Coemar Reflection LEDko User manual

Instruction manual
Manuale di istruzioni
Ver. 2.1
DIS140

Serial number/numero di serie
Date of purchase/data di acquisto
Retailer/fornitore
Address/indirizzo
Suburb/cap/città
Capital city/provincial
State/stato
Tel./fax
Please note in the space provided above the relative service information of the model and the
retailer from whom you purchased your
Reflection LEDko
: this information will assist us in
providing spare parts, repairs or in answering any technical enquiries with the utmost speed and
accuracy.
Prendete nota, nello spazio apposite, dei dati relative al modello e al rivenditore del vostro
Reflection LEDko
questi dati ci permetteranno di assistervi con la massima rapidità e precisione.
WARNING:
the security of the fixture is granted only if these instructions are strictly followed;
therefore it is absolutely necessary to keep this manual.
ATTENZIONE:
la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti
istruzioni, pertanto è necessario conservarle.
User Manual Version 2.1
edition March, 2012

English
5
Index
1.Packaging and transportation....................................................................................................................................................... 6
1.1 Packaging................................................................................................................................................................................. 6
1.2 Trasportation............................................................................................................................................................................. 6
2. General information ...................................................................................................................................................................... 6
2.1 Important safety information...................................................................................................................................................... 6
2.2 Warranty conditions .................................................................................................................................................................. 6
2.3 EC Norms ................................................................................................................................................................................. 6
3. Product specifications.................................................................................................................................................................. 7
3.1 Technical characteristics........................................................................................................................................................... 7
3.2 Dimensions............................................................................................................................................................................... 7
3.3 Unit’s main components............................................................................................................................................................ 8
4. Installation ..................................................................................................................................................................................... 9
4.1 Optical installation..................................................................................................................................................................... 9
4.2 Mechanical installation.............................................................................................................................................................. 9
4.3 Safety chain............................................................................................................................................................................ 10
4.4 Adjusting unit’s tilt................................................................................................................................................................... 10
5. Powering up................................................................................................................................................................................. 11
5.1 Operating voltage and frequency............................................................................................................................................ 11
5.2 Connection to mains power..................................................................................................................................................... 11
6. Control signal connections ........................................................................................................................................................ 12
6.1 Control signal connection by XLR5 plugs................................................................................................................................ 12
7. Turning on the projector............................................................................................................................................................. 12
7.1 DMX address of the unit.......................................................................................................................................................... 12
7.2 DMX functions......................................................................................................................................................................... 13
7.2.1 FullSpectrum DMX chart...................................................................................................................................................... 13
7.2.2 VariWhite DMX chart............................................................................................................................................................ 15
7.2.3 White 3200K DMX chart....................................................................................................................................................... 17
8. Display panel functions.............................................................................................................................................................. 18
8.1 Quick guide to menu............................................................................................................................................................... 18
8.2 Rapid count............................................................................................................................................................................. 18
8.3 Main function menu (FUNC) ................................................................................................................................................... 19
8.3.1 TEST/COLOR Functions FullSpectrum................................................................................................................................ 20
8.3.2 TEST Functions VariWhite................................................................................................................................................... 21
8.3.3 TEST Functions White 3200K.............................................................................................................................................. 21
8.4 Measures and test s(MEAS)................................................................................................................................................... 22
8.5 User settings (MODE)............................................................................................................................................................. 23
8.6 Connecting DR1 and DR1 Plus............................................................................................................................................... 24
8.6.1 Saving and loading colors banks by using DR1 Plus........................................................................................................... 24
8.7 Electronic alignment of the leds.............................................................................................................................................. 24
9. Error messages ........................................................................................................................................................................... 26
10.Accessories and spare parts..................................................................................................................................................... 26
11. Maintenance............................................................................................................................................................................... 27
11.1 Periodic cleaning................................................................................................................................................................... 27
11.2 Periodic controls.................................................................................................................................................................... 27
11.3 Fuses:................................................................................................................................................................................... 27
12. F.A.Q. and answers................................................................................................................................................................... 27

