Coleman FlowClear 90402E User manual

90402E
FILTER PUMP
OWNER’S MANUAL
DO NOT RETURN THIS ITEM TO THE STORE OR
WEBSITE WHERE IT WAS PURCHASED.
PLEASE VISIT BESTWAYCORP.COM/SUPPORT
FOR QUESTIONS, OR FOR DEFECTIVE OR
WARRANTY CLAIMS.
Para la instrucción en español,
visite bestwaycorp.com/support

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault
circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button.Power should be restored. If the GFCI fails
to operate in this manner, the GFCI is defective. If the GFCI interrupts power to
the pump without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this pump. Disconnect
the pump and have the problem corrected by a qualified service representative
before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, IF FILTER PUMP
POWER CORD BECOMES DAMAGED IN ANY WAY, THE PUMP MUST BE
DISCARDED.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION -For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical supply
is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position
of pool and pump so adequate ventilation, drainage, and access for cleaning is
available. Never place pump in an area that may accumulate water, or in an area
where foot traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
FILTER PUMP
OWNER’S MANUAL
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
2

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault
circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button.Power should be restored. If the GFCI fails
to operate in this manner, the GFCI is defective. If the GFCI interrupts power to
the pump without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this pump. Disconnect
the pump and have the problem corrected by a qualified service representative
before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, IF FILTER PUMP
POWER CORD BECOMES DAMAGED IN ANY WAY, THE PUMP MUST BE
DISCARDED.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION -For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical supply
is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position
of pool and pump so adequate ventilation, drainage, and access for cleaning is
available. Never place pump in an area that may accumulate water, or in an area
where foot traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
3

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault
circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button.Power should be restored. If the GFCI fails
to operate in this manner, the GFCI is defective. If the GFCI interrupts power to
the pump without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this pump. Disconnect
the pump and have the problem corrected by a qualified service representative
before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, IF FILTER PUMP
POWER CORD BECOMES DAMAGED IN ANY WAY, THE PUMP MUST BE
DISCARDED.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION -For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical supply
is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position
of pool and pump so adequate ventilation, drainage, and access for cleaning is
available. Never place pump in an area that may accumulate water, or in an area
where foot traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
NOTE: Do not add chemicals in the filter pump.
NOTE: Assembly and disassembly of this product should only be
performed by adults.
• THERMALLY PROTECTED MOTOR CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST
SHOCK HAZARD, USE ONLY IDENTICAL REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
• CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS
ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS.
• CAUTION: CONNECT ONLY TO GROUNDING TYPE
RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT
INTERRUPTER.
• CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
• WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin.
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands.
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
4

