Code Alarm ca6554 User manual

CCJCc:~LA~m
i=)~OFESSIONAI
SE~IES
Security and Remote Start Installation Guide
for models:
ca6554
2014 Voxx Electronics Corporation. All rights reserved.
428592

Table
of
Contents
Before You Begin.........................................................................................4
Wire Connection Guide...............................................................................5
4 Pin Main Harness ...................................................................................7
6 Pin Start Harness ...................................................................................8
6 Pin Output Harness ..............................................................................10
8 Pin Input Harness.................................................................................
11
4 Pin Alternate Output Harness...............................................................14
4 Pin AUX Output Harness......................................................................15
3 Pin Door Lock Output Harness.............................................................16
AdditionaI Ports.........................................................................................
20
Antenna I LED I Programming Port........................................................20
OBI
Port...................................................................................................20
Telematic Interface Port...........................................................................20
Set Up &Programming .............................................................................
21
Transmitter Programming........................................................................
21
Manual Feature Programming.................................................................
21
Programming Feature Banks ..................................................................22
Tach
Programming ..................................................................................25
Smart Tachless Mode..............................................................................25
Adjusting the Shock Sensor ....................................................................26
Testing the Shock Sensor
........................................................................26
Chirp Delete -UserAccessible................................................................26
Dome Light Delay I Theater Dimming .....................................................26
2 ca6554 Install revA

Feature Descriptions.................................................................................
27
Transmitter Button Functions..................................................................
35
Security
TriggerZones..............................................................................
37
Remote
Start
Shutdown Diagnostics ......................................................
37
System
Layout
...........................................................................................
38
2014 Voxx Electronics Corporation. All rights reserved.
3

4
BEFoRE
YOU BEGIN
FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.
•
..
..
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Roll down window to avoid locking keys
in
vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT,
OR
"COMPUTER SAFE PROBE" as these can set off air
bags
or
damage vehicle computers.
Technical Support
(BOO)
421-3209
or
go
to
http://avxtech1.com
ca6554 Install revA

z
WHITE/RED PARKING LIGHT INPUT
<(
WHITE PARKING LIGHT OUTPUT
~
z
BLACK GROUND
a:
.q-
BROWN SIREN OUTPUT (
+ )
PURPLE STARTER
OUTPUT-
MOTOR SIDE
r-
RED BATTERY 12V (
+)
ex:
<(
ORANGE ACCESSORY 1 (
+ )
r-
(/)
z PINK/WHITE IGNITION 2 ( + )
a:
c:o
RED/WHITE BATTERY 12V (
+)
PINK IGNITION 1 (
+)
BROWN/BLACK HORN OUTPUT ( - )
r-
BLUE/BLACK START STATUS
I
ACTIVE OUTPUT
(-)
::>
n.
r-
VIOLET/BLACK
AUX
1 OUTPUT
(-
)
::>
0
z
RED/WHITE TRUNK RELEASE OUTPUT ( - )
n.
c:o
LT GREEN/BLACK FACTORY DISARM
I
PULSE BEFORE START ( - )
ORANGE GROUND
WHEN
ARMED OUTPUT ( - )
2014 Voxx Electronics Corporation. All rights reserved. 5

6
1-
::J
a..
z
z
a..
co
x,_
=>::::>
<(a_
Zl-
-:::>
a..o
~
z~
-(.)
a..
a
('t')_J
8
>.
Pin
Input
Harness
BLUE/WHITE INSTANTTRIGGER INPUT ( - )
GREEN
DOOR
TRIGGER INPUT
(-
)
PURPLE
DOOR
TRIGGER INPUT (
+ )
WHITE/BLUE
ExrRENAL
START
INPUT ( - )
GRAY
HOOD
PIN INPUT
(-)
GRAY/RED
PARKING
BRAKE
INPUT ( - )
BROWN/RED
BRAKE
INPUT ( + )
PURPLE/WHITE
TACH INPUT
4
!
Pi
·
"'
··
···.·······
AI
~
terriate
··.
Outp
·llt .
Ha
·
rness
BLACK/YELLOW PULSE DURING
CRANK
(-
)
GREEN/WHITE PULSE
AFTER
SHUTDOWN
(-
)
LT BLUE
FACTORY
ARM
I
PULSE
AFTER
START
(-)
LT GREEN/BLACK
FACTORY
DISARM
I
PULSE BEFORE
START
( - )
PINK/BLACK
AUX
5 OUTPUT ( - )
ORANGE/BLACK
AUX
4
OUTPUT
( - )
GRAY/BLACK
AUX
3
OUTPUT
( - )
WHITE/BLACK
AUX
2
OUTPUT
( - )
BLUE
UNLOCK
(-)
OPEN
GREEN
LOCK
(-)
ca6554 Install revA

4
Pln
Mail"l
Harness
1
WHITE/RED PARKING LIGHT INPUT
2
WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle's light switch.
Verification:
This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a
15
Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
3
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in
the driver's side kick panel area.
NOTE:
Do not ground the BLACK wire with any other vehicle components.
4
BROWN SIREN OUTPUT (
+)
Locate a suitable mounting location
in
the engine compartment for the siren, away
from moving parts.
With the bell ofthe siren aiming downwards, secure the siren
in
place using self
tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall and
connect to the RED wire on the siren.
NOTE:
Be sure to loom the siren wires, and seal the grommet.
2014 Voxx Electronics Corporation. All rights reserved.
7

8
1 PURPLE STARTER OUTPUT ( + )
Locate the vehicle starter wire.
Verification: This wire registers voltage onlywhen the key is turned to the
START position. Cut the vehicle's starter wire in halfwhen installing the
starter kill relay.
Verification afterstarter wire is cut:
KEY SIDE of starter wire registers voltage when the key is turned to the
START position.
MOTOR SIDE
of starter wire registers no voltage.
Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE
of the
vehicle starter wire when installing the starter kill relay.
2 RED BATTERY 12V ( +)
Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3 ORANGE ACCESSORY 1 ( + )
Locate the vehicle's accessory wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START (or CRANK) position.
Connect the ORANGE wire to the vehicle's accessory wire.
ca6554 Install revA

4
PINK/WHITE IGNITION 2 ( + )
Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).
Verification:
This wire registers voltage when the key is turned to the
ON
(or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.
Programmable output: IGN, ACC, Start.
5
RED/WHITE BATTERY 12V (
+)
Locate 1
of
the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification:
This wire will register ( + ) voltage
in
all positions
of
the ignition
switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6
PINK IGNITION 1 (
+)
Locate the vehicle's ignition wire at the ignition switch.
Verification:
This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key
is
turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle's Ignition wire.
This wire is also used for Ignition 1 Output.
2014 Voxx Electronics Corporation. All rights reserved.
9

10
6 Pin
Output
Harness
1
BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle's horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current
output, 200mA.
2 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )
This wire provides a
(-)
200mA output when the remote start function is activated
and remains
until4
seconds after the remote start
is
shutdown. Ifthis wire will be
used for multiple application's a 1 amp diode
is
required in-line with the stripe facing
the control module.
3
VIOLET/BLACK AUX 1
This wire provides a
(-)
200mA output capable
of
driving relays. For Control
of
optional accessories (i.e. Power Window/Sunroof, etc.).
To
activate refer to the transmitter button configuration chart. Please refer to
the
selectable options for timing.
4
RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle's trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release
is
activated.
This is a low current 200mA output and
in
configurable
in
option programming.
ca6554 Install revA