English
6
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in the
componentry and in the technology used. We renew our invitation to you to complete the service information form on the previous
page. This will assist in providing prompt and accurate advice from your Coemar service centre, which you can thoroughly trust and
to which you can submit any requests for service or information. Following the instructions and procedures outlined in this manual
will ensure the maximum efficiency of this product for years to come.
1.Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suffered any damage during the transportation. In case of
damage to the fixture, contact your currier and your supplier immediately by telephone, fax or email, and inform them you will
formally notify them in writing through registered letter.
Packing List
Make sure the packaging contains:
1 Reflection LEDko
2 This instruction manual.
3-main power plugs
1.2 Trasportation
Reflection Ledko must be transported exclusively in its original packaging or in an appropriate flight case.
2. General information
2.1 Important safety information.
Fire prevention:
1.Never locate the fixture on any flammable surface.
2.Minimum distance from flammable materials: 0,5m.
3.Minimum distance from the closet illuminable surface: 0,5m.
4.Replace any blown or damaged fuse only with those of identical values. Refer to the schematic diagram if there is any doubt.
5. Connect the projector to mains power protected by a thermal magnetic circuit breaker.
Preventing from electric shock.
1. Presence of high voltage inside of the fixture. Insulate the projector from mains supply before opening or performing any function
which involves touching the inside of the fixture, including lamp replacement..
2. For the connection to the mains, adhere strictly to the guidelines outlined in this manual.
3. The level of technology of Reflection LEDko requires the use of specialised personnel for all service applications; refer all work
to your authorised Coemar service centre.
4. A good earth connection is essential for the proper functioning of the projector. Never connect the fixture if there is no earth
connection.
5.Mains cables must not come into contact with other cables.
6.Do not operate the projector with wet hands or in an area where water is present.
7.The fixture must never be located in an exposed position, or in areas of extreme humidity.
Safety.
1. The projector must always be installed with bolts, clamps, or other fixing devices which are suitably rated to support the weight of
the projector.
2. Always use a secondary safety fixing device with chain or steel wire of a suitable rating to sustain the weight of the unit in case of
failure of the principal fixing point.
3. The external surfaces of the unit, at various points, may reach 80°C. Never handle the unit until at least 10 minutes have elapsed
since the lamp was turned off
4. Never install the fixture in an enclosed area lacking sufficient air flow; the room temperature must not exceed 35°C.
5. The projector contains electronic and electrical components which must under no circumstances be in contact with water, oil or
any other liquid. Failure to do so will compromise the proper functioning of the projector.
2.2 Warranty conditions
1. The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects.
2. The warranty does not extend to damage caused by inappropriate usage, use by inexperienced operators or inadequate
maintenance.
3. The warranty is immediately void if the projector has been tampered or opened by unauthorized personnel.
4. The warranty does not extend to fixture replacement.
5. Both the serial number and the model of the projector are required for any advice or service from your authorised service centre.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.

English
7
3. Product specifications
3.1 Technical characteristics
Power
90-250 Vac 50/60Hz Autosensing
Maximum current
0,82A @230 Vac, - 1,7 A @115Vac
Power factor
Cos ϕ= 0,9
Light source wattage
163 W
Maximum room temperature
35°C/95°F
Weight
6 Kg./13.2 lbs (main body)
Grado di protezione
IP20
3.2 Dimensions

English
8
3.3 Unit’s main components
Components description
1- Yoke
6- Light source
2- Casing 7- Shaping blade pack
3- Rear header
8- Optics
4- Electronic sector
9- Nose casing
5- Cooling sector
WARNING! Never park the projector which hasn't installed optical without the dust cap.
1
2
3
4
5
6
7
8
9

English
9
4. Installation
4.1 Optical installation
4.2 Mechanical installation
Reflection LEDko may be hung from an appropriate structure in any position or on tripode.
If hanging the fixture from a lighting truss or similar, we recommend the use of an appropriate clamp “A”, as shown in the following
diagram.
WARNING!
Always ensure that your support structure and fixing (bolts, clamps, etc…)
are rated to support the weight of the fixture.
A

English
10
4.3 Safety chain
When hanging Reflection LEDko it is recommended to use a safety chain, as required by current legislation. The safety chain
must pass through the handles of the unit and then attached to the structure.
If using steel cables and chains not Coemar's production, make sure they are suitable to support the weight of the unit according to
normative UL/ETL ( required: the weight of 6 complete devices for at least one hour)
4.4 Adjusting unit’s tilt
In order to adjust the tilt of the unit simply loose the side handle adjust the tilt and lock the yoke by tightening the handle again.

