Coleman BackHome Select 9392-136 User manual

BackHome®Pavilion
11’3”x11’3”
Instructions apply to Part Number 9392-136
Things you should know:
Read all instructions before set-up.
Pavilion can be staked down or bolted down.
Initial frame set-up may be done upright or upside down.

Dual Track w/ End Cap
Part: B2 (Qty.: 2)
Part No.: 9392-2531
Dual Track w/out End Cap
Part: A1 (Qty.: 2)
Part No.: 9392-2501
Dual Track w/out End Cap
Part: A2 (Qty.: 2)
Part No.: 9392-2511
Fluted Columns w/ End Caps
Part: C (Qty.: 4)
Part No.: 9392-2541
Dual Track Corner Brace – Small
Part: D (Qty.: 4)
Part No.: 9392-2551
Dual Track Corner Brace – Large
Part: E (Qty.: 4)
Part No.: 9392-2561
Center Hub
Part: G (Qty.: 1)
Part No.: 9392-2581
Corner Brackets
Part: J (Qty.: 4)
Part No.: 9392-2611
Planter Hooks
Part: K (Qty.: 4)
Part No.: 9392-2621
Track/Column Brace
Part: F (Qty.: 8)
Part No.: 9392-2571
Corner Roof Pole
Part: H (Qty.: 4)
Part No.: 9392-2591
Side Roof Pole
Part: I (Qty.: 4)
Part No.: 9392-2601
Dual Track w/ End Cap
Part: B1 (Qty.: 2)
Part No.: 9392-2521
2
Parts List

Decorative Plates
Part: L (Qty.: 4)
Part No.: 9392-2631
Mounting Plates
Part: M (Qty.: 4)
Part No.: 9392-2641
Allen Wrench/
Phillips Screwdriver
Included
Other Suggested Tools:
Power screwdriver with
Phillips Head attachment
For more permanent
mounting, utilize the
appropriate anchor bolts
for your particular
application (not provided).
Canopy – (Qty.: 1)
Part No.: 9392-2651
Privacy Walls (Qty.: 4)
Part No.: 9392-2661
Tie Backs (Qty.: 4)
Part No.: 9392-2691
Phillips Head Machine
Screws – Large (Qty.: 46)
Part No.: 9392-2701
Note: Extra fastener are included for your convenience.
Phillips Head Machine
Screws – Small (Qty.: 26)
Part No.: 9392-2711
Phillips Head Sheet
Metal Screws – Small
(Qty.: 75)
Part No.: 9392-2721
Long Hex Head Cap
Screw (Qty.: 21)
Part No.: 9392-2731
Acorn Nuts (Qty.: 51)
Part No.: 9392-2741
Track Hooks
(Qty.: 101)
Part No.: 9392-2751
Screen Walls (Qty.: 4)
Part No.: 9392-2671
Roof Vent Cover (Qty.: 1)
Part No.: 9392-2681
Stakes
(Qty.: 32)
Part No.:
9392-2761
3

Sort Dual Track Pieces: Layout so that the tracks are all going the the same direction.
A1 (male) matches to A2 (without end cap) and B1 to B2 (with end cap).
Add track hooks. Insert 12 hooks
per track per frame side (24 hooks
each side). It will be easier to
attach the side walls if the hooks
are inserted with the opening to the
grooved side of the track. (illus. 2)
Connect the matching Dual Track pieces A1 to A2 and B1 to B2 and secure with 4 Phillips Head Sheet
Metal Screws – Small. Track Side should be facing the same way on both pieces. Repeat for all other
Dual Track sections.
illus. 1
illus. 2
illus. 3
Set Up Instructions
Phillips Head Sheet Metal Screws _ Small
4

Attach the Dual Track sections to the Columns with the Long Hex Cap Screws (16) by
lining up the pre-drilled holes and hand tightening the screws. There are screw holes on
two sides of the column, make sure that one set of screw holes is facing out and one set
is pointing up. DO NOT FULLY TIGHTEN. Assembled Dual Track A sections will go on
opposites side from each other. (see illus. 5)
Dual Track side with hooks
End cap
Long Hex
Cap Screw
B1&B2 B1 & B2
A1 & A2
A1 & A2
illus. 4
illus. 5
Notice that A and B sections are both opposite each other. Leave frame hand tightened
only at this point.
5

