Coemar Infinity Wash M User manual

Infinity Wash M
instruction manual
manuale di istruzioni
Version .0
DIS128

∞Infinity Wash M
Serial number/numero di serie
Date of purchase/data di acquisto
Retailer/fornitore
Address/indirizzo
Suburb/cap/città
Capital city/provincial
State/stato
Tel./fax
Please note in the space provided above the relative service information of the model and the
retailer from whom you purchased your Infinity Wash M: this information will assist us in providing
spare parts, repairs or in answering any technical enquiries with the utmost speed and accuracy.
Prendete nota, nello spazio apposite, dei dati relative al modello e al rivenditore del vostro Infinity
Wash M: questi dati ci permetteranno di assistervi con la massima rapidità e precisione.
WARNING: the security of the fixture is granted only if these instructions are strictly follow;
therefore it is absolutely necessary to keep this manual.
ATTENZIONE: la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti
istruzioni, pertanto è necessario conservarle.
User Manual Version .0
edition ^ĞƉƚĞŵďĞƌϮϬϭϭ

English
5
Index
1.Packaging and transportation..............................................................................................................................................................................6
1.1 Packaging.........................................................................................................................................................................................................6
1.2 Trasportation ....................................................................................................................................................................................................6
2. General information .............................................................................................................................................................................................6
2.1 Important safety information. ............................................................................................................................................................................6
2.2 Warranty conditions..........................................................................................................................................................................................7
2.3 EC Norms.........................................................................................................................................................................................................7
3. Product specifications.........................................................................................................................................................................................7
3.1 Technical characteristics...................................................................................................................................................................................7
3.2 Dimensions.......................................................................................................................................................................................................7
3.3 Projector Components......................................................................................................................................................................................8
4. Installation ............................................................................................................................................................................................................8
4.1 Mechanical installation......................................................................................................................................................................................8
4.2 Safety connection.............................................................................................................................................................................................9
5. Powering up..........................................................................................................................................................................................................9
5.1 Connecting to mains power ..............................................................................................................................................................................9
6. Control signal connections................................................................................................................................................................................10
6.1 Connection through ArtNet.protocol................................................................................................................................................................10
7. Turning on the projector....................................................................................................................................................................................11
7.1 DMX address of the projector .........................................................................................................................................................................11
7.2 DMX functions................................................................................................................................................................................................12
8. Display panel functions .....................................................................................................................................................................................14
8.1 Quick guide to menù.......................................................................................................................................................................................14
8.2 Rapid count ....................................................................................................................................................................................................14
8.3 Main functions ................................................................................................................................................................................................15
8.4 Measures........................................................................................................................................................................................................17
8.5 Display setup..................................................................................................................................................................................................17
8.6 Demo mode....................................................................................................................................................................................................18
8.7 Special mode and electronic motor alignment.................................................................................................................................................18
9. Lamp installation and alignment.......................................................................................................................................................................20
9.1 Lamp installation.............................................................................................................................................................................................20
9.2 Aligning the lamp in the optical path................................................................................................................................................................21
9.3 Halogen lamp operations................................................................................................................................................................................21
9.4 Turning back to discharge lamp (700W or 575W) ...........................................................................................................................................22
10. Operating on inside groups.............................................................................................................................................................................23
10.1 How to open the projector.............................................................................................................................................................................23
10.2 How to extract the gobos and colour changer assembly. ..............................................................................................................................23
10.3 Standard color wheel configuration...............................................................................................................................................................24
10.4 How to replace filters ....................................................................................................................................................................................24
10.5 Standard effect wheel configuration..............................................................................................................................................................25
10.6 How to replace effects ..................................................................................................................................................................................25
10.7 Reassembly the groups on the projector.......................................................................................................................................................25
11. Maintenance......................................................................................................................................................................................................26
11.1 Periodic cleaning ..........................................................................................................................................................................................26
11.2 Periodic maintenance ...................................................................................................................................................................................26
11.3 Fuse replacement.........................................................................................................................................................................................26
12. Spare parts........................................................................................................................................................................................................26
12.1 Spare parts...................................................................................................................................................................................................26
13. Error messages ................................................................................................................................................................................................27
14. Frequently asked questions ............................................................................................................................................................................28

