vehicle doors.
5. Within 1 minute of step 1, press the button to lock the vehicle’s
doors. The vehicle will shutdown and sound 2 short chirps then 1 long
chirp to conrm ready mode is set.
Remote Start Ready Mode must be enabled if your vehicle is equipped with a
manual transmission.
Cancelling Remote Start Ready Mode
The system will exit remote start ready mode if any of the following occur:
Open any door
Open the hood or trunk (if connected)
Press the brake
Release the parking brake
Turn the ignition ON

6ca5554 Owners rev A
Remote Starting Your Vehicle
To activate the remote start function, press and release the button 2 times within 2
seconds. The system will sound, the parking lights will ash 1 time and the system
will check the vehicle to ensure it is safe to start. If all safety parameters are correct,
the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or ash
depending on system settings) as a visual indication that the vehicle has started and is
running.
If your vehicle stalls or does not start, the system will pause 5 seconds, then try
2 more times to start the vehicle (a total of 3 attempts). The system will pause
5 seconds between each start attempt. If the vehicle does not start after the 3rd
attempt, the system will abort the remote vehicle start process.
Note: Do not leave children or animals unattended in the vehicle when using the
remote start feature.
Note: Manual transmission vehicles - Remote Start Ready Mode must be set.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will activate
and heat or cool the vehicle’s interior to your setting.
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.

72014 Voxx Electronics Corporation. All rights reserved.
Using the “Quick-stop” Feature - Automatic Transmission Vehicles
If you want to make a short stop and keep your vehicle running (to keep the interior
warm or cool), the quick-stop feature allows you to do this while keeping your vehicle
secure and your keys with you.
To engage quick stop:
1. Stop the vehicle and place the transmission in PARK.
2. With your foot off the brake pedal, press and release the button 2
times within 2 seconds. The LED will ash 3 times to conrm quick
stop is entered.
3. Remove the keys from the ignition and exit the vehicle. Press the
button to lock the vehicle’s doors if desired.
Note: Do not leave children or animals unattended in the vehicle when using the
quick-stop feature.
Operating the Daily Start Timer
The system has the ability to start your vehicle based on a 24-hour countdown timer.
This feature requires a two-part activation sequence. From the remote, while in range
of the vehicle, pressing both the & buttons together will activate the 24 hour
countdown timer (the vehicle will start 24 hours from this time). Next, When you are
nished operating the vehicle for the day, perform the following steps to complete the
process.
1. Turn the ignition ON/OFF (vehicle must be disarmed).
2. Within 10 seconds, while pressing the brake, press and release the
button twice.
3. The vehicle will emit 2 chirps and ash the parking lights 4 times.
User Programmable Run Time / Run Time Extension
The system has the ability to allow the user to extend the time the vehicle will be
running under control of the remote start. This will only extend the run time back to the
current run time setting during the current remote start cycle. If your system is set to
run 15 minutes and the time remaining is 4 minutes, extending the run time will reset
the countdown timer to 15 minutes and your vehicle will continue to run for another 15
minutes. Follow the steps below to extend the vehicle’s run time.
1. The remote start must already be active.
2. Press and release the button 4 times.
3. The system will chirp 1 time and ash the parking lights 4 times to
conrm that the run time has been reset.

8ca5554 Owners rev A
Remote Start Safety Features
For safety and security reasons, the system will shutdown or prevent the remote
vehicle starter from activating if any of the following occur:
1. The vehicle hood is open.
2. The brake pedal is pressed prior to turning the ignition key to the ON
position.
3. The engine is over-revved (tach checking only).
4. Valet mode is active.
Temperature Start Mode
The system has the ability to start the vehicle if the temperature drops below a preset
temperature threshold. Once activated, the system will only start the vehicle one time
based on the temperature setting and will be cancelled if the vehicle is started with the
key or remote started by the transmitter. Temperature is read from the module, located
below the dashboard in most instances, and the vehicle’s interior temperature may
vary from the ambient temperature.
1. The vehicle must be armed.
2. Press and release both the & buttons together.
3. The vehicle will emit 1 chirp and ash the parking lights 1 time.
Note: This feature is defaulted OFF and must be set in option programming.

92014 Voxx Electronics Corporation. All rights reserved.
Check Vehicle Status
Press and release 2 times then press within 3 seconds, the transmitter will
display the current status of the vehicle.
Display Illumination
Press and hold the button for 1 second. The display will illuminate for 5 seconds.
Melody / Vibration Mode
To have the remote control vibrate, play a melody tone or both each time it receives a
response from the vehicle press and release then press and hold for 2
seconds.
Button Beeps
To toggle button beeps on or off press and release then press and hold for 2
seconds.
Battery Save Mode
While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any
incoming signals from the main unit until a button is pressed. The LCD screen will
display SAVE to indicate that power save mode is ON. To enter power save mode
press and hold for 5 seconds.
Clear Flashing Icons and Melody Sound
Press the button 3 times within 3 seconds. This will clear the melody sound and
ashing icons on the LCD screen.
Button Lock
Press and release then press hold the for 2 seconds to toggle the button lock
on or off. When the button lock is active, the remote control will beep/vibrate 2 times
when a button is pressed indicating it is locked.
Illumination
Press and release 2 times then press and hold for 2 seconds to toggle
illumination on or off. When on, the display will illuminate when it receives or sends a
command.
Additional 2-Way LCD Remote Control Functions