WARNING
IMPORTANT SAFETY
INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING - RISK OF ELECTRIC SHOCK - The pump cannot be
using while people are inside the pool.
WARNING - TO REDUCE THE RISK OF INJURY, do not permit
children to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK. Connect only to a
grounding type receptacle.This product is provided with a ground-fault
circuit-interrupter. If replacement of the plug is needed, use only identical
replacement parts.
WARNING: The unit is provided with a ground-fault
circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button.Power should be restored. If the GFCI fails
to operate in this manner, the GFCI is defective. If the GFCI interrupts power to
the pump without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this pump. Disconnect
the pump and have the problem corrected by a qualified service representative
before using.
CAUTION - To reduce the risk of electric shock the pool must be
installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place
portable appliances closer than 5 feet (1.5 m) from the pool.
WARNING: The pump is not intended to be bonded to the
equipotential bonding grid.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, IF FILTER PUMP
POWER CORD BECOMES DAMAGED IN ANY WAY, THE PUMP MUST BE
DISCARDED.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION - This pump is for use with storable pools only. Do not use
with permanently-installed pools. A storable pool is constructed so that it is
capable of being readily disassembled for storage and reassembled to its original
integrity. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage.
CAUTION -For continued protection against possible electric shock
this unit is to bemounted to the base in accordance with the installation
instructions.
IMPORTANT - Using the pump with an unmatched electrical supply
is dangerous and will result in catastrophic failure of pump.
RISK OF ELECTRIC SHOCK - When working with electricity, turn the electrical
power off at the circuit breaker and lock breaker door. Failure to do so will result in
increased risk of shock, injury and possibly death.
DO NOT REMOVE THE GROUNDING PRONG OR MODIFY THE PLUG IN ANY
WAY. DO NOT USE ADAPTOR PLUGS. Consult a qualified electrician for any
questions related to the validity of your plugs grounding. Handle the pump with
care. Do not pull or carry the pump by the power cord. Never pull a plug from the
outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects,
oil, moving parts, and heat should never be exposed to the filter pump.
NOTE: Please examine equipment before use. Notify Bestway at the
customer service address listed on this manual for any manufacturing defect or
missing parts at the time of purchase. Verify that the equipment components
represent the filter pump model that you had intended to purchase.
NOTE: Place pump on a solid and level ground. Pay attention to position
of pool and pump so adequate ventilation, drainage, and access for cleaning is
available. Never place pump in an area that may accumulate water, or in an area
where foot traffic will flow around the pool.
NOTE: Atmospheric conditions may affect the performance and life span
of your filter pump. Unnecessary wear and tear may occur during periods of cold,
heat and exposure to sun. Whenever possible shelter the pump from these
conditions.
5
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
P6019ASS16
P6124ASS16
P6362ASS16
P6132ASS16
P6680ASS16
P61318ASS16
P06034
P6005ASS16
P6(H1)115ASS16
P05425
P6119ASS16
A
B
90357
A B C
P05425
P6(H1)115ASS16
P6119ASS16
90357
P06034
P6019ASS16
P6132ASS16
P6124ASS16
P6005ASS16
P6362ASS16
P6680ASS16
P61318ASS16
1
1
1
1
1
2
2
8
5
1
2
1
1
1
1
1
1
2
2
5
5
1
0
0
1
1
1
1
1
2
0
2
2
0
0
0
A
B
C
X3
X3
X2 X1 X1

1 2
3 4
B
B
A
P6362ASS16
P6019ASS16
P6132ASS16
P6132ASS16
A
B
ABB
A
B
A
B
X2
BB
A
P61318ASS16 P6680ASS16
P6124ASS16
3 4
1 2
B
A
P6019ASS16 P6019ASS16
B
A
A
B
A
B
A
B
B
A
P61318ASS16 P6680ASS16
B
A
P6124ASS16
6

NOTE: It is important to ensure all elements: Hoses, Debris Screens and Inlet/Outlet Valves are properly aligned.
Operation
1) Open/unscrew the Air Purge Valve on the top of the Filter Pump; air is released as water fills the Filter Pump.
Note: If knob should become dislodged, simply place it back into the hole and turn clockwise to rethread air purge valve.
2) When water comes out of the Air Purge Valve screw it closed and wipe away any water.
3) Test the GFCI plug.
NOTE: It is imperative to check that the hydraulic connectors are not closed.
PEDESTAL FIXING
The filter pump must be vertically fixed on ground or a certain pedestal made of wood or concrete before use. There
should be two holes 9mm in diameter on the pedestal, the space between which should be 166mm. Put filter pump on the
pedestal and fix them together by fasten the bolts and nuts. All the pedestal parts should weigh over 18kgs at least to
prevent the pump from accidentally falling.
390
166
390
250
166
2-M8 bolt
2-M8 nut
B
A
A
B
B
A
A
B
A. To test the GFCI plug, insert it into a grounding type receptacle.
B. Press the “RESET” button; the indicator turns red.
GFCI Test
RESET
TEST
RESET
TEST
RESET
TEST
A B CD
7
NOTE: If the indicator light is not on, the test has failed.
C. Press the “TEST” button. The indicator turns off.
NOTE: If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the filter pump is ready for use.
WARNING: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING: DO NOT USE THE PUMP IF THE ABOVE TEST FAILS.
Please contact your local Bestway Customer Service.
NOTE: To prevent the risk of electrical shock, ensure your hands are completely dry when plugging-in the Filter
Pump.
IMPORTANT: DO NOT DRY RUN THE FILTER PUMP - Make sure both the pool’s Inlet and Outlet valves
are fully covered by water before operating the Filter Pump.
Maintenance
CAUTION: YOU MUST ENSURE THE FILTER PUMP IS UNPLUGGED BEFORE ANY MAINTENANCE OR
STORAGE BEGIN S OR SEVERE RISK OF INJURY OR DEATH EXISTS.
1) Unplug the Filter Pump.
2) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses by unscrewing the fly nut counter-clockwise.
3) Remove Debris Screens from the inside of the pool.
4) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet and Outlet Valves.
5) Unscrew the Filter Cap Retainer and remove the Filter Cap.
6)
Clean the Filter Cartridge with a garden hose, if filter cartridge remains soiled or discolored, it is necessary to replace it with a
new one.
7) Insert the cleaned (or new) Filter Cartridge; ensure it is centered in the Filter Pump.
8) Check that the Filter Cap Seal is in place.
9) Replace the Filter Cap and screw the Filter Cap Retainer into position.
10) Replace the Stopper Plugs with the Debris Screens in the pool’s Inlet and Outlet Valves. Tighten the Hose Clamps.
Water will now flow to the pump.
11) Follow the PUMP INSTALLATION DIRECTIONS section to prepare the system for use.
IMPORTANT: For sanitary reasons we suggest replacing the Filter Cartridge with a new one every two
weeks.
STORAGE
1) Unplug the Filter Pump.
2) Follow the instructions as previously outlined to stop water flowing to the Filter Pump and to remove the Filter Cartridge.
3) Discard the Filter Cartridge.
4) Detach all Hoses.
5) Dry all components thoroughly.
6) Store the filter pump in a dry location out of the reach of children. Storage temperature: 4-40OC (39.2-104OF)
Pump Warranty
For information concerning pump warranty please visit our website at: www.bestwaycorp.com

