3
Configuring Bill Acceptance &Options
To change the configuration settings:
1. Remove the bill box.
2. Press and release the Service Mode Button. Wait
for the green diagnostic LED to begin flashing two
times.
3. Remove the lower housing – press the release but-
ton on the bottom side of the Vantage and slide the
lower housing out of the bill acceptor Figure 6.
4. The 5 LED’s on lower housing will tell you which
setting is either on or off. Use Figure 5 as a guide to
enable or disable bill acceptance and options. If the
LED light is “on”, the option is turned on. If the LED is
off, the option is turned off.
5.To advance from one page to another, with the
lower housing removed, look at the flashing LED #5.
Press and hold the Service Mode Button on the lower
housing for 7 seconds. 1 blink means you are on
page 1. 2 blinks means you are on page 2 and so on.
Release the Service Mode Button when blinking LED
#5 indicates the page you wish to configure.
6. To save the settings, re-install the lower housing
in the Vantage. Be careful not to press the Service
Mode Button when installing the lower housing as this
will change your settings.
•Coupon Acceptance: Enables or disables ac-
ceptance of all user-loaded coupons. If this is set to
“OFF”, no coupons will be accepted.
•High Security vs. Standard Security Bill Accep-
tance: The Standard Security setting accepts 95+%
of genuine street-grade legal bills. High security mode
is recommended for locations with a higher risk of
frauds
•Bezel Lighting Mode: Use the bill inlet LEDs #3
and #4 on page 2 to select Smart Bezel, Impulse, or
Steady bezel lighting. See fig. 5 and chart below.
•1-Way/2-Way/4-Way: Defines the number of bill
orientation directions that the bill acceptor will accept.
1-Way and 2-Way are face up.
•Level 3 Security: Recommended for higher risk
environments. Provides additional level of security
against stringing and fishing attempts by blocking
access to the bill path.
Figure 4
Figure 5
$1 $5 $10 $20
Bill Inlet LEDs
Bill Inlet LEDs
Bill Inlet LEDs
Bill Inlet LEDs
$1 $5 $10 $20
Bill Acceptance
Configuration Settings
Bill Inlet LEDs
Inlet LED Off:
Option Off (Disabled)
Bill Inlet LEDs
Bill Inlet LEDs
Bill Inlet LEDs
SERV
GRN
Action Mode
Diagnostic
Light
#
1.
Service
OFF
2.
OFF
3.
Config
4.
Sales or
Ready
GRN
x 2
Options Navigation
Scrolls to next set of options
within current Page. Each option
should be configured properly
before moving to the next Page.
Scrolls to next Page of options.
Press &
Hold for
next Page
Press
Once &
Release
5.
SERV
SERV
Service Mode Button
SERV
SERV
GRN
Action Mode
Diagnostic
Light
#
1.
Service
OFF
2.
OFF
3.
Config
4.
Sales or
Ready
GRN
x 2
Options Navigation
Scrolls to next set of options
within current Page. Each option
should be configured properly
before moving to the next Page.
Scrolls to next Page of options.
Press &
Hold for
next Page
Press
Once &
Release
5.
SERV
SERV
Service Mode Button
SERV
LED LED Mode LED Operation
#3 #4
Off Off Smart-4 Upper 4 individual LEDs communicate
$1, $5, $10, $20 acceptance when
enabled by host machine.
On Off Impulse Upper 4 individual LEDs blink in a
runway pattern.
Off On Smart-2 Upper two LED sets (left and right)
communicate $1 or $1&$5 acceptance
when enabled by host machine.
On On Steady Upped 2 LED sets (left and right)
communicate $1 or $1&$5 acceptance.
Lower outside LEDs remain steady on.
To Configure Options
CoConnffiigg
Diagnostic LED
Re-install Lower Housing.
Inlet LEDs flash 5 times
confirming options are saved
Press and release
button, diagnostic
LED flashes
Set Options As Desired
(see Options Navigation and
Configuration Settings figures)
Test unit to ensure proper setup.
Remove Lower Housing
Coupons/Security/Bezel Lights
Bill Acceptance/ Orientation
Level 3 Security
Level 3
Security Reserved Page 4
(Flash x4)
Page 3
(Flash x3)
1-Way 2-Way
4-Way (both on)
Page 1
(Flash x1)
Page 2
(Flash x2)
$50 $100
Coupons High
Security
#3 #4
Inlet LED On:
Option On (Disabled)
ON OFF
