Coleman 90445E User manual

90445E
FILTER PUMP
OWNER’S MANUAL
DO NOT RETURN THIS ITEM TO THE STORE OR
WEBSITE WHERE IT WAS PURCHASED.
PLEASE VISIT BESTWAYCORP.COM/SUPPORT
FOR QUESTIONS, OR FOR DEFECTIVE OR
WARRANTY CLAIMS.
Para la instrucción en español,
visite bestwaycorp.com/support

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
FCC ID: 2ACGN-BW58614
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power.
Push the reset button.Power should be restored. If the GFCI fails to operate in
this manner, the GFCI is defective. If the GFCI interrupts power to the pump
without the test button being pushed, a ground current is flowing, indicating the
possibility of an electric shock. Do not use this pump. Disconnect the pump and
have the problem corrected by a qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged
cord immediately. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
WARNING - To reduce the risk of electric shock, do not use
extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION - For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical
supply is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position of
pool and pump so adequate ventilation, drainage, and access for cleaning is available.
Never place pump in an area that may accumulate water, or in an area where foot
traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
NOTE: Do not add chemicals in the filter pump.
NOTE: Assembly and disassembly of this product should only be performed
by adults.
• THERMALLY PROTECTED MOTOR CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST
SHOCK HAZARD, USE ONLY IDENTICAL REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
•CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS
ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS.
•CAUTION: CONNECT ONLY TO GROUNDING TYPE
RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT
INTERRUPTER.
•CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
FILTER PUMP
OWNER’S MANUAL
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
2
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
FCC ID: 2ACGN-BW58614
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power.
Push the reset button.Power should be restored. If the GFCI fails to operate in
this manner, the GFCI is defective. If the GFCI interrupts power to the pump
without the test button being pushed, a ground current is flowing, indicating the
possibility of an electric shock. Do not use this pump. Disconnect the pump and
have the problem corrected by a qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged
cord immediately. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
WARNING - To reduce the risk of electric shock, do not use
extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION - For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical
supply is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position of
pool and pump so adequate ventilation, drainage, and access for cleaning is available.
Never place pump in an area that may accumulate water, or in an area where foot
traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
NOTE: Do not add chemicals in the filter pump.
NOTE: Assembly and disassembly of this product should only be performed
by adults.
• THERMALLY PROTECTED MOTOR CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST
SHOCK HAZARD, USE ONLY IDENTICAL REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
•CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS
ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS.
•CAUTION: CONNECT ONLY TO GROUNDING TYPE
RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT
INTERRUPTER.
•CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
3
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
FCC ID: 2ACGN-BW58614
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power.
Push the reset button.Power should be restored. If the GFCI fails to operate in
this manner, the GFCI is defective. If the GFCI interrupts power to the pump
without the test button being pushed, a ground current is flowing, indicating the
possibility of an electric shock. Do not use this pump. Disconnect the pump and
have the problem corrected by a qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged
cord immediately. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
WARNING - To reduce the risk of electric shock, do not use
extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION - For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical
supply is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position of
pool and pump so adequate ventilation, drainage, and access for cleaning is available.
Never place pump in an area that may accumulate water, or in an area where foot
traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
NOTE: Do not add chemicals in the filter pump.
NOTE: Assembly and disassembly of this product should only be performed
by adults.
• THERMALLY PROTECTED MOTOR CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST
SHOCK HAZARD, USE ONLY IDENTICAL REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
•CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS
ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS.
•CAUTION: CONNECT ONLY TO GROUNDING TYPE
RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT
INTERRUPTER.
•CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
4
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
FCC ID: 2ACGN-BW58614
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power.
Push the reset button.Power should be restored. If the GFCI fails to operate in
this manner, the GFCI is defective. If the GFCI interrupts power to the pump
without the test button being pushed, a ground current is flowing, indicating the
possibility of an electric shock. Do not use this pump. Disconnect the pump and
have the problem corrected by a qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged
cord immediately. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
WARNING - To reduce the risk of electric shock, do not use
extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION - For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical
supply is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position of
pool and pump so adequate ventilation, drainage, and access for cleaning is available.
Never place pump in an area that may accumulate water, or in an area where foot
traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
NOTE: Do not add chemicals in the filter pump.
NOTE: Assembly and disassembly of this product should only be performed
by adults.
• THERMALLY PROTECTED MOTOR CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST
SHOCK HAZARD, USE ONLY IDENTICAL REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
•CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS
ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS.
•CAUTION: CONNECT ONLY TO GROUNDING TYPE
RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT
INTERRUPTER.
•CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
5
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
P05554
P04949
P61733ASS16
90358
P06032
P6019ASS16
P6517ASS16
P6124ASS16
P6005ASS16
P6029ASS16
P6916ASS16
P61408ASS16
P6680ASS16
P61318ASS16
A
1
1
1
1
1
2
2
5
2
3
2
1
2
1
B
1
1
1
1
1
2
2
4
2
3
0
1
2
0
P6124ASS16
P6916ASS16
P6680ASS16
P61318ASS16
P61408ASS16
P6005ASS16
P6029ASS16
P6019ASS16
P6517ASS16
AB
B
A
B
X3
X1 X2
P04949
P05554
P61733ASS18
90358
P06032
P6029ASS16
P6029ASS16