English
6
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in the componentry and
in the technology used. We renew our invitation to you to complete the service information form on the previous page. This will assist in providing
prompt and accurate advice from your Coemar service centre, which you can thoroughly trust and to which you can submit any requests for service
or information. Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to
come.
1.Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suffered any damage during the transportation. In case of damage to the
fixture, contact your currier and your supplier immediately by telephone, fax or email, and inform them you will formally notify them in writing
through registered letter.
Packing List
Make sure the packaging contains:
1 the Infinity Wash M projector.
2 the instruction manual.
3 the Cam-Lock support brackets.
1.2 Trasportation
The Infinity Wash M must be transported exclusively in its original packaging or in an appropriate flight case.
2. General information
2.1 Important safety information.
Fire prevention:
1.Infinity Wash M utilizes a Philips MSR 700 Gold Mini Fast Fit or a Philips MSR Gold 575 MiniFast Fit lamp, the use of any alternative lamp might
be risky and will make the warranty of the fixture null and void.
2. Never locate the fixture on any flammable surface.
3. Minimum distance from flammable materials: 0.5m.
4. Minimum distance from the closest illuminable surface: 0.5m.
5. Replace any blown or damaged fuses only with identical ones, both in size and value. Refer to the connection diagram if there is any doubt.
6. Connect the projector to mains power protected by a thermal magnetic circuit breaker.
Preventing electric shock:
1. Presence of high voltage inside of the fixture. Insulate the projector from mains supply before opening or performing any function which involves
touching the inside of the fixture, including lamp replacement.
2. For the connection to the mains, adhere strictly to the guidelines outlined in this manual..
3. The level of technology of Infinity Wash M requires the use of specialised personnel for all service applications; refer all work to your
authorised Coemar service centre.
4. A good earth connection is essential for the proper functioning of the projector. Never connect the fixture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is present.
7. The fixture must never be located in an exposed position, or in areas of extreme humidity.
Protection against ultraviolet radiation(UV):
1. Never turn on the lamp if any of the lenses, filters, or the plastic housing are damaged; their shielding functions will only operate efficiently if they
are in perfect working order.
2. Never look directly in the direction of the lamp when it is operating.
Safety:
1. The projector must always be installed with bolts, clamps, or other fixing devices which are suitably rated to support the weight of the projector.
2. Always use a secondary safety fixing device with chain or steel wire of a suitable rating to sustain the weight of the unit in case of failure of the
principal fixing point.
3. The external surfaces of the unit, at various points, may reach 150°C. Never handle the unit until at least 10 minutes have elapsed since the lamp
was turned off
4. Always replace the lamp if any physical damage is evident.
5. Never install the fixture in an enclosed area lacking sufficient air flow; the room temperature must not exceed 35°C.
6. Wait at least 10 minutes after the unit has been turned off before attempting to replace or remove the lamp. Always use protection gloves while
replacing the lamp.
7. The projector contains electronic and electrical components which must under no circumstances be in contact with water, oil or any other liquid.
Failure to do so will compromise the proper functioning of the projector.
Projector movement.
The projector has a pan range of 540° in its base and a tilt range 262° in its yoke; do not obstruct the projector whilst it is moving.
Forced ventilation
On the body of the projector you will note several air vents housing several cooling fans, both in the basis and in the body. To avoid any problems
associated with overheating, never obstruct any of these vents, as this would seriously compromise the proper operation of the unit.
Protection rating against penetration by external agents:
The fixture is classified as an ordinary apparatus ; its protection grade against penetration by external agents, solid or liquid, is IP20.

English
7
2.2 Warranty conditions
1. The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects.
2. The warranty does not extend to damage caused by inappropriate usage, use by inexperienced operators or inadequate maintenance.
3. The warranty is immediately void if the projector has been tampered or opened by unauthorised personnel.
4. The warranty does not extend to fixture replacement.
5. Both the serial number and the model of the projector are required for any advice or service from your authorised service centre.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.
3. Product specifications
3.1 Technical characteristics
700 W
575 W
Power
90-260 Vac 50/60Hz Autosensing
Maximum current
4,5 A 4A.
Power factor
Cos ϕ= 0,9
Lamp Wattage
700 W
575 W
Maximum room temperature
35°C/95°F
Weight
25 Kg./55 lbs
IP rating
IP20
3.2 Dimensions