English
11
5. Powering up
5.1 Operating voltage and frequency.
The unit may operates at voltages ranges from 90 to 250VaC at a frequency of 50 or 60 Hz. It is not needed to effect any setup
procedures: Reflection LEDko will automatically adjust its operation to suit any frequency or voltage within this range.
5.2 Connection to mains power
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent International standards.
Note: in case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusively (cable 3 X
1,5 ø external 10 mm, rated 300/500V, tested to 2 KV, operating temperature -40°C +180°C, Coemar cod. CV5311).
Connection to mains power
Reflection LEDko is equipped with two power connectors, one as input and one as output, which can be used to connect more
fixtures in series (no more than 16 units @ 230V or 8 units @ 115V.).
The max absorption of Reflection LEDko is reported in the following table:
-230/240V 0,82 A constant during normal exercise.
-100/115V 1,7 A constant during normal exercise.
WARNING !
Never link more than 16 units at 230 V or 8 units at 115 V.
In the following figure you can see an example of series connection:
WARNING!
• The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to regulatory norms is strongly
recommended.
• Reflection LEDko should not be powered through a dimmer as this may damage the internal switching power supply.
•
Prior to connecting the device to mains power, ensure that the mains characteristics are within the recommended range
for use with Reflection LEDko.
• All cabling and connections should be carried out by suitably qualified personnel.
Blu (CE) / Bianco(UL-ETL)
Blue (CE) / White (UL-ETL)
Marrone (CE) / Nero (UL-ETL)
Brown (CE) / Black (UL-ETL)
Giallo verde (CE) / Verde (UL-ETL)
Green yellow (CE) / Green (UL-ETL)

English
12
6. Control signal connections
6.1 Control signal connection by XLR5 plugs.
The digital control signal is transmitted to the projector via a two pole cable screened as per International standards for the
transmission of DMX 512 data. The connection must be serial, using connectors XL5 male and female located on the back of
Reflection LEDko labelled DMX512 IN e OUT (see diagram).
Pin 1= GROUND
Pin 2= DATA-
Pin 3= DATA+
Pin 4 =nc
Pin 5 =nc
WARNING !
Make sure that screening and conductors are not in contact one another or with the metal housing of the connector.
Pin#1 and housing never must be connected to the power supply unit.
7. Turning on the projector
After having followed the preceding steps described, proceed with the power supply and turn on the projector connecting it to the
mains power.
The software version installed on the internal microprocessors will be shown on the display, suddenly it will show the current DMX
addressing. If the address blinks, it means that the DMX signal has not been received. Check the connection cable and the mixer
functioning.
7.1 DMX address of the unit
Each projector can use 12, 8 or 4 address channels for its complete operation and is controlled by a DMX 512 signal (for further
information, see section 7.2, DMX functions).
DMX addressing
When powered up initially, each projector will show A001, which indicates DMX address 001; for example, when set at 12 channels
a projector thus addressed will respond to commands of channel 1 to 12 from your DMX 512 controller . A second unit must be
addressed as A013,a third one as A025 and so on. The operation must be carried out on every Reflection LEDko which has an
address different from A001..
Altering DMX address.
1. Press the + or – button until the display shows the required DMX address. The digits on the display will blink to indicate that the
variation has not been registered.
2. Press the enter key to confirm your selection. The digits on the display panel will cease to blink and the projector will now
respond to the new address.
Note: by holding the + or – button down the scrolling will be faster; thus allowing a faster selection
WARNING!
If you alter the DMX address with no DMX signal connected, the digits on the display panel will continue to flash even
after you have pressed ENTER button to confirm the address.

