Color Sage CS-B144B User manual

CS-B144B BATTERY PAR CAN
User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS
Factory: No.186, South Tingshi Road, Shijing Town, Baiyun District, Guangzhou,China.
[phone]
[email protected]
www.color-sage.com YOUTUBE FACEBOOK
RGBWA+UV

*CAUTION!
Becareful with your operations.With a dangerous voltage you cansuffer a
dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
*IMPORTANT!
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.
If the device has been exposed to temperature changes due to environmental changes, do not switch
it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for
smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
1. SAFETY INSTRUCTIONS
01 02
Thank you for choosing our CS-B144B LED BATTERY PAR CAN.
For your own safety, please read this manual before installing the device. This manual covers the
important information on installation and applications. Please install and operate the fixture with
following instructions.
This LED BATTERY PAR CAN use 12PCS*12W LEDs. Charging about 5-6 hours can use about 4.5
hours of full color, or about 20 hours of single color.
This product is used to enliven atmosphere for family gatherings, KTV box, disco ballroom, ballroom,
nightclub, disco, bar, mall, wedding, square, park, etc.
Function:
1. Master/Slave,
2. Sound actived,
3. Automatic
4. DMX 512
5. Wireless DMX (Optional)
6. IR remote control (Optional)
2. UNPACKING
3. FEATURES & SPECIFICATIONS
CS-B144B LED BATTERY PAR CAN
IRC REMOTE
IRC Remote (Optional) User Manual
User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS
UK Standard
(Optional)
USAStandard
(Optional)
Euro Standard
(Optional)
Power cable

03 04
7. LED dimmer,
8. Color jumping,
9. Color Gradual change
10. Color Pulse change
11. Strobe
Specifications:
LED quantities: 12pcs*12W LEDs
Input Voltage: AC90V-240V, 50/60HZ
Power consumption: 72W
Channel: 6/10 CH
Beam Angle: 40° (25° Optional)
Display Screen: LCD display
Battery Type: Lithium battery
Battery Charging Time: About 5-6 hours
Battery Using Hours: About 4.5 hours of full
color, about 20 hours of single color.
Color: RGBWA+UV 6 in 1
Material Science: Iron alloy
Packing & weight:
Size: 250mm*200mm*320mm
Net Weight: 4.7kg
Packing:250mm*250mm*360mm
Gross Weight: 5.2kg
01. Don’t turn on the fixture if it’s been through severe temperature difference like after transportation
because it might damage the light due to the environment changes. So make sure to operate the
fixture until it is in normal temperature.
02. This light should be keep away from strong shaking during any transportation or movement.
03. Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
04. Don’t expose the fixture in overheat, moisture or environment with too much dust when installing
it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
4. OPERATION INSTRUCTIONS
05. Make sure the installation place is in good safety condition before installing the fixture.
06. Make sure to put the safety chain and check whether the screws are screwed properly when
installing the fixture.
07. Make sure the lens are in good condition. It’s recommended to replace the units if there are any
damages or severe scratch.
08. Make sure the fixture is operated by qualified personnel who knows the fixture before using.
09. Keep the original packages if any second shipment is needed.
10. Don’t try to change the fixtures without any instruction by the manufacturer or the appointed
repairing agencies.
11. It is not in warranty range if there are any malfunctions from not following the user manual to
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
5. MENU OPERATIONS
MENU: Access the menu.
DOWN: Reduction key or key under the selected; decrease the value function
down menu.
UP: Add key or selection on the key; increase the value function, shift on the menu.
ENTER: It is used to select and confirm/store the current selection.
MENU DOWN UP ENTER
200mm
200mm
200mm

