Code Alarm professional series PROCOMP User manual

12012 Audiovox Electronics Corporation. All rights reserved.
professional series
Security and Remote Start Installation Guide
for model:
PROCOMP

2 2012 Audiovox Electronics Corporation. All rights reserved.
Table of Contents
Before You Begin ...................................................................................... 4
Wire Connection Guide ........................................................................... 5
18 Pin Harness .......................................................................................... 7
4 Pin Power Harness ............................................................................. 13
2 Pin Transponder Bypass Harness ..................................................... 14
6 Pin Start Harness ................................................................................. 14
4 Pin Alternate Harness .......................................................................... 16
4 Pin Auxiliary Harness .......................................................................... 17
3 Pin Door Lock Harness ........................................................................ 19
Additional Ports ...................................................................................... 24
Antenna Port ........................................................................................... 24
Valet / Programming / Override Port ...................................................... 25
LED Port ................................................................................................... 25
DBI Port .................................................................................................... 25
Telematic Port .......................................................................................... 25
Set Up & Programming .......................................................................... 26
Transmitter Programming ........................................................................ 26
Manual Feature Programming ................................................................. 27
Programming Feature Banks .................................................................. 28
Dome Light Delay / Theater Dimming ..................................................... 29
Tach Programming .................................................................................. 30
Custom PIN Programming ........................................................................ 31

32012 Audiovox Electronics Corporation. All rights reserved.
Automatic / Manual Transmission Jumper ............................................. 31
Shock Sensor ......................................................................................... 32
Chirp Delete - User accessible .............................................................. 33
Feature Descriptions ............................................................................. 33
Security Trigger Zones .......................................................................... 41
Remote Start Shutdown Diagnostics ..................................................... 41
System Layout ........................................................................................ 42

4 2012 Audiovox Electronics Corporation. All rights reserved.
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support [phone]
or go to
http://techservices.codesystems.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
PROFESSIONAL INSTALLATION
STRONGLYRECOMMENDED

52012 Audiovox Electronics Corporation. All rights reserved.
18 Pin Main Harness
4 Pin Power Harness
1BLACK/WHITE ILLUMINATED ENTRY OUTPUT
2BLUE TRUNK PIN INPUT ( - )
3BLUE/WHITE INSTANT TRIGGER INPUT ( - )
4BLACK GROUND
5BROWN/BLACK HORN OUTPUT ( - )
6GREEN NEGATIVE DOOR TRIGGER
7GRAY/BLACK WAIT-TO-START INPUT ( - )
8WHITE/BLUE REMOTE START ACTIVATION INPUT ( - )
9GRAY HOOD PIN INPUT ( - )
10 WHITE PARKING LIGHT OUTPUT
11 RED/WHITE TRUNK RELEASE OUTPUT
12 PURPLE POSITIVE DOOR TRIGGER
13 BROWN SIREN OUTPUT ( + )
14 GRAY/RED PARKING BRAKE INPUT ( - )
15 LT. GREEN/ORANGE HEADLIGHT OUTPUT ( - )
16 ORANGE/WHITE GROUND WHEN DISARMED OUTPUT
17 PURPLE/WHITE TACH INPUT
18 ORANGE ARMED OUTPUT ( - )
18 PIN MAIN
1RED BATTERY 12V ( + )
2GREEN STARTER INPUT - KEY SIDE
3PURPLE STARTER OUTPUT - MOTOR SIDE
4PINK IGNITION 1 ( + )
4 PIN POWER

