Coleman 9391-122 User manual

Peak Pole Assembly
–Assemble and connect one
Peak Pole (lighter colored) at a
time to the hub pole. (illus. 1, 2)
Frame and Leg
Pole Assembly
–Only the bottom 2
sections of the Leg Pole
should be assembled (illus. 3),
allowing for easier set up low to
the ground.
–Assemble the Ridge Poles (4)
–Insert the end with the spring clip
into one of the Upright Leg hub
ports until it clicks into position.
(illus. 4).
–Repeat for all Ridge poles (illus. 3)
–Attach Peak Poles by inserting the
end with the spring clip into the
center slot of the Upright Leg hub
ports until it clicks into position.
(illus. 5, 6)
–Repeat for each of the 3 remaining
poles. (illus. 5, 6)
12’x12’ Shade House
1
2
WhenYou Are ReadyTo Set
UpYour Shelter
–Select a level area clear of
rocks, branches and other hard or
sharp objects.
–Do not set up your shelter under
trees.
–For easier set up, two or more
people are recommended.
POLE ASSEMBLY PARTS
Instructions apply to Part Number 9391-122
Hub Part No. 9191-126
Peak Pole Part No. 9191-125
Upright Leg Pole
Part No. 9191-123
Ridge Pole
Part No. 9191-124
Illus. 6
Peak Poles and Ridge
Poles assembled into
Upright Leg hub.
Illus. 1
Peak Poles
inserted
into hub
Hub
Illus. 2
Peak Poles
inserted
into hub
Illus. 4
Ridge Poles inserted
into hub of Upright Leg
Illus. 5
Peak Pole inserted into center
of hub of Upright Leg
Illus. 3
Ridge Poles inserted into
hub of Upright Leg. Upright
Leg not fully assembled.
Pole
Leg
Pole
Ridge Pole
Hub

illus. 10
Completed shelter with guy lines
3
PRINTED IN SRI LANKA Rev. 10/03
Things You Should Know
• Never store shelter, even for a short period of time, without drying it
thoroughly and brushing off caked dirt.Do not pack stakes or poles inside
your tent.Use separate storage bag provided.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE SHELTER FABRIC OR SHELTER STAKE LOOP TO
REMOVE STAKE.
• SHELTER POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
• Do not leave your shelter set-up for weeks at a time, be aware that expo-
sure to the ultraviolet rays of the sun can seriously damage material and/or
cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES
AWAY FROMTHIS SHELTER FABRIC. This product meets the flammability
requirements of CPAI-84. The fabric will burn if left in continuous contact
with any flame source.The application of any foreign substance to the
fabric may render the flame-resistant properties ineffective.
THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN SRI LANKA
Attach Shelter to Frame
–Drape the shelter over the frame
–Position each corner over the
curve portion of the pole. (illus. 7)
–Fully extend each upright pole by
completing the interlocking of the
shock corded pole sections.
–Insert the brass hook into the hole
near the base of the pole (illus. 8)
–From the inside of the shelter secure
the pole frame to the shelter with the
hook and loop closures.
–Adjust poles to pull the shelter
taut and stake down through
the fabric loops at the end of
each pole (illus. 9)
–Adjust hook straps to increase
tautness (illus. 9)
–Attach guy lines to fabric
guy loops at each corner
and stake out (illus.10)
illus. 7 Fabric draped over
partially assembled frame
illus. 9
Stake through
Stake Loop
Hook Strap
Use to adjust
or tighten
canopy
illus. 8
Insert Brass Hook
into hole near the
base of the pole
Stake
Stake Loop