Columbia Products Sani-Lav ES2-505L User manual

1
AC OR BATTERY POWERED
SINKS WITH ELECTRONIC SENSORS
Operating Manual for Hands-Free Wall Mounted Sinks
AC Models ES2-505L and ES2-505L-0.5
Battery Models ESB2-505L and ESB2-505L-0.5
Columbia does not recommend use with harsh chemicals.
NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

2
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
AC OR BATTERY POWERED
SINKS WITH ELECTRONIC SENSORS
Parts List
(1) Wall mount sink
(1) AC or Battery powered sensor faucet assembly
(1) Wall-mounting bracket
(2) Support brackets
(1) Mixing check valve
(1) Strainer assembly with basket
Tools Required
Tape Measure
Adjustable Wrench
Drill Motor and Drill Bits
Pipe Wrench
Level
Safety Glasses
Screw Drivers: 1 Phillips & 1 Standard
Pencil
Socket Wrench
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.
4. Position the sink onto wall bracket.
5. Mark holes for fastening side mounting brackets as shown in illustration B.
6. Remove sink from the wall bracket.
7. Drill holes in wall for securing sink to wall. Screws are not provided.
Step 2
1. Install strainer assembly.
2. Install faucets to the sink following the instructions provided with sensor unit.
3. Attach supply tube with elbow to back of faucet.
4. Install mixing check valve and compression fitting to control box of each sensor faucet.
Step 3
1. Position the sink onto wall bracket and secure to wall.
2. Connect waste line to strainer assembly.
3. Mount sensor control box at desired location on wall.
4. Connect power line from sensor to control box.
5. Attach supply tube from faucet to control box.
6. Connect hot and cold water from the source to mixing check valve.
7. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)
8. Check connections for leaks.
9. Replace aerator onto the spout.
10. We recommend sealing top of backsplash to wall as shown in illustration C.
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Illustration A
Illustration B
Illustration C

3
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2019 Columbia Products
AC OR BATTERY POWERED
SINKS WITH ELECTRONIC SENSORS
16.5”
(419mm)
21”
(533mm)
45º
505 ES2-ESB2
9.5”
(241mm) 9.5” (241mm)
4” (102 mm)
19” (483mm)
17.875” (454mm)
6.125” (156mm)
7.5” (191mm)
17” (432mm)
2” drain hole
Stainless Steel Brackets
9.5”
(241mm)
7”
(197mm)
1.25” R
32mm
Hole Configuration
Front Side
Top
wall hanger
6” (152mm)
9.5” (241mm)
5.5” (140 mm)
18”
(457mm)
14”
(356mm)
2” (51mm)
.875” (22mm)
dia. key hole
2” (51mm)
1.5” (38mm)
back splash
.25” dia. hole
wall hanger
Wall Mounting Detail