English
8
3.3 Projector Components
4. Installation
4.1 Mechanical installation
Infinity Wash M may be either floor or ceiling mounted. It may also be installed on a structure. The unit is provided with four rubber feet mounted
on its base, allowing it to be placed on a flat surface. For installations on a reticular structure, Coemar provides a set of Cam-lock support brackets,
which are included in the packaging. The Cam-lock bracket is one-fourth-turn supports. Before using it for supporting the projector, make sure that it
is correctly seated and firmly tightened into position).
Components description
A
Front lens assembly
B
Zoom assembly
C
Colour changer assembly
D
Lamp assembly
E
Body casing
F Yoke
G
Base casing
H
Base
I
Camlock plate
L
Body
A
B
C
D E
F
G
H
I
L

English
9
For installations on a reticular structure, we recommend using specific “C” hooks, suitable for supporting the weight. Normally, the “C” hooks are
tightened in the central hole of the cam-lock brackets, as shown in the picture below.
WARNING !
Always make sure that both the structure and the fixing devices (screws, clamps etc.)
are suitable for holding the weight of the unit.
The structure must also be sufficiently rigid so as not to move or shake whilst the Infinity Wash M projector moves during its operation. Make sure
that the supporting structure is not subject to torsion.
Do not install the projector in locations readily accessible by unauthorised or untrained personnel who is not aware of these safety instructions.
4.2 Safety connection
If the Infinity Wash M is fixed to a structure, the use of a safety chain is recommended in order to meet the current relevant safety standards. The
safety chain must pass through the holes “A” and then fixed to the structure itself.
If using steel wires or chains which have not been manufactured by Coemar, make sure that they are suitable for holding the weight of the unit.
5. Powering up
5.1 Connecting to mains power
Mains cable characteristics
The mains cable provided is complying with the most recent standards.
NB: In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusively (cable 3X 1,5 ø external 10
mm, rated voltage 300/500V, test voltage 2 KV, operation temperature -40°C +180°C, Coemar cod. CV5311).
Connection to mains power
For connection to mains, use a connector of a suitable rating to sustain the maximum current: 200/208/230/240 Vac 8 amps constant current in
normal operation.
A

English
10
Identify the mains cable which exits the base of the unit and connect as shown below.
WARNING !
• The use of a thermal magnetic circuit breaker is recommended for each projector. Strictly adhere to all regulatory norms.
• Infinity Wash M cannot be powered through Dimmer power units.
• A good earth connection is necessary for the correct operation of the Infinity Wash M. Never connect the projector to main power if
the green/yellow earth cable provided is not correctly connected.
• All cable and plug connections must be carried out by qualified personnel only.
6. Control signal connections
The digital control signal is transmitted to the projector via a two pole cable screened as per international standards for the transmission of DMX512
data. The connection must be serial, utilising connectors XLR3 and XLR5, male and female, located on the base of Infinity Wash M labelled DMX
512 IN and OUT (see diagram)
Control signal connection by XLR3 e XLR5 plugs
Pin 1= GROUND
Pin 2= DATA-
Pin 3= DATA+
Pin 4= NC
Pin 5= NC
When signal arrives from a DMX 512 console with Cannon XLR5 ( 5 poles) pins 4 and 5 must not be connected.
WARNING !
Make sure that screening and conductors are not in contact one another or with the metal housing of the connector.
Pin n# 1 and housing must never be connected to the unit power supply.
6.1 Connection through ArtNet.protocol
The ArtNet protocol allows enabled projectors to operate and to be seen as a normal network device, such as a standard P.C. connected to a
company network.
Infinity Wash M leaves the factory ready to be connected to an ArtNet network without any further settings. Just connect the projector by means of
the specific RJ45 connector located on the side of the DMX connectors and the relative patch to a common HUB Ethernet which will be connected
to an ArtNet controller. Each Coemar projector has its own IP address, therefore it is not necessary to set it when connecting it to the network.
Should it be necessary to modify the IP address for reasons related to the net, each Coemar projector allows customization. In order to modify the
net setting, access the MAIN FUNCTION/PROJECTOR CONTROL MODE/ARTNET ONLY menu ( alternatively, Artnet to DMX) /CUSTOM IP
ADDRESS (see complete menu, art. 8.3).

