Coleman MEADOW FALLS 2000001390 User manual

4. Insert one end of each
black pole into pins in
front corners of tent.
(Fig. 2)
5. Go to opposite end of
each pole and gradually
apply pressure to the pole
forming an arch. Insert
the pin into the pole end
at the corners of tent.
(Fig. 3)
6. Attach frame clips along
edgesof tent to black
main poles. (Fig. 3A)
7. Stretch corners and sides
of tent until floor is taut
then hammer stakes
through loops to secure.
(Fig. 3B)
STITCH LINE
MEADOW FALLSTM LONG FLY 10’ X 10’
MODEL 2000001390
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Fig. 2
To Set Up Tent
1. Unfold tent and spread out on a clean,
level surface with the door facing the
desired direction. (Fig. 1)
2. Assemble two main tent poles by inter-
locking the longer, black shock-corded,
poles.
3. Insert both, long, black poles through
sleeves in top of tent as shown. (Fig. 1)
Fig. 3
Parts and Components
Description Part Number
Main Poles, Long, Black (2) 5010000380
Ridge Pole w/rubber tips, Black (1) 5010000381
Rainfly 5010000490
1. Assemble the black interlocking shock-corded ridge pole with
rubber tips.
2. Unfold rainfly. Locate the web pockets on front and back of rainfly,
and the hook & loop fasteners on the underside of rainfly.
3. Insert rubber-tipped ends of ridge pole into web pockets located
on both sides of underside of the rainfly. (Fig. 4)
4. Locate hook & loop fasteners on the rainfly
and wrap around black ridge pole to secure.
(Fig. 4A)
To Attach Rainfly
(continued on other side)
Fig. 1
Door
Long, Black,
Shock-corded
Main Poles
3A
3B
Web
Pocket
Black Ridge Pole Fig. 4
4A
Black Ridge
Pole

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Attach Rainfly continued
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
11/07
5. Turn rainfly over and drape over tent
making sure ridge pole is centered
over the door. (Fig. 5)
NOTE: When positioned properly,
seams on rainfly will always align with
poles on tent.
6. Attach hook & loop fasteners,
located on seams of the underside of
rainfly, around the four black main
poles, to secure. (Fig. 5A)
7. Clip hooks on elastic cords, on the
front corners of rainfly, onto metal
loops at front and back corners
of tent. (Fig. 5B)
8. Tie guylines through loops on web
straps on the rainfly. (Fig. 5C)
9. Stretch guylines until taut, then secure
with stakes. (Fig. 5D)
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Electrical Cord Access
1. Unzip access panel in the lower
right corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 8)
Fig. 8
Fig. 5
Cooler Access
The smaller zippered opening at the
rear of the tent is designed for added
ventilation and easy access to your
beverage cooler.
1. To use as a vent, unzip flap to
expose screen. (Fig.6)
2. To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig.7)
Fig. 6
Fig. 7
5D
5A
Black Main
Pole
5B
5C