A. To test the GFCI plug, insert it into a grounding type receptacle.
B. Press the “RESET” button; the indicator turns red.
8
NOTE: If the indicator light is not on, the test has failed.
C. Press the “TEST” button. The indicator turns off.
NOTE: If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the filter pump is ready for use.
WARNING: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING: DO NOT USE THE PUMP IF THE ABOVE TEST FAILS.
Please contact your local Bestway Customer Service.
NOTE: To prevent the risk of electrical shock, ensure your hands are completely dry when plugging-in the Filter
Pump.
IMPORTANT: DO NOT DRY RUN THE FILTER PUMP - Make sure both the pool’s Inlet and Outlet valves
are fully covered by water before operating the Filter Pump.
Maintenance
CAUTION: YOU MUST ENSURE THE FILTER PUMP IS UNPLUGGED BEFORE ANY MAINTENANCE OR
STORAGE BEGIN S OR SEVERE RISK OF INJURY OR DEATH EXISTS.
1) Unplug the Filter Pump.
2) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses by unscrewing the fly nut counter-clockwise.
3) Remove Debris Screens from the inside of the pool.
4) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet and Outlet Valves.
5) Unscrew the Filter Cap Retainer and remove the Filter Cap.
6)
Clean the Filter Cartridge with a garden hose, if filter cartridge remains soiled or discolored, it is necessary to replace it with a
new one.
7) Insert the cleaned (or new) Filter Cartridge; ensure it is centered in the Filter Pump.
8) Check that the Filter Cap Seal is in place.
9) Replace the Filter Cap and screw the Filter Cap Retainer into position.
10) Replace the Stopper Plugs with the Debris Screens in the pool’s Inlet and Outlet Valves. Tighten the Hose Clamps.
Water will now flow to the pump.
11) Follow the PUMP INSTALLATION DIRECTIONS section to prepare the system for use.
IMPORTANT: For sanitary reasons we suggest replacing the Filter Cartridge with a new one every two
weeks.
STORAGE
1) Unplug the Filter Pump.
2) Follow the instructions as previously outlined to stop water flowing to the Filter Pump and to remove the Filter Cartridge.
3) Discard the Filter Cartridge.
4) Detach all Hoses.
5) Dry all components thoroughly.
6) Store the filter pump in a dry location out of the reach of children. Storage temperature: 4-40OC (39.2-104OF)
Pump Warranty
For information concerning pump warranty please visit our website at: www.bestwaycorp.com

©2020 The Coleman Company, Inc.
is a registered trademark of The Coleman Company, Inc., used under license.
Manufactured by
©2020 Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
®™ Trademarks used in some countries under license to
Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China
Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
www.bestwaycorp.com
303021247701