Code ME24 User manual
CODE-ME24
Access Controller Series
USER MANUAL
SPECIFICATION WIRE REQUIREMENT
Control Mode
Processor
Reader Interface
Number of Readers
Lock Output Relays
Card Capacity
Record Capacity
Communication Mode
Auxullary Monitored Inputs
Auxillary Relay Outputs
Working Voltage
Working Current
Output Drive
Working Environment
CODE-ME24
Two-door two-way or Four-door one-way
16 bit high speed CPU
Wiegand 26/34 Bit
4
4
20000
50,000 event records + 20,000 alarm records
TCP/IP
4 inputs
4 ouputs
10-15V DC
<100mA
12V/3A
Temperature: -10ºC-+55ºC Humidity: 10%-90%
PC > Switch/
Network Controller
Switch > Controller
Reader > Controller
Lock > Controller
Exit Button > Controller
Emergency Break Glass
Unit >
Wire Standard
8-core UTP
8-core UTP
8-core UTP
2-core cable
2- core cable
2-core cable
Wire Distance
100m
100m
60m
60m
60m
60m
1.1 Disconnect the power supply of all electronic components.
1.2 Ensure all the components are correctly connected.
1.3 Connect all the components according to “Access Controller Wiring Diagram”
on the right of this page.
1.4 Reconfirm that all the components are correctly connected.
1.5 Switch on the power supply of both the computer and the controller and start
commissioning. For commissioning procedures, please refer to Access Controller
Installation Manual.
2.1 Connect the system according to the instructions described in this manual.
2.2 Please use the specified power supply.
2.3 Please do not touch PCB components as this will invalidate warranty
2.4 When installation is completed, please check: Is the connection correct; Is there any
short circuit or open circuit; Is the back of controller completely separated from
conductive materials.
Notice: M controller series work with Code security management software only.
Failure to follow the instructions below may lead to the malfunction of the system.
INSTALLATION PROCEDURE ACCESS CONTROLLER WIRING DIAGRAM
Important Notices
In the diagram, all the alarm outputs are
connected in normal open mode. Normal close
mode can be selected as optional.
LED Indicator:
LED1: Lock-1 Controlled Indicator
LED2: Door-1 Magnet Alarm Indicator
LED3: Lock-2 Controlled Indicator
LED4: Door-2 Magnet Alarm Indicator
LED5: Alarm Output-1 Indicator
LED6: Alarm Output-2 Indicator
LED7: Alarm Output-3 Indicator
LED8: Alarm Output-4 Indicator
POWER: Power Indicator
RD-OK: Reader Interface Indicator
Please note all relays are programmable
Four Door One Way
BUZZER/YELLOW
The Controller can be defined as Two- door
two-way reading or Four-door One-way
reading. The detail information about
controller interface. Please refer to picture 1
and picture 2.
Please note: Connect
YELLOW wire if buzzer is to
be active when LED is green
Reader Function Controller
Black GND RD-
Red +12V RD+
Green DATA0 D0
White DATA1 D1
Blue LED BUZ
Yellow BUZZER BUZ
CONTROLLER INTERFACES
All output relays are of default setup and are programmable
CODE-ME24
Two-door Two-way
All output relays are of default setup and are programmable
CODE-ME24
Four-door One-way
Reader Function Controller
Black GND RD-
Red +12V RD+
Green DATA0 D0
White DATA1 D1
Blue LED BUZ
Yellow BUZZER BUZ
code
CODE-2609
CODE-2611
CODE-2621
CODE-2631
CODE-2641
CODE-FC02
OTHER PRODUCTS IN THE RANGE
description
Mini Proximity Reader
Regular Proximity Reader
Keypad Proximity Reader
Box Proximity Reader
Vandal Resistant Mini Proximity Reader
Card Distributor
COMMUNICATION MODE CLEAR COMMUNICATION PASSWORD
Controller can connect with switch
or computer by network wire via
direct connection or cross over
cable.
Connect with
router or
computer
directly
Code Software and controller can not
communicate when their passwords are
different. In case password is unknown,
press “Clear Communication Password”
button to clear the password.