English
11
7. Turning on the projector
After having followed the preceding steps, proceed with the power supply and turn on the projector via the main power switch.
The display will show a short welcome message and the software version installed on the internal microprocessors:
The projector will perform the reset function on all motors. This operation will last a few seconds, thus allowing the digital control motors to correctly
position themselves. Then the display will turn on in a fixed mode, indicating the correct DMX 512 signal reception.
During the reset function the display will blink for a few seconds…. …then the DMX address of the projector will appear
If the address continues to blink and the “NO DMX SIGNAL” message appears, it means that the DMX signal has not been received. Check the
connection cable and the mixer functioning.
7.1 DMX address of the projector
NB: The following section is valid only in the case where Infinity Spot XL is controlled by the signal DMX 512.
Each projector utilises 18 address channels (16 bit) for its complete operation and is controlled by a DMX 512 signal (for further information, see
section 7.2, DMX functions).
When powered up initially, each projector will show A001, which indicates DMX address 001; a projector thus addressed will respond to commands
of channel 1 to 18 from your DMX 512 controller. A second unit must be addressed as A019, a third as A039 and so on. The operation must be
carried out every Infinity Wash M which has an address different from A001.
Altering DMX address
1. Press the + or – button until the display shows the required DMX address. The digits on the display will blink to indicate that the variation has not
been registered.
2. Press the enter key to confirm your selection. The digits on the display panel will cease to blink and the projector will now respond to the new
address.
NB: by holding the + or – button down the scrolling will be faster; thus allowing a faster selection
WARNING!
If you alter the DMX address with no DMX signal connected, the digits on the display panel will continue to flash
even after you have pressed ENTER button to confirm the address.

English
12
7.2 DMX functions
Note: the default setting is 16 bit/24 channels
1X axis, base movement
(pan) coarse proportional proportional coarse control of the base motor movement 0 - 255 0% -100%
2X axis, base movement
(pan) fine proportional proportional fine control of the base motor movement 0 - 255 0% -100%
3Y axis, yoke movement
(tilt) coarse proportional proportional coarse control of the yoke motor movement 0 - 255 0% -100%
4Y axis, yoke movement
(tilt) fine proportional proportional fine control of the yoke motor movement 0 - 255 0% -100%
step standard (fast)
0 - 10 0% -4%
step
ultra fast movement (best for programming positions) 11 -25 4% -10%
proportional vector mode (from fast to slow)
26 -127 10% -50%
proportional tracking mode (from fast to slow)
128 -247 50% -97%
step smooth mode
248 -255 97% -100%
6dimme r proportional gradual adjustment of luminous intensity from 0 to 100% (see channel 17) 0 - 255 0% -100%
step shutter closed (zap off) 0 - 9 0% -4%
proportional strobe effect with variable speed from slow to fast 10 -66 4% -26%
step shutter open (zap off) 67 -68 26% -27%
proportional
sequenced pulse effect, slow closing, fast opening
(with variable speed from slow to fast)
69 -125 27% -49%
step shutter open (zap off) 126 -127 49% -50%
proportional
sequenced pulse effect, fast closing, slow opening
(with variable speed from fast to slow)
128 -184 50% -72%
step shutter open (zap off) 185 -187 73% -73%
proportional random strobe effect, non-synchronised, variable speed from slow to fast 188 -244 74% -96%
step shutter open (zap off) 245 -255 96% -100%
8zoom proportional
proportional zoom control from narrow 13° to wide beam 26° (2X)
proportional zoom control from narrow 18° to wide beam 42° (3X)
0 - 255 0% -100%
zoom 2X 0 - 128 0% -50%
zoom 3X 129 -255 51% -100%
10 no effect step spare channel 0 - 0 0% -0%
no effect 0 - 10 0% -4%
effect 1 11 -92 4% 36%
effect 2 93 -174 36% -68%
effect 3 175 -255 69% -100%
5
movement speed
step
Note 1: zoom 2X / 3X is selectable from channel 9
dmx
channel
percentag
e
function
type of
control
effect
decimal
7
strobe, shutter
and zap effect
effect wheel selection
11
zoom selection range
9
step

