Comelit PROFESSIONAL Series User manual

NVR PROFESSIONAL SERIES
ART. IPNVR716A – IPNVR732A
Please read this manual thoroughly before use and keep it for future reference

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX-
POSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY
METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER
OPENNINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is in- tended
to alert the user to the presence of dangerous voltage within the products enclosurethat
maybeofsufficientmagnitudetoconstituteariskofelectricshock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying theproduct.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRICSHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTSINSIDE.
REFER SERVICINGTOQUALIFIED SERVICE PERSONNEL

FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
CAUTION
RISK OF EXPLOSION IF BATTERYIS REPLACED BYAN INCORRECT TYPE.
DISPOSE OF USED BATTERIESACCORDING TO THE INSTRUCTIONS.
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
This Class Adigital apparatus complies with Canadian ICES-003.
Cet appareil nume
`
rique de la classe A est conforme a
´
la norme NMB-003 du
Canada.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate
radiofrequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interferenceat his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
includinginterference that may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus nearwater.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produceheat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, conve-
nience receptacles, and the point where they exit from theapparatus.
11. Only use attachments/accessories specified by themanufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When
a cart is used. Use caution when moving the cart/apparatus
combination to avoid in- jury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is re-
quired when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally,
or has beendropped.
15. CAUTION − THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN
THE OPERATING IN- STRUCTIONS UNLESS YOU QRE QUALIFIED TO DOSO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power
source only.
17. ITE is to be connected only to PoE networks without routing to the outsideplant.

Table of Contents
Table of Contents ............................................................................................................................................ 1
1. Overview 3
1.1 Package Contents................................................................................................................................ 4
1.2 Part Description.................................................................................................................................... 4
2. Installation 6
2.1 Installing HDD....................................................................................................................................... 7
2.2 Connecting with Exterior Device........................................................................................................... 7
2.3 Starting System .................................................................................................................................... 9
2.4 Setting Earlier Stage............................................................................................................................. 9
2.4.1 Account................................................................................................................................ 10
2.4.2 System..................................................................................................................................11
2.4.3 Network................................................................................................................................ 12
Time/Date 13
3. Live Screen Configuration 14
3.1 Icons in Live screen............................................................................................................................ 15
3.2 Live Launcher menu........................................................................................................................... 16
3.2.1 Backup................................................................................................................................. 17
3.3 Quick menu ........................................................................................................................................ 18
3.3.1 PTZ Control.......................................................................................................................... 18
3.3.2 Camera Registration ............................................................................................................ 20
3.3.3 Status > System log ............................................................................................................. 21
3.3.4 Status > Event...................................................................................................................... 22
3.3.5 Status > Record.................................................................................................................... 22
4. Setup menu 24
4.1 General buttons in Setup menu.......................................................................................................... 26
4.2 SYSTEM............................................................................................................................................. 27
4.2.1 System................................................................................................................................. 27
4.2.2 Time/Date............................................................................................................................. 29
4.2.3 Account > User..................................................................................................................... 32
4.2.4 Configuration (Config).......................................................................................................... 33
4.3 CAMERA............................................................................................................................................ 36
4.3.1 Basic .................................................................................................................................... 36
4.3.2 Advanced............................................................................................................................. 39

4.4 DEVICE.............................................................................................................................................. 40
4.4.1 Display ................................................................................................................................. 40
4.4.2 Disk > Setup......................................................................................................................... 46
4.4.3 PTZ > PTZ............................................................................................................................ 47
4.4.4 Serial Device > Serial Device............................................................................................... 48
4.4.5 TEXT > TEXT....................................................................................................................... 49
4.5 RECORD............................................................................................................................................ 51
4.5.1 Schedule > Schedule........................................................................................................... 51
4.5.2 Stream.................................................................................................................................. 54
4.6 EVENT ............................................................................................................................................... 58
4.6.1 System/Disk......................................................................................................................... 58
4.6.2 Alarm In................................................................................................................................ 60
4.6.3 Motion .................................................................................................................................. 63
4.6.4 Video Loss > Setup.............................................................................................................. 65
4.6.5 Notification ........................................................................................................................... 66
4.7 NETWORK......................................................................................................................................... 68
4.7.1 Basic > WAN Port................................................................................................................. 68
4.7.2 DVRNS/DDNS ..................................................................................................................... 70
4.7.3 E-Mail................................................................................................................................... 72
5. Search/Play 73
5.1 Search................................................................................................................................................ 73
5.2 Playback............................................................................................................................................. 77
6. Webviewer 78
7. Products Specifications 80

1. Overview
This chapter describes NVR overview, components and their terms and features.
This manual introduces a network video recorder (NVR) which monitors or record, controls images via a
network camera.
Multiple users may monitor video at the same time, and many cameras can be controlled simultaneously
by a manager. Also, through a PC or a smartphone, video might be monitored by transmitting video and
audio using a network.
The device features include the following:
Convenient UI from user’s viewpoint
IP camera input 16/32 channels
Providing H.264 and H.265 compression
Up to 4K real time recording
HDD information and status presentation
HDD overwriting.
High capacity back-up with USB 3.0
Simultaneous recoding and playing of 16/32 channels
Various search mode (time, event, back-up, thumbnail)
Various recording mode (manual, event, timed recording, panic recording)
Remote monitoring through a network viewer, a web viewer, and a mobile viewer

1.1 Package Contents
The device package contents consist of the following:
Note Please check all components involved.
Table 1-1 Package contents
No. Name No. Name
1 NVR 6 SATA cable
2 Power cord 7 SATA power cable
3 Mouse 8 HDD fixing screw
4 Quick guide 9 Rack mount bracket
5 Program CD 10 Bracket fixing screw
1.2 Part Description
Each part is listed in the below:
Figure 1-1 Name and Connection of each front section
Table 1-2 Name and Function of each front section
No. Name Function
1 Power status LED Pointing out device ON/OFF
2 Recording status
LED Pointing out recording in process
3 Network LED With a network viewer, pointing out network in connection
4 USB port USB port is connected for USB mouse or firmware upgrade, and data
back-up.