6 2012 Audiovox Electronics Corporation. All rights reserved.
6 Pin Start Harness
4 Pin Alternate Output Harness
4 Pin Auxiliary Output Harness
3 Pin Lock Output Harness
2 Pin Transponder Bypass Harness
1RED BATTERY 12V ( + )
2BLACK TRANSPONDER OUTPUT ( - )
2 PIN
1RED BATTERY 12V ( + )
2ORANGE ACCESSORY 1 ( + )
3ORANGE/WHITE ACCESSORY 2 ( + )
4PINK/WHITE IGNITION 2 ( + )
5BROWN/RED BRAKE INPUT ( + )
6BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
6 PIN START
1BLACK/YELLOW PULSE DURING CRANK ( - )
2GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
3LT BLUE FACTORY ARM / PULSE AFTER START ( - )
4LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
4 PIN
ALTERNATE
OUTPUT
1ORANGE/BLACK AUX 4 OUTPUT ( - )
2GRAY/BLACK AUX 3 OUTPUT ( - )
3WHITE/BLACK AUX 2 OUTPUT ( - )
4VIOLET/BLACK AUX 1 OUTPUT ( - )
4 PIN
AUXILIARY
OUTPUT
1BLUE/GREEN 2ND UNLOCK ( - )
2BLUE NEG UNLOCK / POS LOCK
3GREEN NEG LOCK / POS UNLOCK
3 PIN
LOCK

72012 Audiovox Electronics Corporation. All rights reserved.
18 Pin Main Harness
1 BLACK/WHITE ILLUMINATED ENTRY OUTPUT
Locate the vehicle’s dome light or pin switch wire.
Verification: This wire will register positive voltage or ground when the
vehicle's dome light is turned ON.
To select Negative or Positive polarity output refer to Fuse Placement Diagram
below:
2 BLUE TRUNK PIN INPUT ( - )
Connect the this wire to an optional grounding type trunk pin switch.
Verification: This wire when connected will trigger the security system.
(+)
(-)
Positive Polarity Output
(+)
(-)
Negative Polarity Output
4 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
3 BLUE/WHITE INSTANT TRIGGER INPUT ( - )
This wire is a GROUND input for an external sensor or secondary pin switch.
Verification: This wire when connected will trigger the security system.

8 2012 Audiovox Electronics Corporation. All rights reserved.
6 GREEN DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide.
5 BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 500mA.
7 GRAY/BLACK WAIT-TO-START INPUT ( - )
Locate the Diesel Wait-To-Start light wire at the instrument panel.
Verification: This wire registers positive or negative voltage when the wait-to-
start light illuminates.
For negative switching circuits follow the diagram below.
30
87
87a
86 85
GRAY/BLACK (-) 
Wait-To-Start Input
Ground
Chassis Ground
Wait-To-Start Bulb
At Instrument Panel
Vehicle Control
Module

92012 Audiovox Electronics Corporation. All rights reserved.
8 WHITE/BLUE REMOTE STARTACTIVATION INPUT ( - )
This wire will activate the Remote Start function when a GROUND pulse is applied to it
from an external device.
9 GRAY HOOD PIN INPUT ( - )
Install a Hood Pin Switch and connect to the GRAY wire. This connection is
required for Remote Start.
Verification: This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
For Positive switching circuits follow the diagram below. Use a SPDT relay (not
supplied).
GRAY/BLACK (-) 
Wait-To-Start Input
Vehicle Control
Module
Ground
Wait-To-Start Bulb
At Instrument Panel
1N4004 Diode

10 2012 Audiovox Electronics Corporation. All rights reserved.
(+)
(-)
Positive Polarity Output
(+)
(-)
Negative Polarity Output
11 RED/WHITE TRUNK RELEASE OUTPUT
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when the trunk
release is activated.
Trunk Release Polarity:
Connect the RED/WHITE wire to the vehicle’s trunk release wire at the trunk
release switch. Refer to Fuse Placement Diagram below for polarity.
10 WHITE PARKING LIGHT OUTPUT
Locate the vehicle’s parking light wire at the vehicle light switch.
Verification: This wire will register positive voltage or ground when the
vehicle parking light switch is turned to the ON position.
Parking Light Polarity:
Connect the WHITE wire to the vehicle’s parking light wire at the light switch.
Refer to Fuse Placement Diagram below for polarity.
(+)
(-)
Positive Polarity Output
(+)
(-)
Negative Polarity Output