English
13
step no effect 0 - 10 0% -4%
proportional proportional indexing of the effect through 360° 11 -127 4% -50%
proportional
continuous rotation of the effect in a clockwise direction with
proportional control over decreasing speed
128 -190 50% -75%
step stop effect rotation 191 -192 75% -75%
proportional
continuous rotation of the effect in a counter-clockwise direction with
proportional control over increasing speed
193 -255 76% -100%
white beam 0 - 5 0% -2%
color 1 6 - 14 2% -5%
color 2 15 -22 6% -9%
color 3 23 -30 9% -12%
color 4 31 -38 12% -15%
color 5 39 -45 15% -18%
from white to white beam (color 1-2-3-4-5),
proportional positions 46 -127 18% -50%
rainbow effect from fast to slow in an counter-clockwise direction 128 -190 50% -75%
rainbow effect from slow to fast in a clockwise direction 191 -255 75% -100%
14 cyan proportional proportional control of the percentage of cyan color in the light beam
from 0 to 100% 0 - 255 0% -100%
15 magenta proportional proportional control of the percentage of magenta color in the light beam
from 0 to 100% 0 - 255 0% -100%
16 yellow proportional proportional control of the percentage of yellow color in the light beam
from 0 to 100% 0 - 255 0% -100%
no effect
0 - 10 0% -4%
zap effect synchronised with the strobe effect,
speed and mode selected by strobe channel 7
11 -30 4% -12%
zap effect, flicker and speed adjustable,
speed and mode selected by strobe channel 7 31 -249 12% -98%
black-out of the light beam during PAN/ TILT movement, colors wheel
and effects wheel
250 -255 98% -100%
standard dimmer (mechanical)
0 - 10 0% -4%
the mechanical dimmer works in sync with the dimming of the lamp 11 -30 4% -12%
the mechanical dimmer has no effect and is active only that the halogen lamp
(variable color temperature)
31 -249 12% -98%
black-out of the light beam during PAN/ TILT movement, gobos wheel, colors wheel
and effects wheel
250 -255 98% -100%
park, no function 0 - 9 0% -4%
lamp off 10 -29 4% -11%
pan and tilt reset (once only) 30 -65 12% -25%
all motor reset exept black out, pan and tilt (once only) 66 -100 26% -39%
all motor reset exept black out (once only) 101 -135 40% -53%
reset of all the motors (once only) 136 -170 53% -67%
LCD display off 171 -185 67% -73%
LCD display on 186 -199 73% -78%
lamp on 200 -255 78% -100%
Edition: 3
halogen dimmer curve
(effect varies depending upon channel 6 dimmer)
step
17
13
proportional
step
12
indexing effect rotation through 360°
Date: 20/ 06/ 2011
Projector: InfinityWash M
Table name: DMX 512 functions
Table number: 294
Note 5: the lamp on/ off function can only be effected if an opposite level is set
Note 4: turning off the lamp and all reset functions are delayed by 6 seconds to prevent accidental activation
Note 3: the LCD panel may be used to disable the switching off of the lamp via DMX
lamp on/ off and
motors reset
step
18
zap effect
(effect varies depending upon channel 7 strobe)
step
17
colors selection
from the color wheel
Note 2: when using halogen lamp, channel 17 allow the selection of the curve which can be a combination of the characteristic dimming lamp and/ or mechanical dimmer

