Coleman AMERICAN HERITAGE WEATHERMASTER 2000000148 User manual

AMERICAN HERITAGE
™
WEATHERMASTER®CABIN 12'X9'
1Layout & Positioning of Tent
– Layout and position tent with door
facing desired direction. (illus. 1)
– Stake down tent, starting with
the corners. Do not stretch
too tight. Angle the stakes
slightly toward the tent.
(illus. 2) Keep the floor taught.
– Unzip the door.
2Assemble & Place Roof Poles
– Assemble all shock-corded
roof poles. When assembled will
form a continuous arch with both
ends pointing down. (illus. 3)
– Insert the curved ridge roof pole
through center roof pole sleeve.
(illus. 4)
– Insert the curved End roof poles
through end roof pole sleeves.
(illus. 4)
When You Are Ready
To Set Up Your Tent
– Select a level campsite clear
of rocks, branches and other
hard or sharp objects.
– Do not set up your tent
under trees.
– For best results in windy
conditions, position the end
of tent into the wind.
(1) Center Curved Roof Poles
(Red Sticker) Part No. 5010000474
(2) Rear Curved Roof Poles
(Green Sticker) Part No. 5010000475
(2) Center Adjustable Upright Poles
(Red Sticker) Part No.
5010000477
(4) Rear Adjustable Brace Poles
(Green Sticker) Part No.
5010000476
Rainfly Part No. 5010000478
Instructions apply to Part Number 2000000148
illus. 3 Curved roof pole assembly.
illus. 4 Curved roof pole system shown
inserted through pole sleeves. (3 total)
illus. 2
Stake loops
properly staked
Front door
Roof sleeve
illus. 1
Pole sleeves
Shock-corded poles
Forms an arch
POLE ASSEMBLY PARTS
Hinged Door Pole
Part No. 5010000513
Vertical Hinged Door Pole
Part No. 5010000512

Rainfly guylines
Rainfly
illus. 9
Tent shown completely
set-up. Note the different
angles of the end poles.
Brace pole with hole
for rainfly
“S” hooks
3Raise Center of Tent
– Assemble center adjustable poles
(red sticker, longer poles). Pole should be initially
adjusted to the inner most hole “A”. (illus. 7)
– Insert square end of brace poles into curved roof
poles and raise tent upright. (illus. 5, 6, 7)
– Adjustable poles should attach to squeeze
pins at bottom of tent. (illus 8)
– Repeat for other center adjustable pole.
4Raise Sides of Tent
– Assemble shock-corded adjustable end poles.
– Insert brace poles into end curved roof poles.
MAKE SURE when attaching the brace poles to
the curved poles that the bottom of the brace pole
naturally points down and toward the center of the
tent. (illus. 9)
– End poles should attach to squeeze
pins at bottom of tent. (illus. 8)
– Drape rainfly over tent and attach “S”
hooks on rainfly into holes in brace
poles. (illus. 9)
– Assemble and insert (short) Vertical
Hinged Door Pole through vertical sleeve
and into bottom pole stop. Gently apply
pressure to insert top end into top pole stop
and zip sleeve closed. (illus. 9, 10)
– Assemble and insert (long) Hinged Door
Pole through curved door sleeve and into
top pole stop. Gently apply pressure to insert
bottom end into bottom pole stop and zip
sleeve closed. (illus. 10, 11)
– Attach guylines to the ends of the
rainfly, 3 guylines at each end, and
stake out. (illus. 9)
illus. 5
Shown with center
brace poles in position
and curved poles
through pole
sleeves.
illus. 6 When attaching the brace poles to
the curved poles make sure that the brace
poles naturally point straight down.
Brace pole
Curved
poles in
pole sleeve
THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA
PRINTED IN CHINA Rev. 11/07
Things You Should Know
•Under certain conditions (cold weather, high humidity, etc.) condensation will form on
the inside surfaces of your tent. Condensation is caused by water vapor from your
breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the
tent fabric. It can be minimized by removing wet clothing from your tent and by
providing good ventilation through the tent.
•Never store tent, even for a short period of time, without drying it thoroughly and
brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate
storage bag.
•STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER
PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE.
•TENT POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
•Do not leave your tent set-up for weeks at a time, be aware that exposure to
the ultraviolet rays of the sun can seriously damage material and/or cause it to
become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC. This tent meets the flammability requirements
of CPAI-84. The fabric may burn if left in continuous contact with any
flame source. The application of any foreign substance to the tent
fabric may render the flame-resistant properties ineffective.
illus. 8
Insert squeeze
pin into pole
Stake down
doormat
illus. 7 Poles should be initially
adjusted to the inner most hole “A”.
illus. 10 Hinged Door
Pole Stop illus. 11 Hinged Door
Long Door
Pole inserts
into sleeve
and pole
stops, then
zips in.
Vertical Door
Pole inserts
into sleeve
and zips in
End guylines