Columbia Products SANI-LAV 727F User manual

FLOOR MOUNTED SINKS 1
Columbia does not recommend use with harsh chemicals.
NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.
Operating Manual for Floor Mounted Sinks
Models 727F and 727F.5

FLOOR MOUNTED SINKS 2
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2018 Columbia Products
Tools Required
Tape Measure
Adjustable Wrench
Drill Motor and Drill Bits
Pipe Wrench
Level
Safety Glasses
Screw Drivers: 1 Phillips & 1 Standard
Pencil
Socket Wrench
Installation Instructions
Step 1
1. 1. Attach upper and lower leg support brackets to legs with hardware (provided).
2. Place wash station sink on the leg assembly. Secure legs to bowl with hardware provided.
3. Place wash station sink at the desired location.
4. Mark the floor where the mounting holes are at the base of the legs. See illustration A.
5. Drill holes as required for mounting hardware. Hardware not included.
Step 2
1. Install Faucet to the sink using faucet mounting kit provided. We recommend using pipe thread
sealant instead of Teflon tape.
2. Install strainer assembly to the drain hole.
3. Connect hot and cold water supply lines (not included) to the back of faucets.
Step 3
1. Position wash station sinks to pre-drilled holes and secure sink to the floor.
2. Connect waste line or drain pipe to the strainer assembly. Not included.
3. Connect water supply lines (Hot and Cold) to the water source. Not included.
4. Remove aerator from the spout and flush the water system.
5. Replace aerator to the spout.
6. Check for leaks and tighten connections if necessary.
Step 4
1. Seal gap between bowl and leg assembly as shown in illustration B.
2. When mounting against wall, it is recommended sealing the top of the backsplash to wall as
shown on illustration C.
Parts List
(1) Floor mount sink
(1) Leg assembly set
(4) Washers and nuts for connection sink to leg assembly set
(1) 8” on center faucet
(1) Faucet mounting kit
(1) Strainer assembly with basket
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips
from the spout
or from under
the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source
off. See if water still leaks
from the spout. If leaks
continues repair hot side
if not repair cold side.
Recommend
installing hot
or cold faucet
repair kit.
Illustration A
Illustration B
Illustration C

FLOOR MOUNTED SINKS 3
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2018 Columbia Products
Front Side
Top
Hole Configurations
Floor Mounting Detail
.5” dia.
Floor
Mounting
Holes
10.5” on
Center
1.5” Leg
Thickness
.75” From
Edge of Leg
to First Hole
Supply Line Detail
Back Splash
1/2”
Male NPT
Hot
from Wall
Cold
from Wall
.875” [22mm]
dia. hole
8in
203.2mm
6in
152.4mm
6in
152.4mm
6.25in
158.8mm
9.5in
241.3mm
7in
178.9mm
27in
685.8mm
15.25in
387.4mm
6.25in
158.8mm
6in
152.4mm
8in
203.2mm
6in
152.4mm
20in
508mm
2in
50.8mm
14in
355.6mm
1.5in
38.1mm
1.5in
38.1mm
17in
431.8mm
17.5in
444.5mm
R.5in
12.7mm
2in
50.8mm
3.937in
100mm
45deg
R.75in
19.1mm
.75in
19.1mm
3in
76.2mm
12in
304.8mm
7.5in
190.5mm
2.25in
57.2mm
R .3125in
7.9mm
2.5in
63.5mm
15.5in
393.7mm
11in
279.4mm