05 06
CL01
Red dimming/0-255 0-255 from dark to bright
r255
Green dimming/0-255 0-255 from dark to bright
G255
Blue dimming/0-255 0-255 from dark to bright
b255
White dimming/0-255 0-255 from dark to bright
u255
Amber dimming/0-255 0-255 from dark to bright
Y255
UV dimming/0-255 0-255 from dark to bright
P255
IR remote control/0-255 IR remote control brightness
I255
Strobe speed/0-255 0-255 from slow to fast
FF00
Static color selectable/
0-255
Color jumping/0-15 0-15, Speed from slow to fast
CC12
15 kinds static color selectable
Color gradual change/0-15
0-15, Speed from slow to fastDE15
Color Pulse change/
0-15 0-15, Speed from slow to fastCP13
Sound control/0-15 Voice sensitivity, 0-15 from low
to high
SU13
Current temperature
display/0-99
when not used the dislpay will
show : t ---
t 30
Version numberVEr1
Reset
rSEt
6. DMX CHANNELS
InstructionsFunction/ValueChannel
1 Red dimming/1-255 0-255 from dark to bright
2 Green dimming/1-255
0-255 from dark to bright
3 Blue dimming/1-255
0-255 from dark to bright
4 White dimming/1-255
0-255 from dark to bright
5 Amber dimming/1-255
0-255 from dark to bright
6 UV dimming/1-255
0-255 from dark to bright
6 Channel
InstructionsFunction/Value
Channel
1 Red dimming 0-255 from dark to bright
2 Green dimming 0-255 from dark to bright
3 Blue dimming 0-255 from dark to bright
4 White dimming 0-255 from dark to bright
5 Amber dimming 0-255 from dark to bright
6 UV dimming 0-255 from dark to bright
7 Master dimmer
RGBWAUV master dimmer, 0-255 from slow to fast
8 Master strobe
RGBWAUV master strobe, 0-255 from slow to fast
9 Function selection
0-50 no function,
51-100 15 kinds of color output, controlled by CH10,
101-150 Color jumping,
151-200 Color Gradual change,
201-250 Color Pulse change,
251-255 Sound control.
10 Function speed
Function speed, 0-255 from slow to fast
(When color output, it is color selection)
10 Channel
InstructionsFunction/ValueMENU
001-512,
6 Channel mode.
d001 DMX512 address setting
10 Channel mode,
001-512
A001 DMX512 address setting
SL/FA, DMX512
dimming speed setting
S-SL SL: slow dimming;
FA: fast dimming
Ho/of, DMX signal loss
processing mode setting
d-Ho
Ho: keep the last DMX signal state;
oF: Turn off all LEDs
ON-OF rFon Wireless dmx control
ON-OF Iron IR remote control

BLACK OUT Mode
It is a remote switch , Press “BLACK OUT” one time,
it will open the IR remote model, and it will default to
color jump mode “CC12” , also will enter to the
previously saved mode if some mode has been
saved, press “BLACK OUT” one time again, it will
Exit the remote control function and save the current
settings.
AUTO Mode
Automatic mode will enable you to run the automatic
programs on the product.
To turn on Automatic mode:
1. Press “AUTO” on the remote controller.
2. Press “+” or “-” to choose between the different auto
programs.
SOUND Mode
Sound-Active mode will enable the product to respond
to the music.
To turn on Sound-Active mode:
1. Press “SOUND” on the remote controller.
2. Press “+” or “ - ” to choose between the different
sound programs.
FADE Mode
It is a color gradient mode.
1. Press “FADE” on the remote controller.
2. Press “FADE” again to turn off the Fade mode.
3. Press “+” or “- ” to either increase or decrease the
speed of the program.
MANUAL Mode
1. Press “MANUAL” one time ,, the menu display show “dIon”, turn on the remote controller.
2. Press “R”, “G”, “B”, “W”, “A” or “UV” (red, green, blue, white, amber, UV) to choose your
Wanted colour.press the 1st time, it is 20% brigtness, press the 2nd time, it is 40% birghtness
press the 5th time, it is 100% bightness.
Press the 6th time, turn off the manual color which you chosen.
7. Remote Controller Useing (Optional)
07
IRC REMOTE
% Mode
Adjust the birghtness of RGBWAUV color, press the 1st time, it is 10% brigtness, press the 2nd
time, it is 20% birghtness ......, press the 10th time, it is 100% bightness.
NUMBER 0~9
0-9 kinds Static color mode, press one time for your wanted color, Press “+” or “ - ” to either
increase or decrease brightness.
STROBE Mode
It should be worked with Auto mode /sound mode/fade mode/manual mode/0-9 static color model
together press the “STROBE” one time , it is 1/8 speed , press the 2nd time, it is 2/8 speed , press
the 8th time, it is 100% speed.
SENSITIVITY Mode
It is reset function, press it one time, enter the initial function press it once again, restore factory
settings, exit the remote control and enter A01.
SPEED Mode
This product does not support this feature for now.
08

The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected and must
not be corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots
(ceiling, suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4. The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled
installer and any safety problems have to be removed
*CAUTION!
Disconnect from mains before starting maintenance operation.
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning
to the lights.
1. Clean the inside and outside lens each week to avoid the weakneness of the lights
due to accumulation of dust.
2. Clean the fan each week.
3. A detailed electric check by approved electrical engineer each three month, make sure that the
circuit contacts are in good condition, prevent the poor contact of circuit from overheating.
4. Frequent cleaning. Please use a moist, lint- free cloth. Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under “Installation
instructions”.
Should you need any spare parts, please order genuine parts from your local dealer
8. MAINTENANCE AND CLEANING
09