English
14
8. Display panel functions
By suitably using all the functions of Infinity Wash M, which can be activated through its display panel, it is possible to change some of the
parameters and to add some functions.
Changing the preset settings made by Coemar can vary the functions of the projector so that it will respond differently to the controller; therefore
carefully read about the functions described hereunder before carrying out any possible selection.
8.1 Quick guide to menù
In order to access the functions, just press the menu button: the screen you see hereunder, divided into four sections, will appear; the sections will
be shown cyclically, one by one, every time the + or – button is pressed. To select the desired function, press enter.
8.2 Rapid count
By the display panel of Infinity Wash M It is possible to rapidly change the various numbers displayed for the different functions in the following 3
manners:
1.Pressing the + or – buttons will cause the count to be quicker.
2.Pressing first + and then – and then holding them down simultaneously will cause the numbers to jump to the highest value.
3.Pressing first – and then + and then holding them down simultaneously will cause the numbers to jump to the lowest value.
DISPLAY SETUP
-
allows the management
of:
-brightness
-positive or negative graphic
-backlight shutdown time.
-buttons shutdown time.
-180° reading of the display
MAIN FUNCTIONS: groups the main setup
functions of the fixture: pan/tilt
management, lamp management, fans
management, reset, motors test, ID code,
back to original settings and access to
“SPECIAL MODE “.
MEASURES
-
allows the reading of all
functional settings of the fixture:
temperatures, fans power, DMX channels
values, diagnostics, lamp status and life
and diagnostic version of the installed
software.
DEMO
-
allows the performing of the
demonstration program. 4 different demo
programs are available.
DISPLAY
SETUP
MAIN
FUNCTIONS
MEASURES
DEMO

English
15
8.3 Main functions
The projector gives the opportunity to change and customize some functional settings.
MAIN FUNCTIONS
<<Are you sure ?>>
-Lamp type
-Output frequency
-Reset Temp max
PAN/TILT
CMY SETTING
DIMMER SETTING
FANS MODE CONTROL
LAMP STRIKE DMX
RESET
RECALL DEFAULT
SETTING
ZAP EFFECT ENABLE
ID CODE
TEST MOTORS
PROJECTOR CONTROL
MODE
BALLAST SETTING
-Pan
-Tilt
-Dimmer
-Shutter
-Zoom
-Zoom select range
-Effect wheel
-Effect rotation
-Color wheel
-Cyan
-Magenta
-Yellow
-Zap effect
-Save all
It allows to move and
check every single
motor without using
DMX signal. SAVE
ALL allows to store
the motors position
until next fixture’s
start up.
It allows to choose an alternative colour insertion curve.
It allows to simulate dimming features of a Tungsten lamp or a Xenon lamp.
-NORMAL: fans are controleld by pcb in function of the internal temperature.
-HIGH:fans are always set at full power.
-STANDARD: the on/off state of the lamp’ s controller by DMX signal..
-ON: the lamp remains always on (please, see DMX chart).
It perform the reset function of the fixture.
Keeping pressed ENTER and MENU buttons during reset ,
it will access SPECIAL MODE (see special mode menu).
Restores all the functional settings (excepts for
address, motors, tuning and odometers) to default
values.
Enables or disables the lamp’s “zap”
effect.
Lets you set the ID code of the fixture
by using + or – buttons.
-Standard
-Special
-Tungsten
-Xenon
-Normal
-High
-On
-Standard
-All
-Pan/Tilt only
-Effect Only
-On
-Off
from 1 to #
Default IP address
Custom IP address
Universe address
MAC address
Default IP address
Custom IP address
Universe address
MAC address
It allows to conf
igure
the fixture to be
controlled by
ARTnet protocol.
It allows to control
the fixture setted in
a DMX chain by
ARTnet controller.
-575 W lamp power
-700 W lamp power
-
Hz value
<<Are you sure ?>>
It resets the ballast’s
temperature value.
It allows the complete management of the horizontal and vertical
movements..
See diagram in
at next page
-DMX only
-ARTnet only
-ARTnet to DMX

English
16
The following diagram explains the sub menu for the management of pan eand tilt, regarding the pan/tilt menu item descrive in the diagram at
previous page.
PAN/TILT MOVEMENT
ENABLE
-Clockwise
-Counterclockwise
- 540°
- 400°
-Clockwise
-Counterclockwise
-On
-Off
Pan/Tilt
Tilt only
-On
-Off
-On
-Off
-On
-Off
Pan/Tilt
Tilt only
-On
-Off
-On
-Off
PAN DIRECTION
PAN ANGLE
TILT DIRECTION
OPTO ENCODER
ENABLE
Pan only
Pan only
It inverts the horizontal beam direction, from
left to right or vice-versa by the same DMX
change.
Panoramic working mode that reduces rotating angle from
540° to 400°.
It inverts the vertical moving beam direction,
from upwards to downwards or vice-versa by
the same DMX level change.
It allows to enable or disable the
optical sensors which check the
base’s or the yoke’s position (or
body) and perform the automatic
return if moved accidentally.
It allows to engage or disengage
the pan, the tilt or both movements.
It allows to start up the fixture into a
case or installed on a truss.
CMY SETTING
DIMMER SETTING
GOBOS
IRIS
FANS MODE CONTROL
LAMP STRIKE DMX
RESET
RECALL DEFAULT
SETTING
ZAP EFFECT ENABLE
ID CODE
TEST MOTORS
PROJECTOR CONTROL
MODE
BALLAST SETTING
PAN/TILT

