Comelit Nvr 2.0 User manual

I
NVR 2.0 IP 100 SERIES
Please read this manual thoroughly before use and keep it for future reference

II
Contents
Chapter 1 Installation........................................................................................................1
1.1 NVR Installation......................................................................................................1
1.2 Hard Disk Installation .............................................................................................1
Chapter 2 Getting Started .................................................................................................3
2.1 Start up and Shutdown...........................................................................................3
2.1.1 Start up.........................................................................................................3
2.1.2 Shutdown .....................................................................................................3
2.2 Login.......................................................................................................................3
2.3 Using Guide............................................................................................................4
2.4 Menu operation.......................................................................................................5
2.4.1 Begin setup..................................................................................................5
Chapter 3 Live View..........................................................................................................7
3.1 Introduction of Live View........................................................................................7
3.2 Operations in Live View Mode................................................................................7
3.3 Using the Mouse in Live View................................................................................9
3.4 Right tool bar........................................................................................................10
3.5 Channel Swap......................................................................................................11
Chapter 4 Playback.........................................................................................................12
4.1 Real-time Playback ..............................................................................................12
4.2 Playback by Normal Search.................................................................................12
4.2.1 Recording Playback...................................................................................12
4.2.2 Playback by Event Search.........................................................................14
4.2.3 Playback Pictures.......................................................................................14
4.2.4 Playback External File ...............................................................................15
Chapter 5 PTZ Controls..................................................................................................16
5.1 Configuring PTZ Settings.....................................................................................16
5.2 Setting PTZ Preset, Cruise & Pattern..................................................................16
5.2.1 Customizing Preset....................................................................................17
5.2.2 Customizing Cruise....................................................................................17
5.2.3 Customizing Pattern...................................................................................18
Chapter 6 Backup ...........................................................................................................19
6.1 Picture Backup .....................................................................................................19
6.2 Video File Backup.................................................................................................20
Chapter 7 Channel Setting..............................................................................................21
7.1 Adding IP Cameras...............................................................................................21
7.2 Channel Parameter..............................................................................................22
7.2.1 Display Setting...........................................................................................22
7.2.2 Video Encoding..........................................................................................23
7.2.3 Capture.......................................................................................................24
7.2.4 Motion.........................................................................................................24
7.2.5 Video Loss..................................................................................................26

III
7.2.6 Video Tampering ........................................................................................27
7.2.7 Video Mask.................................................................................................29
7.3 Schedule Setting..................................................................................................29
7.3.1 Configuring Parameters.............................................................................29
7.3.2 Timing Capture...........................................................................................30
7.4 Manual Operation.................................................................................................31
7.4.1 Manual Recording......................................................................................31
7.4.2 Capture.......................................................................................................32
7.4.3 Manual Alarm.............................................................................................32
7.5 Channel Grouping................................................................................................33
7.5.1 Structure.....................................................................................................33
7.5.2 Tour.............................................................................................................33
Chapter 8 Disk management..........................................................................................35
8.1 Storage Management...........................................................................................35
8.2 Disk Group............................................................................................................35
8.3 Advanced Configuration.......................................................................................36
8.4 Disk Location Map................................................................................................37
Chapter 9 System maintenance......................................................................................38
9.1 System Information ..............................................................................................38
9.1.1 Device Information.....................................................................................38
9.1.2 Stream Information.....................................................................................38
9.1.3 Online Users ..............................................................................................39
9.2 Log Information.....................................................................................................39
9.3 Configuration Management..................................................................................40
9.4 System Upgrade...................................................................................................40
9.5 Auto Maintenance.................................................................................................41
9.6 Network Monitoring ..............................................................................................41
9.6.1 Network Flow .............................................................................................41
9.6.2 Network Test...............................................................................................41
Chapter 10 System configuration....................................................................................43
10.1 Time Setting........................................................................................................43
10.2 Channel Zero Setting .........................................................................................43
10.2.1 Global Setting...........................................................................................43
10.2.2 Channel Setting........................................................................................44
10.3 Network Setting..................................................................................................44
10.3.1 Basic Setting............................................................................................44
10.3.2 DDNS Setting...........................................................................................45
10.3.3 Email Setting............................................................................................46
10.3.4 Advanced Setting.....................................................................................46
10.3.5 Management Platform..............................................................................47
10.4 Alarm Management............................................................................................48
10.4.1 Alarm Input...............................................................................................48
10.4.2 Alarm Output............................................................................................50
10.4.3 Abnormal Setting......................................................................................50