1 2
3 4
A
B
B
P6517ASS16
P6019ASS16
P6019ASS16
P61408ASS16
A
A
B
B
B
A
B
A
B
P6680ASS16
A
B
B
B
P6124ASS16
A
B
B
A
B
B
P61318ASS16 P6680ASS16
P6916ASS16
AB
1) Open/unscrew the air purge valves on the filter pump; air will be released as water fills the filter pump.
2) When water comes out of the air purge valves, close the air purge valves and wipe away any remaining water.
3) Test the GFCI plug.
4) Start the filter pump by pressing the switch button.
Operation
6

A. To test the GFCI, plug it into a grounding type receptacle.
B. Press the “RESET” button; the indicator should turn red.
NOTE: If the indicator light is not on, the test has failed.
C. Press the “TEST” button. The indicator should turn off.
NOTE: If the indicator light is not off, the test has failed.
D. Press the “RESET” button. If the indicator light turns red, the filter pump is ready for use.
WARNING: RISK OF ELECTRIC SHOCK: THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING: DO NOT USE THE PUMP IF THE ABOVE TEST FAILS.
Please contact your local Bestway Customer Service.
NOTE: Never operate the pump while the connection valves are closed.
NOTE: To prevent the risk of electrical shock, ensure your hands are completely dry when plugging-in the filter
pump.
IMPORTANT: DO NOT DRY RUN THE FILTER PUMP - Make sure both the pool’s Inlet and Outlet valves
are fully covered by water before operating the filter pump.
GFCI Test
RESET
TEST
RESET
TEST
RESET
TEST
A B CD
Important：
1. After setting the run time, the pump will restart automatically at the same time
the following day.
2. In case of power outage or power cord loosening, the running time of the
product will be reset to a 10 hour default.
7
On/Off button/Wi-Fi toggle
This button has two functions:
- On/off function: To start or stop the pump.
- Wi-Fi activation function: For more information, please refer to Wi-Fi
operation instructions.
Time setting button
During the set-up operation, the display will flash. Every time you push the
set-up button, the timer will decrease 1 hour. When you reach the desired
time, don’t push any buttons for 5 seconds. The display light will stop flashing.
The set-up is finished.
Wi-Fi indicate light
This LED indicates the status of the Wi-Fi connection. Check the Wi-Fi
Indicator Light Definitions section for the different statuses of this LED.

8
Caution: Wi-Fi indicator only indicates the state of connection between the pump
and the wireless router. When your Wi-Fi indicator lights up but the device in the
app is offline, please check whether your wireless router network is malfunctioning.
Filter cartridge status indicator / Low flow rate
Filter indicator on: The filter element is dirty, or the system has detected a low
flow rate.
Follow the trouble shooting instructions to reset the element.
Digital display
“ - - ” indicates ‘Standby Status’ - Press the On/Off button to access the
pump’s set run timer.
Wi-Fi Indicator Light Definitions
Indicator Display
WiFi indicator lights on Connected to the router
Light damaged / Wi-Fi module has problem
Lost Wi-Fi signal
Waiting to connect to the router
Definition
WiFi indicator lights off
WiFi indicator flashes quickly
WiFi indicator flashes slowly
Trouble shooting
Important: If the detection shows “Er” or the app prompts ''Filter pump detects no
water flow", turn off the power switch and resolve the problem according to the
following solutions.
Code Reasons Solutions
• Make sure that the inlet and outlet of the pool
are fully covered by water.
• Make sure the inlet and outlet valves are
open.
• Purge air from the whole circulation system.
• For assistance, please visit the support
website www.bestwaycorp.com.
• Check and open the control valve.
• Remove the blockage and reset the alarm.
• Take out the filter cartridge and rinse it.
Replace the filter element with a new one, in
case the alarm remains.
• For assistance, please visit the support
website www.bestwaycorp.com.
Device displays "Er"
or app prompts "Filter
pump detects no water
flow"
• The system detects no
water flow.
• The pump is on but the
motor isn't running.
• Control valve is closed or
not completely open.
• Debris is blocking hoses /
debris screen.
• The filter cartridge is dirty.
The filter indicator lights
up or app prompts
"Filter cartridge is dirty
/ Low flow rate"
• Click ''x'' to close.
• For assistance, please visit the support
website
www.bestwaycorp.com.
• This alarm will appear if
the timing interface is
open and the filter pump
is switched off at the
same time.
The app prompts "The
filter pump is off and
cannot be controlled"

