Columbia Products SANI-LAV 607D User manual

1
HANDS-FREE WALL MOUNTED SINKS
Operating Manual for Hands-Free Wall Mounted Sinks
Models 607D and 607D-0.5
Columbia does not recommend use with harsh chemicals.
NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

2
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
HANDS-FREE WALL MOUNTED SINKS
Parts List
(1) Wall mount sink
(1) Double knee pedal valve with 2 nuts
(1) Swivel gooseneck spout with aerator
(1) Connecting tube for valve to spout connection
(2) Fittings, brass, 0.375” male compression and 0.375” male NPT
(1) Wall-mounting bracket
(2) Support brackets
(1) Strainer assembly with basket
Tools Required
Tape Measure
Adjustable Wrench
Drill Motor and Drill Bits
Pipe Wrench
Level
Safety Glasses
Screw Drivers: 1 Phillips & 1 Standard
Pencil
Socket Wrench
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.
4. Position the sink onto wall bracket.
5. Mark holes for fastening side mounting brackets as shown in illustration B.
6. Remove sink from the wall bracket.
7. Drill holes in wall for securing sink to wall. Screws are not provided.
Step 2
1. Install strainer assembly at the drain hole.
2. Install spout assembly using mounting nut provided.
3. Attach the elbow fitting to the back of spout.
4. Attach the connecting tube to spout.
5. Secure sink to wall.
Step 3
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect mixing check valve to valve inlet.
3. Mount valve under sink using mounting nuts provided.
4. Attach the elbow fitting to the bottom of the valve.
5. Attach the connecting tube from spout to valve.
6. Connect hot and cold water supply to mixing check valve.
Step 4
1. Remove aerator from the spout and flush water system.
2. Check connections for leaks.
3. Replace aerator onto the spout.
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Illustration A
Illustration B

3
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
HANDS-FREE WALL MOUNTED SINKS
Valve Repair Instructions
Note: Valves are designed to be repaired without having to be disconnected from mount or plumbing.
1. Turn off water source. Do not remove valve from sink.
2. Remove pedal assembly using a 15/16” open end wrench or socket wrench. As shown in
illustration A.
3. Using a 1” deep socket wrench or closed end wrench remove insert assembly as shown in
illustration B.
4. Replace with new repair kit model 1061L as shown on illustration C.
5. Reinstall pedal assembly and turn water source on.
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from spout
or valve stem assembly.
Flat washer on the
stem/plunger is worn.
To determine if the leak source is from the hot or cold side shut
cold water source off. See if water still leaks from the spout. If
leak continues then repair hot side if not repair cold side
We recommend installing valve repair
kit.
Water leaks from the
front of the valve.
O-Rings on the
plunger are worn out.
Visually determine whether the cold or hot side is leaking. We recommend replacing threaded
insert, plunger assembly & spring.
See illustrations below.
Illustration A
Illustration B
Illustration C

4
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
HANDS-FREE WALL MOUNTED SINKS
1/2" NPT Inlet
A
C
B
E
D
J
H
P
K
M
I
Q
L
O
1/2" NPT Inlets
A
C
B
E
F
G
H
P
K
M
I
Q
L
N
Part No. Decription Application
A
1041 Operated, Long Foot 103/104/105/106 (S) (L)
B
1042 Operated, Short Foot 101/102 (S) (L)
C
1043 Operated, Knee 109/110/111/112 (S) (L)
D
1049 Bolt & Nut Set (Stainless) All Single Valves
E
1050 Jam Nut (Stainless) All Valves
F
1051 Bolt & Nut Set (Stainless) All Double Valves
G
1052 Bracket All Double Valves
H
1053 Threaded Insert (Low Lead) All Valves
I
1053S Threaded Insert (Stainless) All Valves
J
1054 Bracket All Single Valves
K
1055 Plunger Assembly (Low Lead) All Valves
L
1055S Plunger Assembly (Stainless) All Valves
M
1056 Spring (Stainless) All Valves
N
1057 Body only, Double Valve (Low Lead) All Double Valves
O
1058 Body only, Single Valve All Single Valves
P
1061L Replacement Kit (Low Lead) All Valves
Q
1061S Replacement Kit (Stainless) All Valves
Replacement Parts
P 1061L Replacement Kit includes
one each: 1053L, 1055L, 1056L
Q1061S Replacement Kit includes
one each: 1053S, 1055S, 1056S
Double Knee or Foot Pedal
Single Knee or Foot Pedal

5
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
HANDS-FREE WALL MOUNTED SINKS
13”
(330mm)
16”
(406.4mm)
45º
607
8”
(127mm) 8” (127mm)
4” (102 mm)
16” (406mm)
14.875” (378mm)
Spout model 2007
5.5” (140mm)
14” (356mm)
2” drain hole
Supply Line
.5 NPT
8” (127mm)
5” (203mm)
1.25” R
32mm
Hole Configuration
Front Side
Top
wall hanger
8” (127mm)
5.5” (140 mm)
15.25”
(387.35mm)
11”
(279mm)
2” (51mm)
6.75” (171mm)
4.5”
(114.3mm)
.875” (22mm)
dia. hole
Double knee
pedal valve
model 111
Supply Line Detail
2” (51mm)
1.5” (38mm)
back splash
.25” dia. hole
wall hanger
Wall Mounting Detail
Back Splash
To Spout
.5” MNPT
Inlet Cold
.5” MNPT
Inlet Hot
Double
Knee or
Foot Pedal
Valve
3/8” Male
Compression
Supply Line
from Valve
to Spout