English
13
7.2 DMX functions
7.2.1 FullSpectrum DMX chart
12ch 8ch 4ch
1 1 proportional 0 - 255 0% -100%
2 2 1 red cyan proportional 0 - 255 0% -100%
3 3 2 green magenta proportional 0 - 255 0% -100%
4 4 3 blue yellow proportional 0 - 255 0% -100%
5 5 4 proportional 0 - 255 0% -100%
step 0 - 9 0% -4%
proportional 10 -57 4% -22%
step 58 -59 23% -23%
proportional 60 -108 24% -42%
step 109 -110 43% -43%
proportional 111 -159 44% -62%
step 160 -161 63% -63%
proportional 162 -207 64% -81%
step 208 -209 82% -82%
proportional 210 -255 82% -100%
step 0 - 9 0% -4%
proportional 10 -255 4% -100%
0 - 9 0% -4%
10 -40 4% -16%
41 -71 16% -28%
72 -133 28% -52%
134 -185 53% -73%
186 -199 73% -78%
200 -205 78% -80%
206 -211 81% -83%
212 -217 83% -85%
218 -223 85% -87%
224 -229 88% -90%
230 -235 90% -92%
236 -241 93% -95%
242 -247 95% -97%
248 -255 97% -100%
led control frequency tuning 1500 Hz
LCD display off
led control frequency tuning 4500 Hz
proportional control ofthe color percentage from 0 to 100%
led control frequency tuning 2000 Hz
led control frequency tuning 2500 Hz
led control frequency tuning 3000 Hz
stop strobe
random strobe effect with variable speed from slow to fastand
synchronised colours
random strobe effect with variable speed from slow to fastand
non-synchronised colours
led control frequency tuning 4000 Hz
led control frequency tuning 1000 Hz
stop strobe
led control frequency tuning 3500 Hz
fine dimmer control 16 bit
adjust luminous output intensity from 0 to 100%
variable speed strobing effect, from slow to fast
sequenced pulse effect, slow closing, fast opening
(variable speed pulsing,from slow to fast)
sequenced pulse effect, fast closing, slow opening
(variable speed pulsing,from slow to fast)
proportional control ofthe white percentage from 0to 100%
no effect
stop strobe
600 Hz
no effect
proportional control ofthe color percentage from 0 to 100%
stop strobe
master dimmer
step
proportional control ofthe color percentage from 0 to 100%
strobe
white
RGB standard
CMY simulated
led control frequency tuning 5000 Hz
park
LCD display on
6
8
special functions
8
7
6
dimmer fine
7
dmx channel
decimal
percentage
standard RGB
simulated CMY
type of
control
effe ct

English
14
0 - 9 0% -4%
10 -71 4% -28%
72 -133 28% -52%
134 -195 53% -76%
196 -255 77% -100%
0 - 9 0% -4%
10 -71 4% -28%
72 -133 28% -52%
134 -195 53% -76%
196 -255 77% -100%
0 - 9 0% -4%
10 -71 4% -28%
72 -133 28% -52%
134 -195 53% -76%
196 -255 77% -100%
0 - 9 0% -4%
10 -19 4% -7%
20 -29 8% -11%
30 -39 12% -15%
40 -49 16% -19%
50 -59 20% -23%
60 -69 24% -27%
70 -79 27% -31%
80 -89 31% -35%
90 -99 35% -39%
100 -109 39% -43%
110 -119 43% -47%
120 -128 47% -50%
proportional 129 -255 51% -100%
Ed itio n: 1
Fixture : Reflection LEDko Full Spectrum
NOTE 3: operation to a dimmer monochromatic can be selected from the menu dispaly function.
The color used will be the last taken before the selection.
Date: 01/03/2012
Table name: DMX 512 function
CYAN 2005
RED Red Salmon 40
RED Calcolor Red 60
GREEN Blue Green 93
CYAN Custom Cyan 3
MAGENTA 0044
MAGENTA 90 Calcolor 4790
no effect
no effect
NOT E 2: channels 9-10-11 alternately work in RGB or CMY depending of the selection of channel 8 (10-40 / 41-71 dmx)
step
W HIT E 5000 °K
W HIT E 4500 °K
W HIT E 4000 °K
W HIT E 3200 °K
W HIT E 7000 °K
NOTE 1: macros channels 9-10-11-12 are also obtainable only with the corresponding channels 2-3-4-5
W HIT E 6000 °K
W HIT E 7500 °K
W HIT E 6500 °K
BLUE Primary Blue 80
GREEN Primary Gree n 91
GREEN Turquoise 92
white tone
GREEN Light Green 88
BLUE Medium Blue 83
MAGENTA 60 Calcolor 4760
MAGENTA Skelton Exotic
Sangria 39
adjust proportionally white color temperature from 3200°K to
9000°K
YELLOW Gallo Gold 316
YELLOW Custom Yellow 1
YELLOW Custom Yellow 2
no effect
YELLOW 4307
W HIT E 5 500 °K
W HIT E 9000 °K
W HIT E 8500 °K
W HIT E 8000 °K
CYAN Custom Cyan 1
step
step
no effect
CYAN Custom Cyan 2
step
no effect
no effect
RED Deep Salmon 42
blue tone
yellow tone
BLUE Congo Blue 382
BLUE Blue Indigo 59
no effect
RED Scarlet 24
Table number: 298
cyan tone
magenta tone
9
red tone
12
green tone
10
11

