Coleman Peak 1 9805-230 User manual

Connect Frame to Tent
– Insert one Pole Tip into the grommet on the
webbing located at the corners of the tent (illus. 4).
– Go to opposite end of the same pole and
gradually apply pressure to the pole, forming an
arch, until you are able to insert the pole tip
into the grommet
– Attach the two Frame Clips at
the mesh vent to the pole
– Repeat for second pole
1
2
Layout & Positioning
of Tent, Pole Assembly
– Layout and position tent with door facing
desired direction. (illus. 1)
– For best results in windy conditions, postion
door or back of tent into the wind.
– Unzip door.
– Stake down tent corners. Keep the floor
taut.(illus. 2)
– Assemble Frame Poles by interlocking the
shock-corded sections. This will make two
long poles.
– Lay the poles out diagonally, centered on the
tent.The center of the poles should cross
forming an “X” in the middle of tent. (illus. 1)
– Fasten Toggle & Loop on top of tent over both
poles. (illus. 1), (illus. 3)
illus. 1
Toggle & Loop
illus. 2
Tent stake
through Loop
illus.4
Insert Pole Tip on
stake loop into pole. illus. 5 Tent frame set-up
illus. 3
Toggle &
Loop
POLE ASSEMBLY PARTS
illus. 6
Frame Clips
aries
™
2
part number 9805-230
Main Tent Poles (2)
Part No. 9805-1101
Rainfly
Part No. 9805-1151

Pro-Tips
• Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your
tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is
NOT LEAKAGE through the tent fabric. Propping open the exterior vents on the rainfly, allowing good ventilation
through the tent, can minimize condensation.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO
REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
3Attach Tent to Frame
Using Frame Clips
– Attach remaining frame clips
along the edges of tent to frame
poles (illus. 7), (illus. 8)
– Make any adjustments to the tent
corner stakes that are needed.
4Attach Rainfly
– Drape Rainfly over tent frame. Zipper
should be out over front door and logos
on each side.
– Secure Rainfly with velcro ties located
on underside of fly to the tent poles.
There is one in the top center and 4
attached to each pole. (illus. 11)
– Connect the four clips (found at the
Rainfly corners) to the clips located at
the corners of the tent. (illus. 10)
– Secure Guy Lines by extending away
from tent and staking out when taut.
(illus.11).
illus. 8
Assembled tent without
Rainfly. Note the frame clips
located on edge of tent.
illus. 7
Frame Clips
illus. 11
Completed tent
with Rainfly. Note
where Rainfly clips,
Guy Lines, and velcro
ties are located
Velcro ties on
underside of Rainfly
attach to frame poles
Guy Line
illus. 10
Rainfly clips
onto pole
stake loop
illus. 9
Rainfly clips
onto pole
stake loop
Velcro ties
Rainfly Clips
PRINTED IN CHINA
© 2002 The Coleman Company, Inc. All Rights Reserved.