Dual Track Corner Brace – Small (D)
Attach the Small corner brace to the
column with 2 Phillips Head Machine
Screws – Small.
From the outside of the frame insert 4
Phillips Head Machine Screws – Large
through the Dual Track and Small
Corner Brace and secure with 4
Acorn Nuts. (illus. 6)
Repeat for other 3 corners.
Dual Track Corner Brace – Large (E)
From the outside of the frame insert 4
Phillips Head Machine Screws – Large
through the Dual Track and Small
Corner Brace and secure with 4
Acorn Nuts. (illus. 7)
Repeat for other 3 corners.
Track/Column Brace (F)
Position the Track/Column Brace (F)
on the inside of the Dual Track and the
outside of the Column. Secure to the
Column with Phillips Head Machine
Screw – Small. Insert Phillips Head
Machine Screw – Large through the Dual
Track from the outside and attach Acorn
Nut on open end. Repeat for second
Track/Column Brace on other side of
corner (illus. 8).
Repeat for other 3 corners.
illus. 6
illus. 7
illus. 8
(E)
(D)
(F)
Phillips Head Machine
Screws – Large
Phillips Head Machine
Screws – Small
Phillips Head
Machine
Screws – Small
Note: Brace attaches to the inside of the dual track
and to the outside of the column.
Phillips Head Machine
Screws – Large
Phillips Head Machine
Screws – Large
6

Tool tighten all the Long Hex Head Cap
Screws connecting the Dual Tracks and the
Columns. Tool tighten all bolts and nuts.
Completed frame upside down. (illus. 9)
Flip frame upright. Requires 2 to 4 people
Note: Frame can be assembled in upright
position from the beginning if preferred.Simply
follow the same directions, but note that the
illustrations to this point are upside down.
(illus. 10)
Center Hub (G)
Corner Roof Pole (H)
Side Roof Pole (I)
Attach the 4 Corner Roof Poles (H)
and the 4 Side Roof Poles (I) by
inserting the button end into the Hub
until it locks into position.
Alternate Corner Roof, Side Roof,
Corner Roof...until the Hub is
complete. (illus. 11)
illus. 9
illus.10
illus.11
(G)
(H) (I)
7

Roof Vent Cover
Drape the Roof Vent Cover over
the Hub positioning the peak over
the center on the Hub.
Lift the corner of the Roof Vent
Cover and pull over the short
end of the Corner Roof Pole to
insert the pole into the underside
corner pocket. Repeat for all
corners. (illus. 12)
Corner Brackets (J)
Insert the Corner Roof pole end into
the end of the Corner Bracket until in
locks into position. (Illus. 13)
Repeat for all Corner Roof Poles.
Planter Hooks (K)
Insert end with pop up button into
open end of the Corner Bracket.
(Illus. 14)
Repeat for all corners.
Canopy
Drape Canopy over Hub assembly.
Pull the corners out over the Corner
Roof Pole, Bracket and Planter
assembly end and insert in corner
pocket on Canopy. (Illus. 13 & 15)
Repeat for all corners.
Underneath, attach hook & loop
fastener to the Roof Vent Cover
mesh. (illus. 15)
(J)
(K) (J) (H)
(H)
(H)
(H) (I)
Hook & Loop fastener
illus.12
illus.13
illus.14
illus.15
8

The Corner Brackets (J) on the
roof assembly will fit over and
around the corner of the frame
assembly. (illus. 16 & 17)
From inside, underneath the roof
assembly, gently lift the Side Roof
Pole (I) and insert the end tab into
the slot in the center of the Dual
Track section. Repeat for each side.
Then secure into position with the
Phillips Head Sheet Metal Screw-
Small. (illus. 16 & 18)
Use the Phillips Head screwdriver
end of the Allen Wrench to insert
the Phillips Head Sheet Metal
Screw – Small, into the opening on
the Planter Hook and attach to the
Column. (illus. 16 & 19)
Repeat for all corners.
On the underside
of the Canopy pull
the elastic down
and hook into the
ridge on the
outside of the Dual
Track frame.
(illus. 16 & 20)
Lift the roof assembly up into position
over the frame.
Requires two or more people.
illus.16
illus.17
illus.18
illus.19
illus. 20
9

Decorative Plate (L) and Mounting Plate (M)
Lift the Column leg slightly and insert it through Decorative
Plate opening.
Lift the Column leg slightly and insert the Mounting Plate.
Four vertical tabs will go into the Column.
(illus. 21)
Repeat for all Columns and Decorative Plates.
Mounting Plate (M)
Line the holes on the Mounting
Plate tabs up with the pre-drilled
screw holes on the Column.
Secure with 4 Phillips Head
Sheet Metal Screws – Small
(illus. 22)
Repeat for all Columns and
Mounting Plates.
Stake Down
Insert the Stakes through the
4 outer holes.
For more permanent
attachment, you can use
screws or bolts (not included)
instead of the stakes to
secure to a deck or patio.
Repeat for all Mounting
Plates.
illus. 21
illus. 22 illus. 23 illus. 24
(L)
(M)
10
Decorative Plate cover (L)
Slide the Decorative Plate
down to cover the
Mounting Plate.
Repeat for all Columns.