IV
10.4.4 Linkage Setting ........................................................................................51
10.5 User Management..............................................................................................52
10.6 PTZ Setting.........................................................................................................54
10.7 Device Setting ....................................................................................................55
Chapter 11 IntelligentAnalysis........................................................................................57
11.1 Brief Introduction.................................................................................................57
11.2 Enable SmartAnalysis........................................................................................57
11.3 Function Configuration .......................................................................................58
11.3.1 Detection Mode........................................................................................58
11.3.2 Behavior Analysis.....................................................................................58
11.3.7 Scene Transformation..............................................................................64
11.4Arming plan and linkage processing...................................................................65
11.4.1 Arming Plan..............................................................................................65
11.4.2 Alarm Linkage Setting ..............................................................................65
11.5 Smart Search......................................................................................................66
Statement
The instruction is for guidance only. Detailed information is in accordance with the
product.
The instruction may include some technical inaccuracies or typographical error thought it
is prepared with our every effort.
The product or procedures described in the instruction may be changed or updated at any
time without advance notice.
Screenshots used in the instruction are only for indications and explanations.
For any doubts or to request documents about latest procedures and complementary
notes, please consult with the after-sales service department.

NVR 2.0 User Manual (4
th
ed.)
1
Chapter 1 Installation
1.1 NVR Installation
During installation of the NVR：
Ensure the device is installed in a well-ventilated, dust-free environment.
The device is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
 Power down the device before connecting and disconnecting accessories and
peripherals.
1.2 Hard Disk Installation
Before you start:
Disconnect the power from the NVR before installing a hard disk drive (HDD). A
factory recommended HDD should be used for this installation.
Tools Required: Screwdriver.
Steps
：
(1) Remove the cover from the NVR by unfastening the screws on the rear panel.
(2) Insert the hard disk along the slot and fasten it.
(3) Connect the power & data cable to the NVR and HDD.

NVR 2.0 User Manual (4
th
ed.)
2
(4) Close the cover and fasten it with the screws.

NVR 2.0 User Manual (4
th
ed.)
3
Chapter 2 Getting Started
2.1 Start up and Shutdown
2.1.1 Start up
Plug in the power cord, press the power switch, the power indicator light should turn
bright. The device will begin to start. After the device starts up, the video output defaults to
multiple screen output mode.
2.1.2 Shutdown
Option 1: Press the power key on front panel to shutdown the device (if supported by
the device).
Option 2: Click Start→Shutdown→Confirm (Prompt: It is recommended to use this
way, in order to avoid damage to the device when suddenly powered off.)
Figure 2.1 Shutdown Menu
2.2 Login
If NVR first start-up or has logged out, you must login the device before operating the
menu and other functions, as shown in figure 2.2.
Figure 2.2 Login Interface
Steps:
1. Click Start button on the top of screen.
2. Click Login in the drop-down menu.
3. Input the Password in the pop-up interface (Default Password: blank).
4. Click Login to log in.

NVR 2.0 User Manual (4
th
ed.)
4
2.3 Using Guide
The Guide starts once login, as shown in figure 2.3.
Figure 2.3 Language Setting
Operating Guide
1）The Guide can walk you through some basic settings of the NVR. If you don’t want
to use the Guide at that moment, click the button. You can also choose to usethe Guide
next time by leaving the “Next time no longer display” check-box unchecked.
2）Click Next button to enter the Display Setting window, as shown in figure 2.4.
Figure 2.4 Resolution Setting
3）After the display setting, click Next button to enter the Network Setting window, as
shown in figure 2.5.

NVR 2.0 User Manual (4
th
ed.)
5
Figure 2.5 Network Setting
4）After the network setting, click Next button to enter the QR Code interface, as
shown in figure 2.6.
Figure 2.6 Qr Code
5）Click Finish to complete the Guide setup.
2.4 Menu operation
After the user login successfully, according to the interface of the upper toolbar to
perform associated settings,as shown in figure 2.7.
Figure 2.7 Menu operation
2.4.1 Begin setup
Click the icon, it will pop-up the interface as show in figure 2.8.

NVR 2.0 User Manual (4
th
ed.)
6
Figure 2.8 Begin setup
1) Logout: Click Logout button, can exit the current user.
2) Guide: Click Guide button, it will pop-up boot wizard setting interface, simply
configure language, display resolution, basic network parameters, and mobile phone app
to access the QR Code display.
3) Reboot: Click Reboot button and confirm, the device will automatically reboot.
4) Shutdown: Click Shutdown button and confirm, the device will automatically
shutdown.