Figure 1-2 Name and Connection of rear section of 16ch, and 32ch NVR
Table 1-3 Name and Function of rear section of 16ch, and 32ch NVR
No. Name Function
1 LAN IP camera input port, IEEE802.3af PoE support
2 Line In Audio input port
3 Audio Out Audio output port
4 VGA VGA output port
5 HD Output HD output port
6 WAN Network connector
7 Alarm In/Out Alarm connector
8 RS485 RS-485 communication connector
9 e-SATA e-SATA storage connection connector
10 USB 3.0 USB 3.0 port is connected for data back-up

2. Installation
This chapter describes the way to install NVR.
When installing a device, connect rear of the device with each port on the basis of below connection map.
Figure 2-1 Connection map
The device starts first like below sequences:
1 Installing HDD
2 Connecting with an exterior device
3 Starting a system
4 Setting an earlier stage

2.1 Installing HDD
How to install HDD in the device:
Attention

Withdraw the mains plug before installing HDD to reduce the risk of injury or
electrical shock, or device malfunction.

Make sure to check the compatibility of HDD with the device.
1 Always switch off and unplug the unit.
2 Unscrew with a screw driver (+) and open the unit cover.
3 Unscrew HDD set screws of the bracket to disassemble.
4 Install HDD in the HDD bracket.
5 Fix the HDD-installed bracket with the unit.
6 Connect a data cable and power cable with HDD.
7 Close the cover and tighten screws.
2.2 Connecting with Exterior Device
How to connect each port to rear section of the unit:
1 Place the unit in a stable flat surface.
2 Make a room between front/rear sides of the device not to break connectors.
Warning
Do NOT install the device too close to the wall. Protrusive connects rear the unit
may be forcedly curved or pressed, which cause fires, electric shocks, or injury.
3 Check to switch off and unplug the unit.
Warning Make sure to withdraw the mains plug before installing the device.
4 Connect input ports of IP camera .
Note
Connecting a camera port with the unit automatically detects the camera.
5 Connect a audio input and output port with a mic and speaker.
Note
Assure regulations in the area whether recording to be legal or not.
6 Connect a monitor with VGA or HD output port.

7 Connect a network port.
8 Connect an alarm and RS485 device.
9 Connect an e-SATA storage.
10 Connect USB port for data back-up.
11 Supply the main power after completion.
Power Switch

2.3 Starting System
Power supply begins with system operation as follows:
1 Switching on initialize with below icons in order.
Note
Installing new HDD might take more initialize time.
2 With buzzer sounds, the start screen is presented.
3 In Log in screen, enter the ID, Password and press OK.
Note
Default ID/Password are admin/admin
Attention
Please change password after login due to security.
2.4 Setting Earlier Stage
First start of the system operates Easy Installation as follows:
1 Account
2 System
3 Network
4 Time/Date
5 Record

2.4.1 Account
How to set Account of Easy Installation:
1 Click the keyboard icon to set ID and Password users want.
2 With keyboard UI, set the ID and Password, and press OK.
3 Press the Save button to save newly set ID and Password.
4 Press Next button to end Account setting and move the next setting phase.

2.4.2 System
How to set the system of Easy Installation:
1 Set each item in System setting screen.
Language: Select system language.
Device Name: Enter the device name.
Keyboard ID: To identify device usages in controlling NVR with RS485 through a keyboard
Selecting the device ID. In case of simultaneous use of equipment, set ID with difference.
HD Output / VGA: Set resolution of a monitor connected to the device.
Note

Press Restore button in the below-right corner of the screen to cancel
changed set value.

Clicking Auto checkbox automatically sets the resolution.

As for using many NVRs, set ID with difference.
2 Press Save button to save set value.
3 Press Next to end System setting and move the next setting phase.

2.4.3 Network
How to set the network of Easy Installation:
1 Set each item in Network setting screen.
WAN Port: Select whether to use static IP or dynamic IP.
IP Address, Subnet Mask, Gateway, DNS, and Port: As for dynamic IP, enter information in each
space.
Note
Press Restore button in the below-right corner of the screen to cancel
changed set value.
2 Press Save button to save set value.
3 Press Next to end Network setting and move the next setting phase.

Time/Date
How to set the time/date of Easy Installation:
1 Set each item in Time/Date setting screen.
Network Time Sync: Select network for synchronizing with time server.
System Time: Not for synchronizing with network time server, set the device time; otherwise
(applying for Daylight saving time), select DST.
Time Zone: Select time zone for the system being installed.
DST Start/End: For applying Daylight saving time, set the application period.
Note
Press Restore button in the below-right corner of the screen to cancel changed
set value.
2 Press Save button to save set value.
3 Press Next to end Time/Date setting and move the next setting phase.

3. Live Screen Configuration
UI screen is configured like below figure.
Figure 3-1 UI Screen Configuration
Table 3-1 Items and Description of UI Screen Configuration
No. Item Description
1 Setup menu Setup menu is located in the corner of upper screen. See “4 Setup ” to
display detailed information about the setting menu.
2 Live screen Show live video of connected cameras.
3 Launcher menu Launcher menu is located in the corner of below screen. See “3.2 Live
Launcher ” to display detailed information about the launcher menu.
4 Quick menu Clicking the right button of a mouse displays Quick menu. See “3.3
Quick ” to display detailed information about the quick menu.