Code Alarm ca6154 Professional Series User manual

CCJCc:~~Ja~m
i=»~OFESSIONAI
SE~IES
Security and Remote Start Installation Guide
for models:
ca6154
2014 Voxx Electronics Corporation. All rights reserved. 4280602

Table of Contents
Before You Begin.........................................................................................4
Wire Connection Guide...............................................................................5
4 Pin Main Harness...................................................................................7
6 Pin Start Harness ...................................................................................8
6 Pin Output Harness..............................................................................10
8 Pin Input Harness.................................................................................
11
4 Pin Alternate Output Harness...............................................................14
3 Pin Door Lock Output Harness.............................................................15
Additional Ports.........................................................................................19
Antenna I LED I Programming Port........................................................19
DBI Port...................................................................................................19
Telematic Interface Port...........................................................................19
Set Up &Programming .............................................................................20
Transmitter Programming........................................................................20
Manual Feature Programming.................................................................20
Programming Feature Banks ..................................................................
21
Tach Programming ..................................................................................24
Smart Tachless Mode..............................................................................24
Adjusting the Shock Sensor....................................................................25
Testing the Shock Sensor........................................................................25
Chirp Delete -UserAccessible................................................................25
Dome Light Delay I Theater Dimming .....................................................25
2 ca6154 Install revA

Feature Descriptions.................................................................................26
Transmitter
Button
Functions..................................................................
33
Security TriggerZones..............................................................................34
Remote Start Shutdown Diagnostics ......................................................34
System
Layout
...........................................................................................35
2014 Voxx Electronics Corporation. All rights reserved.
3

4
'
BEfoRE
YOU
:
·.,
BEGIN
' • .
::
..
· -
.:-_=_
.-
- .
~---
•
:,.:
.
.;
...
~-
FORAUTOMATIC TRANSMISSION VEHICLES ONLY.
•
....
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Roll down window to avoid locking keys
in
vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical
Support
{800) 421-3209
or
go
to
http://avxtech1.com
ca6154 Install revA

z WHITE/RED PARKING LIGHT INPUT
<(
WHITE PARKING LIGHT OUTPUT
~
z BLACK GROUND
a:
-.;~"
BROWN SIREN OUTPUT (
+ )
PURPLE STARTER
OUTPUT-
MOTOR SIDE
.....
RED BATTERY 12V (
+)
ct:
<(
ORANGE ACCESSORY 1 (
+ )
.....
C/)
z PINK/WHITE IGNITION 2 (
+)
a:
co
RED/WHITE BATTERY 12V (
+)
PINK IGNITION 1 (
+)
$
'C
R-J:
Jl
,
OufptJJ
:
l!la
·
t:J1e~
.
s
..
..
'.
i
'!
~
' ·
...
' ' -
_:
______
:
__
_
---
__
:
_:-
--
- : :-
-.
·
_:-
.' ; '
-·
·-
. ... .
·-;
. .
:-
.. .
..
BROWN/BLACK HORN OUTPUT ( - )
1-
BLUE/BLACK START STATIJS
I
ACTIVE OUTPUT ( - )
::>
a..
1-
VIOLET/BLACK AUX 1 OUTPUT ( - )
::>
0
z
RED/WHITE TRUNK RELEASE OUTPUT ( - )
a..
co
LT GREEN/BLACK FACTORY DISARM
I
PULSE BEFORE START ( - )
ORANGE GROUND
WHEN
ARMED
OUTPUT ( - )
2014 Voxx Electronics Corporation. All rights reserved.
5