English
15
7.2.2 VariWhite DMX chart
channel functio n
type of
control
effe ct
1master dimmer
proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% -100%
select the primary
W HIT E
color 0 - 9 0% -4%
W HIT E
7000 °K 10 -21 4% -8%
W HIT E
6500 °K 22 -33 9% -13%
W HIT E
6000 °K 34 -45 13% -18%
W HIT E
5500 °K 46 -57 18% -22%
W HIT E
5000 °K 58 -69 23% -27%
W HIT E
4500 °K 70 -81 27% -32%
W HIT E
4000 °K 82 -93 32% -36%
W HIT E
3500 °K 94 -105 37% -41%
W HIT E
3200 °K 106 -117 42% -46%
W HIT E
3000 °K 118 -128 46% -50%
proportional
adjustproportionally white color temperature from 3000°Kto
7000°K 129 -255 51% -100%
step no effect 0 - 9 0% -4%
proportional fine dimmer control 16 bit 10 -255 4% -100%
step no effect 0 - 9 0% -4%
proportional variable speed strobing effect, from slow to fast 10 -57 4% -22%
step stop strobe 58 -59 23% -23%
proportional sequenced pulse effect, slow closing, fast opening
(variable speed pulsing, from slow to fast) 60 -108 24% -42%
step stop strobe 109 -110 43% -43%
proportional sequenced pulse effect, fast closing, slow opening
(variable speed pulsing, from slow to fast) 111 -159 44% -62%
step stop strobe 160 -161 63% -63%
proportional
random strobe effectwith variable speed from slow to fastand
synchronised colour temperature selected 162 -207 64% -81%
step stop strobe 208 -209 82% -82%
proportional
random strobe effectwith variable speed from slow to fastand
non-synchronised colour temperature 210 -255 82% -100%
white to ne
3
dimmer fine
decimal
percentage
step
2
4
strobe

English
16
600 Hz 0 - 9 0% -4%
LCD display off 134 -185 53% -73%
LCD display on 186 -199 73% -78%
led control frequency tuning 1000 Hz 200 -205 78% -80%
led control frequency tuning 1500 Hz 206 -211 81% -83%
led control frequency tuning 2000 Hz 212 -217 83% -85%
led control frequency tuning 2500 Hz 218 -223 85% -87%
led control frequency tuning 3000 Hz 224 -229 88% -90%
led control frequency tuning 3500 Hz 230 -235 90% -92%
led control frequency tuning 4000 Hz 236 -241 93% -95%
led control frequency tuning 4500 Hz 242 -247 95% -97%
led control frequency tuning 5000 Hz 248 -255 97% -100%
Ed itio n: 1
park
Fixture: Reflection LEDko VariWhite
-
Table name: DMX 512 function
NOTE 1: channel 2 macros are available in conjunction with dimmer
10
4%
52%
133
Date: 01/03/2012
Table number: 298
5
special functions
step
-

