Cognex DataMan 280 Series User manual

DataMan®280 Series
Quick Reference Guide
2022 February 21
Revision: 6.3.1.51

Precautions
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lConnectivity is possible through the following options:
l24 VDC (+/- 10%) output connection using a UL or NTRL listed
power supply
lPower over Ethernet (PoE) 13 W power supply
Any other voltage creates a risk of fire or shock and can damage the
components. Applicable national and local wiring standards and rules must
be followed.
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lDo not install Cognex products where they are exposed to environmental
hazards such as excessive heat, dust, moisture, humidity, impact, vibration,
corrosive substances, flammable substances, or static electricity.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lDo not expose the image sensor to laser light. Image sensors can be
damaged by direct, or reflected, laser light. If your application requires laser
light that might strike the image sensor, use a lens filter at the corresponding
laser wavelength. For suggestions, contact your local integrator or
application engineer.
2

lThisproduct does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lInclude service loops with cable connections.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThisdevice should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
3

Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical
shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4

Accessories
You can purchase the following components separately. For a list of options and
accessories, contact your local Cognex sales representative.
Lenses
Accessory Product Number Illustration
6.2 mm lens kit that includes:
l6.2 mm optics mount
l6.2 mm lens
lManual lens cap (assembled)
lScrews
DM280-LENS-62
16 mm lens kit with extended optics mount (requires the use of an
extended front cover and high-powered red LED). The kit includes:
l16 mm optics mount
l16 mm lens
lManual lens cap (assembled)
lScrews
DM260-LENS-16
IR 6.2 mm lens kit, 3-position with IR LED includes:
l6.2 mm optics mount
l6.2 mm lens (IR)
lIR Light for 6.2mm (Risk Group Exempt acc. IEC62471)
lManual lens cap (not assembled)
lScrews
DM280-KIT-IR-62
5

Accessory Product Number Illustration
IR16 mm lens kit that includes:
l16 mm optics mount
l16 mm lens (IR)
lIR Light for 16mm (Risk Group Exempt acc. IEC62471)
lManual lens cap (assembled)
lScrews
DMA-KIT-IR-16
High Speed Liquid Lens Module (HSLL) to be used with 6.2 mm lens or
16 mm lens
DMA-HSLL-280
16 mm lens with ImageMax kit that includes:
l16 mm optics mount
l16 mm lens
lHigh Speed Liquid Lens Module (DMA-HSLL-280)
lHigh Powered red LED illumination (DM280-LED-RED-HP)
(Risk Group Exempt acc. IEC62471)
l2-LED half-polarized extended cover (DM260-LENS-16CVR-
P) (Risk Group Exempt acc. IEC62471)
DM280-KIT-IMGMAX
Blue bandpass filter DM150-BP470
Red bandpass filter DM150-BP635
6

Lens Covers and Internal Illumination
Accessory Product Number Illustration
Red LED Light for 6.2 mm Lens (Risk Group Exempt acc. IEC 62471) DM150-LED-RED
White LED Light for 6.2 mm Lens (Risk Group Exempt acc. IEC 62471) DM150-LED-WHT
Blue LED Light for 6.2 mm Lens (Risk Group Exempt acc. IEC 62471) DM150-LED-BLU
High-Powered Red LED Light for 16 mm Lens (Risk Group Exempt acc.
IEC 62471)*
DM280-LED-RED-
HP
High-Powered White LED Light for 16 mm Lens (Risk Group Exempt acc.
IEC 62471)*
DM280-LED-WHT-
HP
Front cover. Use with a 6.2 mm lens only. DM280-CVR-62
Polarized front cover. Use with a 6.2 mm lens only. DM280-LENS-
62CVR-F
Half-Polarized front cover. Use with a 6.2 mm lens only. DM280-LENS-
62CVR-P
7

Accessory Product Number Illustration
Extended front cover. Use with a 16 mm lens only. DM260-LENS-
16CVR
Extended front cover, half-polarized. Use with a 16 mm lens only. DM260-LENS-
16CVR-P
Extended front cover, fully-polarized.Use with a 16 mm lens only. DM260-LENS-
16CVR-F
C-mount adapter, IP40 DM280-CMNT-00
C-mount cover, IP65 DM280-CMNT-CVR
Note: *For maximum light power 24VDC supply is recommended. For more
information, see Illumination Options on page1.
8

Cables
Note: Cables are sold separately.
Accessory Product Number Illustration
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2001-xx (straight, xx specifies length:
2m, 5m, 10m, 15m, 30m)
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2002-xx (right-angled, xx specifies
length: 2m, 5m, 10m)
Ethernet Cable, Robotic X-Coded M12-8
to RJ-45
CCB-84901-2RBT-xx (straight, xx specifies length:
2m, 5m, 10m)
X-Coded to A-Coded Ethernet cable
adapter, 0.5 m
CCB-M12X8MS-XCAC
Power and I/O Breakout Cable, M12-12 to
Flying Lead, 5m
CCB-M12x12Fy-05 (y = straight/angled)
Power and I/O Breakout Cable, M12-12 to
Flying Lead, 5m
CCBL-05-01
Power and I/O Breakout Cable, M12-12 to
Flying Lead
CCB-PWRIO- xx (straight, xx specifies length: 5m,
10m, 15m)
9

Accessory Product Number Illustration
Power and I/O Breakout Cable, M12-12 to
Flying Lead
CCB-PWRIO-xxR (right-angled, xx specifies length:
5m, 10m, 15m)
I/O Module Cable M12-12 to DB15 CCB-PWRIO-MOD-xx (xx specifies length: 2m, 5m)
RS-232 Connection Cable CCB-M12xDB9Y-05
I/O Extension Cable CKR-200-CBL-EXT
10