NVR 2.0 User Manual (4
th
ed.)
7
Chapter 3 Live View
3.1 Introduction of Live View
Live view shows you the video image getting from each camera in real time. The NVR
will automatically enters live view mode when powered on, as shown in figure 3.1.
Figure 3.1 Live View Interface
Channel Live View Icons
In the live view mode, there are hide icons on the screen of each channel, which
shows when you move the mouse to the bottom of channel.
Table 3.1 Live View Icon description
Icons Description Icons Description
Open/Close PTZ Open/Close smart detection
display
Open/Close face display Capture
Open/Close Voice intercom Open/Close Channel Audio
Manual Recording Real-time Playback
3.2 Operations in Live View Mode
In live view mode, there are many functions provided. The functions are listed below.
(1) Real-time alarm information
On the top right corner, there is a real-time alarm information, as shown in figure 3.2.
Figure 3.2 Alarming

NVR 2.0 User Manual (4
th
ed.)
8
When you click , it will pop-up the alarm information, as shown in figure 3.3.
Figure 3.3 Alarm Information
When you click , it will hide the real-time alarm information.
(2) Other functions
Table 3.2 Other Function description
Icons functions Icons Description
1 Split Screen 4 Split Screen
6 Split Screen 8 Split Screen
9 Split Screen 16 Split Screen
25 Split Screen
36 Split Screen
64 Split Screen Sound Adjust
Cruise on Setting Linkage Preview
Display Main Stream Page Up/Page Down
Last/Next Group Capture all preview channel
All preview channel manual record setting

NVR 2.0 User Manual (4
th
ed.)
9
3.3 Using the Mouse in Live View
Figure 3.4 Right Click Menu
Table 3.3 Right Click Function description
Name Description
Full Screen Quick enter full screen mode.
Tour On/Off Open/Close cruise.
Start Recording On/Off Open/Close manual record.
Channel Connecting Quick enter IP Camera Management interface.
PTZ Ctrl Open
Last Screen Switch to the previous screen.
Next Screen Switch to the next screen.
4 Split Screen Select and enter 4 Split Screen mode.
6 Split Screen Select and enter 6 Split Screen mode.
8 Split Screen Select and enter 8 Split Screen mode.
9 Split Screen Select and enter 9 Split Screen mode.
16 Split Screen Enter 16 Split Screen mode.
25 Split Screen Enter 25 Split Screen mode.
36 Split Screen Enter 36 Split Screen mode.
64 Split Screen Enter 64 Split Screen mode.

NVR 2.0 User Manual (4
th
ed.)
10
3.4 Right tool bar
(1) Images play mode
There are three kinds of play mode, as shown in figure 3.5. Preview pictures can
be showed according to "Device List", "Structure" and "Tour". The default play mode
is "Device List". Note that, “Structure” and "Tour" can be used only when they are
configured in advance, see below the detailed operation, channel configuration
section.
Figure 3.5 Device List
(2) Disk information
Can view in real-time the hard disk status, it’s convenient to view when connect
multiple hard disk, as shown in figure 3.6.
Figure 3.6 HDD info
(3) Video parameter
May revise the brightness, contrast, saturation and hue of the channel that the
current mouse selected, one click to restore the default value when necessary, as
shown in figure 3.7.

NVR 2.0 User Manual (4
th
ed.)
11
Figure 3.7 Video
（4）PTZ/Preset/CRZ/Track
Please confirm whether the related parameters setting is correct before control
the PTZ. After setting up parameters, select the channel to be controlled in the
preview interface, then control the direction of the lens, focal length, focus, aperture
amplification and narrow in PTZ operation interface and adjust the speed of PTZ, as
shown in figure 3.8. See below the detailed operation of PTZ control part.
Figure 3.8 PTZ
3.5 Channel Swap
Select a channel, drag to another channel, it will pop-up prompt dialog box, as shown
in figure 3.9.
Figure 3.9 Channel Swap
There are three ways to exchange channels：
(1) Exchange channel connection, at the same time, all configuration swaps;
(2) Exchange channel order, exchange the preview position, the device list
information changes at the same time;
(3) Exchange window position, exchange the preview position, the device list
information no change at the same time.