English
17
8.4 Measures
The internal microprocessor of the Infinity Wash M allows for several diagnostic and output parameters to be displayed.
8.5 Display setup
The display setup allows tot une the Infinity Wash M functions according to your needs. The following diagram shows the section features.
DISPLAY SETUP
DISPLAY REVERSE
BACKGROUND
COLOR
DISPLAY TIME OUT
BUTTON TIME OUT
BRIGHTNESS
-Standard
-Reverse
-Standard
-Reverse
-OFF
-# secs. (+/-)
-OFF
-# secs. (+/-)
1~100%
(+/-)
It allows 180° rotation of the display graphics in case of
upside-down installation of the fixture.
It allows visualization in negative or in positive of the display
graphics.
It allows one to decide number of seconds before turning off
the display back light in case of inactivity. OFF value leaves
the backlight always on.
It allows setting up number of seconds buttons must be
pressed in order to activate functions. This function avoid
activation of features if buttons are pressed accidentally.
It allows setting of brightness of display back light..
MEASURES
It shows the temperatures detected by the sensors in the base:
Tdriver, Tsens#1, Tsens#2, Tsens#3.
It measures main power voltage of the fans:
vmain, vboard, vfan1, vfan2, vfan3. Values over 28.5 V must be
considerated as abnormal.
Reading of the DMX value (0-255) received from each channel used by
the fixture on the DMX 512 line.
Reading of the typical value of the DMX signal called “RATE” (signal
update frequency in milliseconds).
It shows possible ongoing alarm messages.
It shows lamp’s status on or with “zap effect” enabled.
It shows fixture’s odometers: lamp life (r): lif e of the lamp (resettable),
lamp life: total life ao the lamps installed (not resettable), unit life:
fixture’s life.
It shows the actual installed software version:
sw LCD master: software installed on to LCD master board.
sw MOTOR slave: software installed on to MOTOR slave board .
TEMPERATURE
VOLTAGE
DMX INPUT MEASURE
DMX RATE
ALARM STATUS
LAMP STATUS
USAGE HOURS
SOFTWARE VERSION
BALLAST MEASURES
It shows the operating information of the ballast:
Lamp type: installed lamp type (575 o 700 W).
Actual power: Instant power in W emitted from the ballast.
T1max, T2max: Max temperatures (resettable) detected by the ballast.
NStsk: lamp’s strike attempts with countdown.

English
18
8.6 Demo mode
Demo mode allows the fixture to perform up to 4 different demonstration programs Infinity Wash M.
8.7 Special mode and electronic motor alignment
WARNING!
This section is for the exclusive use of qualified and experienced personnel.
SPECIAL MODE menu allows access to the electronic motor alignment section and to special functions, like lamp odometer reset, software upload
and download. To enter SPECIAL MODE reach the reset page in the MAIN FUNCTIONS menu, start reset choosing ALL and press simultaneously
enter and menu buttons for about 10 seconds.
WARNING!
The electronic tuning procedure is only possible when the DMX512 signal is on.
The display panel of Infinity Wash M allows the electronic motor alignment of the projector motors in the optical system; this procedure is
performed by Coemar at the factory during the testing: in order to obtain particular effects or in the case of internal components being replaced
(motors, electronic boards, sensors, etc.) it may be necessary to change this setting.
Altering the default settings performed by Coemar may radically alter the functioning of the projector. Carefully read all of the following functions
before trying to perform any operations.
Note: pressing the buttons + and – simultaneously the setting returns to 128 (default value).
DEMO
DEMO FULL
DEMO FIX
DEMO COLOURS
DEMO EFFECT
It performs a demonstrative program with all systems active.
It performs a demonstrative program without pan and tilt
movements.
It performs a demonstrative program using only colour
changer.
It performs a demonstrative program including only effects
features.

