Coleman DURANGO 2000000143 User manual

DURANGOTM 15’ X 10’ MODEL 2000000143
STITCH LINE
Fig. 1
Fig. 7
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door.
2. Stretch out corners and sides of tent. Secure with stakes
driven in at an angle to better anchor the tent. (Fig. 1 & 2)
Note: Staking the corners and sides will make it easier to
raise and tear-down the tent.
7. Insert one end of each black pole
into pins located on the ring in
center location at the back of the
tent. (Fig. 7)
8. Insert other end of black poles
into pins at front corners of tent;
and end of gray pole into pins on
sides of tent to form arches as
shown. (Fig. 8)
Fig. 8
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Parts and Components
Description Part Number
Main Poles, Black (2) 9163-1051
Side Pole, Gray (1) 9163-1061
Roof Ridge Pole, Black (1) 9163-1071
Rainfly Pole, Black (1) 9163-1081
Rainfly 9163-1091
3. Assemble roof ridge pole (3-section, black, shock-corded
pole) and insert through sleeve in center of tent.
4. Place one end of roof ridge pole in brass grommet. Carefully
apply pressure on pole to allow other end of pole to bow and
be inserted into other brass grommet. (Fig. 3 & 4)
Fig. 2
Fig. 3 Fig. 4
5. Assemble the 2 long, black shock-corded poles and insert
through sleeves in top of tent forming an “X” as shown.
(Fig. 5)
Fig. 5
6. Assemble gray, shock-corded, side pole and insert through
sleeve in front of tent as shown. (Fig. 6)
Fig. 6
First
Black Pole
Gray
Pole Gray
Pole
Second
Black Pole
9. Attach frame clips along tent seams to gray side pole and
both black poles. (Fig. 9 & 10)
Fig. 9 Fig. 10
To Attach Rainfly
1. Drape rainfly over tent. Make sure end with logo is centered
over the door and the rainfly seams are centered over the
gray and black
poles. (Fig. 11) Fig. 11
(continued on
other side)

Attaching Room Divider
1. Room divider panel can be installed by inserting toggles
through the fabric loops. (Fig. 19 & 20)
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2006 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. Never pull on
the tent to remove stake.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The fab-
ric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
To Attach Rainfly continued
2. Clip hooks on elastic
cords on rainfly to rings
at bottom of tent. (Fig. 12)
Fig. 16
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Cooler Access
The smaller zippered opening at the side of the tent is designed
for added ventilation and easy access to your beverage cooler.
1. To use as a vent, unzip flap to
expose screen. (Fig.18)
2. To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig.23) Fig. 23
Fig. 20
Fig. 19
STITCH LINE
Electrical Cord Access
1. Unzip access panel in the lower
right corner of tent and bring in
electrical cord. Use only UL
approved cords that are rated for
outdoor usage. (Fig. 22)
Fig. 22
Fig. 12
3. Secure rainfly with hook & loop
fasteners located on underside of fly
to gray and black poles. (Fig 13)
Fig. 13
Fig. 15
4. Assemble black, shock-
corded, rainfly pole
and slide through sleeve
on underside of rainfly.
(Fig 14)
5. Insert ends of rainfly
into brass grommets on
tent to form an arch
over doorway. (Fig. 15)
Fig. 14
COMPLETED TENT
Overhead Storage
1. Convenient overhead stor-
age compartment is located
at the back of the tent.
(Fig. 21)
2. Small storage pockets are
located on each side of tent.
6. Tie guylines at 4 locations (2 on
front, 2 on back) of tent and secure
with stakes.
(Fig. 16 & 17) Tie Guylines
Tie Guylines
Fig. 17
7. To open door fully, unzip, then roll up
and insert toggle through fabric loop.
(Fig. 18)
8. To use the door vent, undo other
zipper to expose vent, then roll up
door flap and fasten with toggle and
fabric loop.
Fig. 18
Fig. 21
Rev09/07