Problems
The Wi-Fi setup is not
successful
Probable Causes Solutions
The pump has been
connected to the wrong band
The spa pump location is too
far from the router
Set up the wrong Network
Name
The Wi-Fi password used
during the connection is wrong
The strength of the Wi-Fi
signal is not stable
There is an appliance near
the spa pump or the router
that creates Signal Interference
Your phone will not connect
to the Wi-Fi network during
the registration
APP Feedback
9
If the router your pump is connected to is
dual-band and currently not connecting to a
2.4GHz network, please switch to another
band of the same router (2.4GHz) and try to
pair pump heater again. 5GHz networks are
not supported.
Check with your cell phone to see if there is
full Wi-Fi signal. In case the strength of the
signal on your phone is too low, check
where the strength of the Wi-Fi signal
is full and place the spa in that position.
Start the connection procedures again and
be sure that the network name is typed
correctly.
Start the connection procedures again and
be sure that the password is correct.
The Wi-Fi connectivity can be interrupted by
electromagnetic
or other interferences. Keep the
appliance away from other
electronic devices
that may cause interferences.
Check if the mobile device is in airplane
mode.
Make sure to have the airplane mode
deactivated when connecting to the Wi-Fi
network.
Consult the help section in the APP for
extensive and up-to-date troubleshooting
tips.
1. Check if the router works correctly.
2. Go near the spa and check the signal on
your phone.
In case the signal strength is not
stable, check the condition
of your router. In
case the signal strength is full, repeat the
operation to connect the spa to the
network.

Bestway Smart HubTM Connection Guide
STEP 1: Ensure your mobile device is connected to Wi-Fi.
STEP 2: Plug in the pump. Press the On/Off Button for 5 seconds to begin syncing. The Wi-Fi
indicator light should be flashing a green light slowly.
NOTE: Ensure the pump is plugged in and test the GFCI.
STEP 3: Open the Bestway App on your mobile device. Follow the step-by-step guide to syncing with your app.
○ Login or register your account.
○ Press 'Add Devices', Select 'POOL CONTROL'.
○ Once the Wi-Fi network has been found, input your Wi-Fi password.
○ Change to the Wi-Fi service to: BW-Flowclear-xxx Password: 123456789
(Andriod system will slip this step and start connectin process directly)
○ Go back to the app, and wait until the connecting process is finished.
Now you can control your pump by both mobile device and control panel.
10
Download the Bestway App from the Apple Store/Google Play Store.
The device can only be connected to one mobile phone at a time. If you want to
connect to another mobile phone, or your network has been changed, you can do
as follows:
Press the On/Off Button for 5 seconds. When the indicator flashes slowly, the
device will clear the connection information of the previous mobile phone.
Please follow the instructions to connect the new mobile phone to the pump.
Note: Before connecting the App to the pump, please make sure that your mobile
device is close to the pump and the Wi-Fi signal is strong.
Note: This App supports Android 7.0 and above or iOS 10.0 and above.
Note: The device only supports distributing 2.4G network, but does not support 5G
network.
Note: It is not recommended to use public Wi-Fi. When connected to the public
Wi-Fi, you may have issues with the input verification codes during Log-in.
Note: Open Location services in mobile settings before connecting your
phone to the filter pump.
Note: Language setting can be changed in app.

Sharing function
Note: Only one person can scan the Shared QR code generated each time. If you want to share it with
another device, you must generate a new Shared QR code each time. The Shared QR code expires after
15 minutes. The sharing function can only be used when users are in the same country.
Disconnect
Press the button for 5 seconds until the indicator is flashing.
11
PUMP MAINTENANCE
CAUTION: YOU MUST ENSURE THE FILTER PUMP IS UNPLUGGED
BEFORE ANY MAINTENANCE BEGINS OR FACE SEVERE RISK OF INJURY
OR DEATH.
1) Unplug the Filter Pump.
2) Stop water flowing to the Filter Pump. (Refer to pool’s manual.)
3) Unscrew the Filter Cap Retainer and remove the Filter Cap.
4) Clean the Filter Cartridge with a garden hose.If filter cartridge remains soiled or
discolored, it is necessary to replace it with a new one.
5) Insert the cleaned (or new) Filter Cartridge; ensure it is centered in the Filter
Pump.
6) Check that the Filter Cap Seal is in place.
7) Replace the Filter Cap and screw the Filter Cap Retainer into position.
8) Open the Valve A and B.
9) Follow the PUMP INSTALLATION DIRECTIONS section to prepare the system
for use.
IMPORTANT: To ensure pool water stays clean, please clean the
filter cartridge every day. For sanitary reasons, wesuggest replacing the Filter
Cartridge with a new one every two weeks.
PUMP STORAGE
1) Unplug the Filter Pump.
2) Stop water flowing into the Filter Pump and to remove the Filter Cartridge.
3) Discard the Filter Cartridge.
4) Detach all Hoses.
5) Dry all components thoroughly.
6)
Store the filter pump in a dry location out of the reach of children. Storage
temperature: 4-40°C（39.2-104°F）
7) Drain the pool according to the Pool Owner’s Manual.
PUMP WARRANTY
For information concerning pump warranty please visit our website at:
www.bestwaycorp.com

©2020 The Coleman Company, Inc.
is a registered trademark of The Coleman Company, Inc., used under license.
Manufactured by
©2020 Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
®™ Trademarks used in some countries under license to
Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China
Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
www.bestwaycorp.com
303021247709