Cognex DataMan 8072 Verifier User manual

DataMan®8072 Verifier
Quick Reference Guide
2019 October 08
Revision: 6.1.6SR1.5

Precautions
WARNING: LASER LIGHT, DO NOT STARE INTO BEAM: CLASS 2
LASER PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY CAUSE SERIOUS INJURY.
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
2

Product Overview
WARNING:LASER LIGHT, DO NOT STARE INTO BEAM
1 Imager and Lens Optical System
2 Illumination
3 Removable Standoff
4 Trigger (press and release)
5 Lanyard hook
6 Indicator light
7 Communication module insertion point
Status indicators:
lCommunication:
oGREEN = good verification
oRED = bad verification
3

DataMan 8072 Verifier Kits
The DataMan 8072 Verifier is available in the following kits:
Model number Description
DMV-8072V-S-0200 DataMan 8072 Verifier Ethernet Kit with Stand:
- 8072 Verifier
- Standoff
- Ethernet Slide-In
- Ethernet Cable Attachment
- Standard Ethernet Cable
- POE Injector
- Basic Calibration Card
- Stand Accessory
DMV-8072V-S-0100 DataMan 8072 Verifier USB Kit with Stand:
- 8072 Verifier
- Standoff
- USB Slide-In
- USB Cable
- Power Supply
- Basic Calibration Card
- Stand Accessory
DMV-8072V-0200 DataMan 8072 Verifier Ethernet Kit:
- 8072 Verifier
- Standoff
- Ethernet Slide-In
- Ethernet Cable Attachment
- POE Injector
- Basic Calibration
DMV-8072V-0100 DataMan 8072 Verifier USB Kit
- 8072 Verifier
- Standoff
- USB Slide-In
- USB Cable
- Power Supply
- Basic Calibration Card
DMV-8072V-0000 DataMan 8072 Verifier Kit No Slide-In
- 8072 Verifier
- Standoff
- Basic Calibration Card
4

DataMan 8072 verifier and stand-off Ethernet or USB slide-in
Stand accessory Calibration card
5

DataMan 8072V Verifier Accessories
Ethernet Slide-In DMCM-ENETM-00
Serial/USB 2.0 Slide-In DMCM-USB2EN-00
Power Supply for USB 2.0 Slide-In DM100-PWR-000
POE hub CPS-AC-POE1A-US
Stand Accessory DMV-8072V-STAND
Cognex Basic Calibration Card DMV-CCC
DMV-WCC
GS1 Conformance Calibration Card DMV-GS1CC
Validation Protocol DM8072V DMV-VPS-DPM
Cables
USB Cable for USB 2.0 Slide-In, 2.5 m DM8500-USBC-02
Ethernet Cable for Ethernet Slide-In, 5 m DM8000-ECABLE-05
Standard Ethernet Cable CBL-C10E
6

Connecting the Verifier
1. Connect the slide-in to the reader, and tighten the screws to lock the slide-
in.
2. Insert the plug. Slide the cable lock up to the verifier, and twist the cable lock
in place.
Note: Disconnect the DataMan 8072V Verifier from power or remove the battery before inserting/removing
the communication modules.
7

Installation
Installation procedures and specifications are presented in detail in the DataMan
8072 Verifier Reference Manual, which is installed with the DataMan Setup Tool.
From the Windows Start menu, select the following to access the manual: All
Programs > Cognex > DataMan Software vx.x.x > Documentation.
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact
your Cognex Authorized Service Provider (ASP) or Cognex
Technical Support.
CAUTION:All cable connectors are "keyed" to fit the connectors on the
DataMan system; do not force the connectors or damage may occur.
Install Software and Documentation and
Connect the Reader
To configure a DataMan 8072V Verifier, the DataMan Setup Tool software must be
installed on a networked PC. The DataMan Setup Tool is available from the
DataMan support site: http://www.cognex.com/support/dataman.
1. After installing the software, connect the DataMan 8072V Verifier to your
PC.
2. Launch the DataMan Setup Tool and click Refresh.
3. Select your DataMan 8072V Verifier from the list and click Connect.
8

DataMan 8072V Verifier Specifications
Weight 400 g (including grip assembly with battery)
Operating Temperature 0ºC — 45ºC (32ºF — 113ºF)
Storage Temperature 0ºC — 60ºC (32ºF — 140ºF)
Maximum Humidity 95% (non-condensing)
Environemntal IP65
Codes 2-D barcodes: Data MatrixTM (IDMax and IDQuick: ECC200), QR Code
Power Supply
Requirements
USB: bus powered (optionally: external 6W max LPS or NEC class 2 power supply +5V
- +6V DC)
ETH: Class 2 PoE supply IEEE 802.3af (connect only to PoE networks without routing to
the outside plant)
Inrush current peak 5A maximum
Duration: approx. 30μs
Ethernet 10/100 Base-T FULL/HALF DUPLEX, IEEE 802.3
DataMan 8072V Verifier Imager Specifications
Specification DataMan 8072V Verifier Imager
Image Sensor 1/3 inch CMOS global shutter
Image Sensor Properties 3.75 μm square pixels
Image Resolution (Pixels) 1280 x 966
Lens Type 12 mm F:4 S-mount lens
9

LED Wavelengths
The following table shows LED types and the related wavelengths:
LED λ [nm]
RED 660
10