English
17
7.2.3 White 3200K DMX chart
channel functio n
type of
control
effe ct
1master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% -100%
2spare channel step no effect 0 - 255 0% -100%
step no effect 0 - 9 0% -4%
proportional fine dimmer control 16 bit 10 -255 4% -100%
step no effect 0 - 9 0% -4%
proportional variable speed strobing effect, from slow to fast 10 -57 4% -22%
step stop strobe 58 -59 23% -23%
proportional
sequenced pulse effect, slow closing, fast opening
(variable speed pulsing, from slow to fast)
60 -108 24% -42%
step stop strobe 109 -110 43% -43%
proportional
sequenced pulse effect, fast closing, slow opening
(variable speed pulsing, from slow to fast)
111 -159 44% -62%
step stop strobe 160 -161 63% -63%
proportional random strobe effect with variable speed from slow to fast 162 -207 64% -81%
step stop strobe 208 -209 82% -82%
proportional random strobe effect with variable speed from slow to fast 210 -255 82% -100%
600 Hz 0 - 9 0% -4%
LCD display off 134 -185 53% -73%
LCD display on 186 -199 73% -78%
led control frequency tuning 1000 Hz 200 -205 78% -80%
led control frequency tuning 1500 Hz 206 -211 81% -83%
led control frequency tuning 2000 Hz 212 -217 83% -85%
led control frequency tuning 2500 Hz 218 -223 85% -87%
led control frequency tuning 3000 Hz 224 -229 88% -90%
led control frequency tuning 3500 Hz 230 -235 90% -92%
led control frequency tuning 4000 Hz 236 -241 93% -95%
led control frequency tuning 4500 Hz 242 -247 95% -97%
led control frequency tuning 5000 Hz 248 -255 97% -100%
Ed itio n: 1
3
dimmer fine
4
strobe
5
special functions
Date: 01/03/2012
Table number: 298
step
-
park
Fixture: Reflection LEDko 3200 K
decimal
Table name: DMX 512 function
percentage
10
4%
52%
133
-

English
18
8. Display panel functions
By suitably using all the functions of Reflection LEDko, which can be activated through its display panel, it is possible to change
some of the parameters and to add some functions.
Changing the preset settings made by Coemar can vary the functions of the projector so that it will respond differently to the
controller; therefore carefully read about the functions described here before carrying out any possible selection..
8.1 Quick guide to menu
In order to access the functions, just press the menu button: press the key + or – to scroll pages. To select the desired function,
press enter key.
8.2 Rapid count
By the display panel of Reflection LEDko It is possible to quickly change the various numbers displayed for the different functions
in the following 3 manners:
1.Pressing the + or – buttons will cause the count to be quicker.
2.Pressing first + and then – and then holding them down simultaneously will cause the numbers to jump to the highest value.
3.Pressing first – and then + and then holding them down simultaneously will cause the numbers to jump to the lowest value.

English
19
8.3 Main function menu (FUNC)
The projector gives the opportunity to change and customize some functional settings.
FUNC
DIMM.
Dimmer mode: it can simulate dimmer effect with Tungsten or Xenon
lamp.
TUNG
XENO
ID
It allows to set the ID number of the unit by + and – keys; “enter” key to confirm.
Da 1 a n°
COLR
TEST
DISP
It allows to turn 180° the reading of the display. HOLD
locks the keys. Press any key for 5” to unlock.
RVRS
HOLD
AA/VV
ON/OFF
8 CH
DMX It allows to select the functioning mote at 8 DMX channels without
shade or the extended functioning at 12 channels with selection and
mixing of the shades. The 4 channel features allows to let the
projector to work only with RGB+W channels without dimmer.
4 CH
1 CH It allows to use only the color chosen by dmx and the dimmer.
12 CH
See following sections for details.
8.3.1 FullSpectrum
8.3.2 VariWhite
8.3.3 White 3200K
S.COL
The equipment keeps activated only primary colors RGB/CMY and allows to
make and store custom colors to send to banks of channels 9-10-11
SURE
FullSpectrum Only
D.MAX
RESE
DFSE
Disables the adjusting of the leds setting them at maximum output.
It permits the reset of the unit. Keeping pressed ENTER and MENU at the
turning on of the unit It allows to access ALIG features.
It restores all the settings at default value excepting of led settings and hour
meter.
ON
OFF
enter
SURE
LED
AUTO allows to turn off the display after 6 seconds
AUTO
ON
FRE It allows to set the flickering frequency from 1000 to 5000 Hz besides
the default value. (NOTE: DMX signals goes ahead this setting)
From 1000 to 5000

