Coleman HIGHLINE 2000001091 User manual

STITCH LINE
HIGHLINETM TENT 12’ X 12’ MODEL 2000001091
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with
the door facing the desired direction. (Fig. 1)
2. Assemble all poles by interlocking the shock-corded,
sections together. (See components section above for
list of poles.)
3. Insert gray main poles through the sleeves on both
sides of tent; then insert black main poles through
sleeves, in front and back of tent. Make sure black poles
overlap the gray poles. (Fig. 1)
4. Insert end of each black & gray main pole into pins .
(Fig. 2 & 2A)
5. Go to opposite end of each pole and gradually apply
pressure to each forming arches. Insert the pin into each
pole end at the sides and corners of tent. (Fig. 2 & 2A)
6. Attach frame clips along edges of tent to the black &
gray main poles. (Fig. 2B)
7. Stretch tent until taut, then secure metal loops located
on both sides and corners of tent with stakes. (Fig. 2C)
Parts and Components
Description Part Number
Main Poles, Black (2) 5010000433
Main Poles, Gray (2) 5010000506
Vestibule Pole, Long, Thin, Black (1) 5010000507
Rainfly Ridge Pole, Thin, Black w/ Metal Tips (1) 5010000434
Rear Awning Pole (1) 5010000508
Rainfly 5010000435
To Attach Rainfly
1. Insert rainfly ridge pole with metal tips through sleeve
in underside of rainfly. (Fig. 3)
2. Drape rainfly over tent with rainfly ridge pole centered
from above front door to back of tent & the green
vestibule flaps located in the front. (Fig 4).
3. Insert rainfly ridge pole into metal grommet on front of
tent, apply pressure until pole forms an arch, then
insert other end into back grommet. (Fig. 4 & 4A).
NOTE: Because of the position of the center
grommets, it may be necessary to gently pull to
on the front & back arches for easier access.
4. Insert vestibule pole through sleeve in rainfly at front
of tent. (Fig. 4)
5. Locate all hook & loop fasteners on underside of
rainfly and wrap around black and gray poles to secure.
(Fig. 5)
6. Stretch elastic straps and hook clip on each to the
metal loops at the four corners of the tent. (Fig. 6)
Fig. 3
(continued on other side)
Fig. 1
Door
Gray, Main Poles
Side Sleeve
Fig. 2
Rainfly
Sleeve in Rainfly
Fig. 4
Metal Tip
Green Vestibule Flaps
2A
2B
Door
Thin, Black,
Rainfly
Ridge Pole
Black,longer,
Main Poles
Side Sleeve
Front & Back
Sleeves
4A
Door
Fig. 5 Fig. 6
2C
Sleeve in
Rainfly
Vestibule
Pole

Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Electrical Cord Access
1. Unzip access panel in the lower
left front corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 11)
Fig. 11
11/07
To Attach Rainfly continued
7. Insert one end of vestibule pole into pin on front corner of tent. (Fig. 7 & 7A)
8. Go to opposite end of vestibule pole and gradually apply pressure to form an arch. Insert the pin into end
of pole at opposite corner of tent. (Fig. 7 & 7A)
Fig. 10
Fig. 9
Cooler Access
The smaller zippered opening at the
side of the tent is designed for added
ventilation and easy access to your
beverage cooler. (Fig. 12) Fig. 12
Fig. 7
7B
7A
7C
9. Clip hooks on elastic cords on front of rainfly to the metal loops at each corner (Fig. 7 & 7B)
10. Extend out vestibule flaps and secure with metal stakes through the loops in the web straps (Fig. 7 & 7C)
11. Insert the rear awning pole through the sleeve in rainfly above the back window and insert one end into grommet. (Fig. 8 & 8A)
12. Apply pressure to the rear awning pole to form an arch then insert
opposite end into metal grommet on other side. (Fig. 8 & 8A)
13. Tie guylines through loops on web straps on the rainfly. (Fig. 9)
14. Stretch guylines until taut, then secure with stakes. (Fig. 10)
Fig. 8
8A
Grommet
Back Window
Rear Awning Pole
Sleeve in
Rainfly