English
19
SPECIAL MODE
PAN
TILT
DIMMER
SHUTTER
ZOOM
ZOOM LENS
EFFECT INDEX
EFFECT WHEEL
COLOR WHEEL
CYAN
MAGENTA
YELLOW
EXIT
Pan movement alignment.
Tilt movement alignment.
Dimmer alignment.
Shutter alignment.
Zoom lens alignment.
2nd zoom lens alignment.
Effect wheel alignment.
Radial alignment of the effects located on the
prism wheel..
Colour wheel alignment.
Cyan filter alignment.
Magenta filter alignment.
Yellow filter alignment.
It stores the settings and closes the procedure.
SPECIAL FUNCTIONS
<<Are you sure ?>>
It restores to 0 the resettabile lamp’s electronic
odometer visible also in MEASURES menu. It
must be restored each time the lamp being
changed in order to get a correct reading of
lamp’s life.
<<Are you sure ?>>
<<Are you sure ?>>
<<Are you sure ?>>
<<Are you sure ?>>
It makes the fixture ready to transfer the LCD
software on to the PC.
It make the fixture ready to transfer the MOTORS
software on to the PC..
It makes the fixture ready to receive the MOTORS
software from the PC.
It makes the fixture ready to receive the LCD
software from the PC.
MOTOR
ADJUSTMENT
LAMP HOURS RESET
DOWNLOAD
LCD MASTER
DOWNLOAD
MOT. SLAVE
UPLOAD
LCD MASTER
UPLOAD
MOT. SLAVE

English
20
9. Lamp installation and alignment
Infinity M utilizes a Philips MSR GOLD 700/2 Mini Fast Fit with PGJX28 base lamp.at maximum power of 700 W or a Philips MSR GOLD 575/2
Mini Fast Fit with adequate ballast setting.(menù MAIN FUNCTIONS/BALLAST SETTINGS). These lamps are available as a spare part at your
Coemar’s distributor or service centre.
Lamp
Philips MSR Gold 700/2 Mini Fast Fit Philips MSR Gold 575/2 Mini Fast Fit Q750W 100V TAL halogen
Coemar code
105830
105831
Power range
700 W (full power), 400W (low power)
575 W (full power), 400 W (low power)
750W
Lighting flow
50000 lm
35600 lm
21500lm
Color temp. 7200°K 7400 °K 3200 °K
Base PGJX28
Life
750 h.
200 h
WARNING !
Balast setting and lamp replacement must be done by qualified personnel.
Disconnect the unit from main power prior to attempting lamp’s installation or replacement.
The fixture internal temperature can reach 250° C after 5 minutes, and reach a peak of 350 °C; make sure that the lamp is cold before trying to
remove it. In any case the fixture can be opened only 10 minutes after turning off the lamp.
The lamp is of the mercury vapour type with discharge ignition. This type of lamp operates at high internal pressure, and a slight risk of explosion
exists if the lamp is operated beyond its recommended life. Therefore, we recommend to replace the lamp within the specified lamp life. Always
handle the lamp with care avoiding to touch it with bare hands.
9.1 Lamp installation
1. Use a suitable tool to loosen the 2 fixing screws A of the lamp holder cover at the rear of the projector body.
2. Remove the lamp holder cover “B”.
3. Insert the lamp into the holder and gently rotate it clockwise until it blocks.
4.Una volta in sede, ruotate la lampada in senso orario fino a bloccarla. The lamp used is made of quartz glass and must be handled with care;
always adhere to the instructions provided in the lamp packaging. Never touch the glass directly, use the polythene wrapping provided in the lamp
packaging. DO NOT USE UNDUE FORCE ON THE GLASS.
5. Insert the lamp holder cover in its original position and screw the 2 screws “A” back in.
WARNING !
- Never use undue force if the procedure becomes difficult.
- Never put pressure on the glass of the lamp.
Never touch the glass of the lamp with bare hands.
WARNING !
Each time you replace the lamp, we recommend the following operations.
• realign the lamp in the optical system in order to avoid dichroic filters overheating and consequent effects.
• reset the lamp odometer to obtain reliable information about the residual life of the lamp.
A
B