6
I-
=>
c..
z
z
c..
co
z~
-(.)
c..
a
M...J
:
;
I
;:.
,J
·
n
···
·
~
..
,.
lnput
H.
arness
,,_;_;::.:::~>--:
(~=::-
:
>::~:(
-_
-',·
BLUE/WHITE INSTANT TRIGGER INPUT ( - )
GREEN DOOR TRIGGER INPUT
(-
)
PURPLE DOOR TRIGGER INPUT (
+ )
WHITE/BLUE EXTRENAL START INPUT ( - )
GRAY
HOOD PIN INPUT
(-)
GRAY/RED PARKING BRAKE INPUT ( - )
BROWN/RED BRAKE INPUT ( + )
PURPLE/WHITE TACH INPUT
BLACK/YELLOW PULSE DURING CRANK ( - )
GREEN/WHITE PULSE AFTER SHUTDOWN
(-)
LT BLUE FACTORY ARM
I
PULSE AFTER START ( - )
LT GREEN/BLACK FACTORY DISARM
I
PULSE BEFORE START
(-
)
~
·
I.l~~.
I
·['
P
:
I
.
o
~
'·.
~oc~
OJ,~put
.:.
ij
.
all'ft~s
.
...
;:"
-.
-
_-
_ .- -.
·-
.
_:_
--~,
.-,__
·_
.\---
-·
- . .
~-
-_--=:---=,::·:·-:
:,_----_:=_.
-
-,;.
:··-·
-~-
:;.
BLUE UNLOCK
(-)
OPEN
GREEN LOCK
(-)
ca6154 Install revA

1
WHITE/RED PARKING LIGHT INPUT
2
WHITE
PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle's light switch.
Verification:
This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15Amp
max
fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
3
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
BLACK
GROUND
Connect
the
BLACK wire to a solid chassis ground point using a ring terminal and
selftapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface in
the driver's side kick panel area.
NOTE:
Do not ground the BLACK wire with any other vehicle components.
4
BROWN
SIREN OUTPUT (
+ )
Locate a suitable mounting location
in
the engine compartment for the siren,
away
from moving parts.
With the bell
of
the siren aiming downwards, secure the siren in place using
self
tapping screws, being careful not do drill into any hoses, wiring
or
components.
Connect
the
BLACK siren wire to a chassis ground using a ring terminal and
self
tapping
screw
(not supplied).
Route the BROWN siren output wire from the control module through the firewall and
connect to
the
RED wire on the siren.
NOTE:
Be sure to loom the siren wires, and seal the grommet.
2014 Voxx Electronics Corporation. All rights reserved.
7

8
<6
..
Pi
'.
n
·Start;
Harness
1 PURPLE STARTER OUTPUT ( + )
Locate the vehicle starter wire.
Verification: This wire registers voltage onlywhen the
key
is turned to the
START position. Cut the vehicle's starter wire
in
half
when
installing the
starter kill relay.
Verification
after
starterwire is cut:
KEY SIDE
of
starter wire registers voltage when the
key
is turned to the
START position.
MOTOR SIDE
of
starter wire registers no voltage.
Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE
of
the
vehicle starter wire when installing the starter kill relay.
2 RED BATTERY 12V (
+)
Locate 1
of
the vehicle's constant 12 Volt battery wires at
the
ignition switch.
Verification: This wire will register
(+)voltage
in
all positions
of
the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3
ORANGE ACCESSORY 1 ( + )
Locate the vehicle's accessory wire at the ignition switch.
Verification: This wire registers voltage when the key
is
turned to
ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START (or CRANK) position.
Connect the
ORANGE
wire to the vehicle's accessory wire.
ca61541nstall revA

4
PINK/WHITE IGNITION 2 ( + )
Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).
Verification: This wire registers voltage when the key
is
turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.
Programmable output: IGN, ACC, Start.
5
RED/WHITE BATTERY 12V (
+)
Locate 1
of
the vehicle's constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage
in
all positions
of
the ignition
switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6
PINK IGNITION 1 ( + )
Locate the vehicle's ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key
is
turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle's Ignition wire.
This wire is also used for Ignition 1 Output.
2014 Voxx Electronics Corporation. All rights reserved.
9

10
1
BROWN/BLACK HORN OUTPUT ( - )
Locate the vehicle's horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current
output, 200mA.
2
BLUE/BLACK START STATUS
I
ACTIVE OUTPUT ( - )
This wire provides a ( - ) 200mAoutput when the remote start function is activated
and remains
until4
seconds after the remote start is shutdown.
If
this wire will be
used for multiple application's a 1 amp diode is required in-line with the stripe facing
the control module.
3
VIOLET/BLACK AUX 1
This wire provides a ( - ) 200mA output capable
of
driving relays. For Control
of
optional accessories (i.e. Power Window/Sunroof, etc.).
To
activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
4
RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle's trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage
or
ground when
the trunk release is activated.
This is a low current 200mAoutput and in configurable
in
option programming.
ca6154 Install revA