Code Alarm CA1BTW5 User manual

1CA1BTW5 / FLRS 4280847 Owners rev A.
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
PROFESSIONAL
SERIES
Owner’s Guide
For Model:
CA1BTW5
Flashlogic FLRS
RF Upgrade Kit

22017 Voxx Electronics Corporation. All rights reserved.
Table of Contents
Using Your Remote Control .......................................................3
Remote Start Valet Mode............................................................3
 2WayRemoteControlNotications.........................................4
Transmitter Programming..........................................................4
 ReplacingRemoteControlBatteries ........................................5

3CA1BTW5 / FLRS 4280847 Owners rev A.
Remote Starting Your Vehicle
To activate the remote start, press and release the button 2 times within 2
seconds. The vehicle will start and run the predetermined time set up during
installation (5 to 60 minutes selectable).
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off. Pressing the
vehicle’s brake will also shutdown the remote start.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors. (If equipped, press and release the button
2 times within 2 seconds while the vehicle is remote started)
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.
Using Your Remote Control
Remote Start Valet Mode
Enter / Exit Valet mode for systems using an Flashlogic FLRS kit.
1. Cycle ignition ON ve times [5x OFF/ON] rapidly. (complete this step
within 7 seconds)
2. Wait, LED 1 (on the FLRS kit) will turn solid RED for 2 seconds.
3. Turn ignition to OFF position.
4. Valet Mode Programming Procedure completed.
NOTE: In Valet Mode, the Remote starter is not functional. On units with Keyless
Entry, Lock and Unlock will remain functional. To exit valet mode: repeat steps 1 to 4.

42017 Voxx Electronics Corporation. All rights reserved.
Transmitter Programming
1. Turn the ignition ON.
2. Press and hold the valet/override button located on the antenna.
3. Within 10 seconds the LED’s will begin to ash.
4. Press 1 button of each transmitter you wish to program, the LED’s will
ash to conrm each transmitter.
5. Turn the ignition OFF
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
2 Way Remote Control Notications
FUNCTION BEEPS / LED FLASHES
Activation 1 Beep / Flash
Conrm Remote Start 4 Beeps / Flashes (repeats 3 times)
Remote Start Running 1 Flash per 3 seconds for duration run time
Remote Start Shutdown 3 Long Beep / Long Flashes (repeats 3 times)
Low Battery 2 Beeps / Flashes when button is pressed

5CA1BTW5 / FLRS 4280847 Owners rev A.
1 Way Remote Control, CAT1:
The battery (model CR2032) inside each remote control should last approximately 1
year under normal use. When the battery becomes weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate
and the small LED on the remote control will dim. To replace the battery in the remote
control:
1. Unsnap and disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the battery
and replace with new CR2032 battery.
3. Reassemble the halves of the remote control.
4. Test operation of the remote control.
 ReplacingRemoteControlBatteries
2 Way Remote Control, CAT1MTW:
The battery (model CR2032) inside each remote control should last approximately 10
months under normal use. When the battery become weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate
and the small LED on the remote control will dim. To replace the battery in the remote
control:
1. Remove 1 screw and disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the battery
and replace with a new CR2032 battery.
3. Reassemble the halves of the remote control and reinstall the screw.
4. Test operation of the remote control.

62017 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.