Coleman 9392-162 User manual

Center Port
Hub Hub
B
B
Ridge Pole
–Begin by placing the ridge pole the
desired direction for the shelter
doors and in the center of the
area you will be setting up the
shelter. Note the hubs at each
end and center port. (illus. 1, 2)
Leg Pole Assembly
–Leave the bottom section of each leg
pole unassembled (illus. 4), allowing
for easier set up low to the ground.
–Assemble the Leg Poles (4)
–Insert the end with the spring clip
of Pole (A) into the ridge pole hub
port marked (A) until it clicks into
position. (illus. 3)
–Insert upright pole (B) in the same
manner and to the same end as (A).
(illus. 3, 4)
–Repeat at other end of Ridge Pole.
–Insert Center Poles (Red) into Center
Port. (illus. 5)
16’x12’ Screen Shelter
1
2
WhenYou Are ReadyTo Set
UpYour Shelter
–Select a level area clear of
rocks, branches and other hard or
sharp objects.
–Do not set up your shelter under
trees.
–For easier set up, two or more
people are recommended.
POLE ASSEMBLY PARTS
Instructions apply to Part Number 9392-162
Ridge Pole
Part No. 9392-102
Upright Leg Poles (A)
Part No. 9392-103
Upright Leg Poles (B)
Part No. 9392-104
Center Poles (Red)
Part No. 9392-105
Side Wall Part No. 9392-106
Illus. 5
Leg Poles and
Ridge Pole assembled
into hubs.
Illus. 1
Ridge pole
hub
End
Hub Center Port
Illus. 3
Insert Leg
Poles (A) & (B)
into end hub
of Ridge Pole
Illus. 4
Leg Poles (A) & (B)
insert into one end of
ridge Pole Hub.
Illus. 2 Ridge Pole assembled
Leave bottom section
of leg poles
unassembled.
Leg Pole

3
PRINTED IN SRI LANKA Rev. 10/03
Things You Should Know
• Never store shelter, even for a short period of time, without drying it
thoroughly and brushing off caked dirt.Do not pack stakes or poles inside
your tent.Use separate storage bag provided.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE SHELTER FABRIC OR SHELTER STAKE LOOP TO
REMOVE STAKE.
• SHELTER POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
• Do not leave your shelter set-up for weeks at a time, be aware that expo-
sure to the ultraviolet rays of the sun can seriously damage material and/or
cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES
AWAY FROMTHIS SHELTER FABRIC. This product meets the flammability
requirements of CPAI-84. The fabric will burn if left in continuous contact
with any flame source.The application of any foreign substance to the
fabric may render the flame-resistant properties ineffective.
THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN SRI LANKA
Attach Shelter to Frame
–Drape the shelter over the frame.
–Position each corner over the
curve portion of the pole. (illus. 6)
–Fully extend each leg pole by
completing the interlocking of the
shock corded pole sections.
–Insert the brass hooks into the holes
near the base of each pole. (illus. 7)
–From the inside of the shelter secure
the pole frame to the shelter with the
hook and loop closures.
–Adjust poles to pull the shelter
taut and stake down through
the fabric loops at the end of
each pole. (illus. 8)
–Adjust hook straps to increase
tautness. (illus. 8)
–Attach guy lines to fabric
guy loops at each corner
and stake out. (illus.9)
4Attach Side Wall
–For additional shade attach side wall
using the toggle & loop system inside
the shelter and on the side wall. (illus. 10)
–The side wall can be easily moved for
more shade throughout the day.
illus. 6 Fabric draped over
partially assembled frame
illus. 7
Insert Brass Hook
into hole near the
base of the pole
illus. 9
Completed
Screen Shelter
with guy lines
illus. 8
Stake through
Stake Loop
Hook Strap
Use to adjust or
tighten canopy
illus. 10 Completed Screen
Shelter with attached side wall
Stake
Stake
Loop