NVR 2.0 User Manual (4
th
ed.)
12
Chapter 4 Playback
4.1 Real-time Playback
Purpose:
Playback the recorded video files of a specific channel in the live view mode.
Steps:
Choose a channel in live view mode and click the button in the bottom of the
channel, as shown in figure 4.1.
Figure 4.1 Real Time Playback
4.2 Playback by Normal Search
4.2.1 Recording Playback
Click icon to enter the Playback interface, as shown in figure 4.2.
Figure 4.2 Normal Playback Interface

NVR 2.0 User Manual (4
th
ed.)
13
Playback by time
Purpose:
Playback video files recorded in specified time duration. Multi-channel simultaneous
playback is supported.
Steps:
1）Enter playback interface.
2）Check the check-box of channel(s) in the channel list and then double-click to
select a date on the calendar.
3）Click the button to start playback, as shown in figure 4.3.
Figure 4.3 Video Playback
Note:
If there are record files for that camera in that day, in the calendar, the icon for that day
is displayed as . Otherwise it is displayed as
Playback Interface
You can use the toolbar in the bottom part of Playback interface to control playing
progress, as shown in figure 4.4.
Figure 4.4 Playback Toolbar
Table 4.1 Detailed Explanation of Playback Toolbar
Button Operation Button Operation
Play/Stop
Stop
Playback forward
Playback backward
Single frame
30 seconds forward/backward
Speed Down
Speed Up
1 Split Screen
4 Split Screen
6 Split Screen
8 Split Screen
9 Split Screen
16 Split Screen
Page Up/Page Down Backup

NVR 2.0 User Manual (4
th
ed.)
14
Capture Hide/Show the progress bar
Sound Adjust
4.2.2 Playback by Event Search
Purpose:
Playback record files on one or several channels searched out by event type (e.g.
alarm detection, motion).
Steps:
1）Enter the Playback interface.
2）Select the Retrieving type: There are many types you can select, such as Count
Alarm, Motion,Across the line, Regional, Alarm detection and object left/Loss etc. .
3）Click the Query button to get the search result information.
4） Click button to playback the file.
4.2.3 Playback Pictures
Purpose:
The captured pictures stored in the HDDs of the device can be searched and viewed,
as shown in figure 4.5.
Figure 4.5 Picture Playback
Steps:
1）Enter playback interface.
2）Select playback modes: Snapshot.
3）Select Search by day or Search by time.
4）Select Picture source: IPC Snapshot (preview snapshot) or Playback Snapshot.
5）Choose Condition: Meet random or Meet all.
6）Select Retrieving type.
7）Select Search Channel.
8）Click Query button to search for the capture picture.
9）Check the check-box after the picture listed, then click to view the picture.
10）The toolbar in the bottom of playback interface can be used to control playing
process.

NVR 2.0 User Manual (4
th
ed.)
15
Table 4.2 Detailed Explanation of Playback Toolbar
Button Function Button Function
Play/Stop
Stop
Next picture
Last picture
Note:
Click the check-box of the picture listed, then click Backup button, can enter the
Snapshot back-up interface, as shown in figure 4.6.
Figure 4.6 Picture Backup Interface
4.2.4 Playback External File
Purpose:
Perform the following steps to look up and playback files in the external devices, as
shown in figure 4.7.
Figure 4.7 External File Playback Interface
Steps:
1）Enter the playback interface.
2）Select playback modes: External file.
3）Click the Refresh button to refresh the file listed.
4）Select and click the button to playback it.And you can adjust the playback
speed by clicking and .

NVR 2.0 User Manual (4
th
ed.)
16
Chapter 5 PTZ Controls
5.1 Configuring PTZ Settings
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ
parameters should be done before you control the PTZ camera.
Steps:
1）Enter the PTZ Setting interface, as shown in figure 5.1.
Figure 5.1 PTZ General Setting Interface
2）Channel: Choose the channel.
3）Protocol: Choose the protocol for your PTZ.
4）Decoder Address: Choose the decoder address.
5）Baud Rate: Select the baud rate.
6）Data Bit: Select the data bit.
7）Stop Bit: Select the stop bit.
8）Parity: Select the verify, Non Parity by default.
9）Flow Control: Select the stream control, No Flow Control by default.
10） Click Save button to save the settings.
5.2 Setting PTZ Preset, Cruise & Pattern
Before you start:
Please make sure that the preset, cruise and pattern should be supported by PTZ
protocols, as shown in figure 5.2.