10 ca5554 Owners rev A
2 Car Mode
To control a second security system enter 2 car mode by pressing then press
and together for 3 seconds. When the icon appears on the transmitter’s LCD
screen it will control the second security system. Use the same method to exit 2 car
mode and resume control of the original vehicle’s security system.
NOTE: A second security system must be installed and the LCD transmitter must be
learned to it before this feature will operate the additional system.
Parking Meter Countdown
The parking meter countdown timer has 6 preset times, to access the preset times
and begin countdown press and release then press and hold for 2 seconds,
each additional press of will increase the countdown time.
Adjusting the Clock and Timer Settings
The clock, alarm clock and programmable countdown timer are accessed through the
Function Menu. Press and hold for 3 seconds to access the function menu, once
you have accessed the feature menu press and release to scroll through each
feature and follow the steps below to adjust the settings for each. Press and hold
for 2 seconds to exit the menu.
Clock Hour Press to increase or to decrease
Clock Minute Press to increase or to decrease
Alarm Clock Hour Press to increase or to decrease
Alarm Clock Minute Press to increase or to decrease
Alarm Clock ON / OFF Press to turn ON or to turn OFF
Countdown Timer Hour Press to increase or to decrease
Countdown Timer Minute Press to increase or to decrease
Countdown Timer ON / OFF Press to turn ON or to turn OFF

112014 Voxx Electronics Corporation. All rights reserved.
LCD Remote Control ICON’s
LOCK UNLOCK
VALET MODE
TRANSMITTING
TRUNK RELEASE
ENGINE RUNNING
2 CAR MODE
BATTERY INDICATORBATTERY SA
VE MODE
VIBRATE/SILENT MODE
PANIC
TIME COUNT DOWN
MELODY MODE
TIME DISPLAY
TIMER / TEMP
START MODES
ALARM CLOCK

12 ca5554 Owners rev A
Transmitter Button Functions
1 Way
Transm itterLock Unlock Car Find /
PanicStart N/AOperation Method
Lock XPress and Release
Unlock X Press and Release
Trunk XPush and Hold (3 Sec)
Car FinderX
Press and Release
PanicX
Push and Hold (3 Sec)
Remote Start XPress and Release (1 or 2 times depending
on selectable option)
Remote Start
Shut DownXPush and Hold (3 Sec)
Run Time
ExtentionXPress and Release 4 times.
Daily Start
TimerX X Press Lock + Start
Temperature
StartX X Press Unlock + Start While Armed
2 Way
Transm itterLock Unlock Car Find /
PanicStartFunction Operation Method
Lock XPress and Release
Unlock X Press and Release
Trunk XPush and Hold (3 Sec)
Car FinderX
Press and Release
PanicX
Push and Hold (3 Sec)
Remote StartX
Press and Release (1 or 2 times depending
on selectable option)
Remote Start
ShutdownXPush and Hold (3 Sec)
Run Time
ExtentionXPress and Release 4 times.
Daily Start
TimerXX
Press Lock + Start
Menu XPress and Hold
Temperature
StartXX
Press Unlock + Start While Armed

132014 Voxx Electronics Corporation. All rights reserved.
Replacing Remote Control Batteries
1 Way 4 Button Remote Control - Model CAT4
The batteries inside each remote control should last approximately 1 year under normal
use. When the batteries become weak you will notice the remote control range (the
distance from the vehicle the remote control will work) deteriorate and the small LED on
the remote control will dim. To replace the remote control batteries:
1. Using a coin, disassemble the halves of the remote
control.
2. Remove the old battery, observing the +/- symbols on the
batteries and replace with a new battery.
3. Reassemble the halves of the remote control
4. Test operation of the remote control.
2 Way LCD Remote Control - Model CATLCD
The AAA battery inside the 2-way LCD remote control should last approximately 6
months under normal use. When the battery becomes weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate and
the BATTERY icon on the LCD remote control will show 1 bar or less.
1. Gently slide the battery cover off of the remote control.
2. Remove the old AAA battery, observing the +/- symbols on the
battery, and replace with a new AAA battery.
3. Gently slide the battery cover on to the back of the remote control.
4. Test operation of the remote control.

14 ca5554 Owners rev A
Code Systems, Inc. Limited Lifetime Warranty
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security
product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below)
should this Product under normal use and conditions, be proven defective in material or workmanship
DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGINALLY INSTALLED, such
defect(s) will be repaired or replaced (at CODE’s option) without charge for parts directly related to
repairs of the defect(s).
Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for
a period of one (1) year from the date of purchase of the Product.
CODE accessories, sold separately, are covered by the applicable warranty accompanying the
accessory.
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from
the vehicle in which it was originally installed; or (2) the vehicle in which the Product was originally
installed is transferred to another party.
This warranty does not apply to any product damaged by accident, physical or electrical abuse, im-
proper installation, alteration, or use contrary to its intended function, re, ood, or other natural acts.
In order for the Product to be repaired or replaced under the terms of this warranty, the defective
Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail
sales receipt. The date of purchase and year, make and model of the vehicle in which the Product
was originally installed must be clearly indicated on the sales receipt.
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED.
ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, WHATSOEVER.
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION
LABOR.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation may not apply to you. This warranty gives you specic legal rights and you may also
have other rights which vary from state to state

152014 Voxx Electronics Corporation. All rights reserved.

16 ca5554 Owners rev A
Voxx Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PATENTED: www.voxxintl.com/company/patents