English
20
8.3.1 TEST/COLOR Functions FullSpectrum
RGB
CMY
Customizing the color preset (S.COL function)
LEDko FullSpectrum has one bank of 24 preset RGB and CMY ”gel” fully customizable by the user in order to obtain a custom gel
palette. To create and store each single custom color, create the favorite color by using DMX desk (RGB channels) then navigate
the FUNC menu until the S.COL item appears. Press enter and by pressing “+”, “-“, “enter” buttons, choose the position in the
memory bank of the unit according to the following diagram; when done, press “enter” and confirm by pressing “enter” one more
time:
It allows to choose the primary colors and to emulate classic CMY
in a wide gamut without DMX signal.
It allows to vary the channel of white on several color temperatures
from 3200 °K to 9000 °K, without DMX signal.
See diagram below.
It allows to turn on the primary colors
without DMX signal.
STORE saves settings for the next
turning on of the projector.
9000 6500
4500
3200
RED
GREE
BLUE
WHTE
0042
0091
0080
0024
0092
0083
0040
0093
0382
0060
0088
0059
CYAN
MAG
YELL
WHTE
CST1
0044
4307
CST2
4790
0316
2005
4760
0018
CST3
0039
CST21
9000
7500
4500
3200
RGB
CMY
COLR
WHTE
GREE/MAG
BLUE/YELL
STRB
RED/CYAN
STORE
TEST
0 - 255
0 - 255
PRESETS
STORE
STORE
GREE
BLUE
1
1
1
2
2
2
3
3
3
4
4
4
CYAN
MAG
YELL
1
1
1
2
2
2
3
3
3
4
4
4
RED
SURE
PRIM
PRIM
PRIM
PRIM
PRIM
PRIM
PRIM
PRIM

English
21
The 24 gel presets bank is organized to allow you to arrange the custom gels in function of the primary color and/or the mixing
method (RGB or CMY). For example, if you are going to store your “blue sky” blue obtained by RGB, it is recommendable to store it
under RGB BLUE in one of the four available positions; if your next storing is a “fire red” obtained by CMY it should be stored in one
of the four available positions under CMY MAG and so on. Once you have customized the bank you can check by scrolling the
COLR menu that the new gels will be named with the numbers of the memory positions (1 to 4).
WARNING ! the operation is irreversible. Once modified, the bank cannot be restored even launching the restore to
default settings function. We recommend to store the factory bank before proceeding by using DR1+ interface ( see
instruction at chapter 8.6.1)
8.3.2 TEST Functions VariWhite
8.3.3 TEST Functions White 3200K
W.TEMP
DIMMER
STROBE
TEST
7000 4000
3200
-Store
0 - 255
0 - 255
TEST
-Store
DIMMER
STROBE
0 - 255
0 - 255
It allows to vary the channel of white on
several color temperatures from 3200 °K
to 9000 °K, without DMX signal.
STORE saves settings for the next
turning on of the projector.

English
22
8.4 Measures and test s(MEAS)
The internal microprocessor of Reflection LEDko allows for several diagnostic and output paramenter to be displayed.
MEAS
It shows the temperatures detected by the probe on the led module:
It shows the volt value of the power of the unit.
It measures the DMX value (0-255) received by each DXM channel of
the unit.
Reading of the typical DMX 512 value called “RATE”
(frequency of signal updating in milliseconds).
It shows the error message of the alarm in progress.
It shows the luminous efficiency of the LEDs (to
FullSpectrum RGBW, to VW and 3200 M1234).
It shows the led’s life values in hours: LIF.R led module life (resettable),
LIFE life of total modules installed on the unit since now (not resettable)
UNIT life of the projector.
It shows the led’s emission frequency. It may be useful if frequency must
be set due to flicker issues.
TEMP
VOLT
DMIN
RATE
ALRM
LED
HOUR
FRE
DIMM: 100%
CH1: 80%
CH2: 30%
CH3: 10%
CH4: 100%
It shows the actual software version installed on the unit.
VERS