Comm-Tec UP-82TS User manual

UP-82TS
8x2 HDMI 2.0 Seamless Matrix Switcher
All Rights Reserved
Version: 2019V1.5
User Manual

Seamless Switcher
Comm-tec Srl 2 www.comm-tec.it
Preface
Read this user manual carefully before using the product. Pictures shown in this manual
are for reference only. Different models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till May,
2019. In the constant effort to improve the product, we reserve the right to make functions
or parameters changes without notice or obligation. Please refer to the dealers for the
latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. It has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void the
user’s authority to operate the equipment.
Manufacture
This product is manufactured by:
SHENZHEN PTN Electronics Limited
Add: B6, JinXiongDa Technology Park, HuanGuan Road South 105th
GuanLan Block, LongHua New District
ShenZhen City, 518110, China
Tel: [phone] - Fax: [phone]
Service: [email protected]
Sales:[email protected]
Website:www.ptn-electronics.com

Seamless Switcher
Comm-tec Srl 3 www.comm-tec.it
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using the
device. Save this manual for further reference.
⚫Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to
persons.
⚫Do not dismantle the housing or modify the module. It may result in electrical shock or
burn.
⚫Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
⚫Refer all servicing to qualified service personnel.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
⚫Do not put any heavy items on the extension cable in case of extrusion.
⚫Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
⚫Install the device in a place with fine ventilation to avoid damage caused by overheat.
⚫Keep the module away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
⚫Do not twist or pull by force ends of the cable. It can cause malfunction.
⚫Do not use liquid or aerosol cleaners to clean this unit.Always unplug the power to the
device before cleaning.
⚫Unplug the power cord when left unused for a long period of time.
⚫Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

Seamless Switcher
Comm-tec Srl 4 www.comm-tec.it
Table of Contents
1. Product Introduction ...................................................................................................6
1.1 Features............................................................................................................6
1.2 Package List ..................................................................................................... 7
2. Specification...............................................................................................................8
2.1 UP-82TS Matrix Switcher..................................................................................8
2.2 TPUH610A Extender Kit.................................................................................. 10
3. Panel Description .....................................................................................................11
3.1 Matrix Switcher Front Panel.............................................................................11
3.2 Matrix Switcher Rear Panel............................................................................. 12
3.3 Transmitter Front and Rear Panel................................................................... 13
3.4 Receiver Front and Rear Panel....................................................................... 14
4. System Connection ..................................................................................................15
4.1 Usage Precaution ........................................................................................... 15
4.2 System Diagram ............................................................................................. 15
5. Button Control ..........................................................................................................16
5.1 Manual Switching............................................................................................ 16
5.2 Auto Switching ................................................................................................ 16
5.3 Resolution Selection ....................................................................................... 17
5.4 Sound Volume Control.................................................................................... 17
6. IR Remote Control....................................................................................................18
7. GUI Control ..............................................................................................................19
7.1 Video Switching............................................................................................... 20
7.2 Resolution Selection ....................................................................................... 21
7.3 Audio Control .................................................................................................. 22
7.4 Configuration................................................................................................... 23
7.4.1 PoC Setting...........................................................................................23
7.4.2 EDID Management................................................................................24
7.4.3 Relay Control ........................................................................................25
7.5 CEC Control.................................................................................................... 26

Seamless Switcher
Comm-tec Srl 5 www.comm-tec.it
7.6 Tags Setting .................................................................................................... 29
7.7 RS232 Control ................................................................................................ 30
7.8 Network Setting............................................................................................... 32
7.9 Password Setting............................................................................................ 33
7.10 GUI Upgrade................................................................................................. 34
8. RS232 Control..........................................................................................................35
8.1 RS232 Control Software ................................................................................. 35
8.2 RS232 Communication Command.................................................................. 37
8.2.1 Device Control.......................................................................................37
8.2.2 Source Switching ..................................................................................38
8.2.3 Preset Setting........................................................................................39
8.2.4 Output Resolution Setting .....................................................................39
8.2.5 Audio Control.........................................................................................40
8.2.6 EDID Management................................................................................41
8.2.7 Relay Control ........................................................................................41
8.2.8 VGA Output Image Adjustment .............................................................42
8.2.9 Switcher Baud Rate Setting ..................................................................42
8.2.10 CEC Control........................................................................................43
8.2.11 Third-party Device Control...................................................................45
9. OSD Control.............................................................................................................47
10. Firmware Upgrade..................................................................................................50
11. Panel Drawing........................................................................................................51
12. Troubleshooting and Maintenance..........................................................................53
13. Customer Service...................................................................................................54

Seamless Switcher
Comm-tec Srl 6 www.comm-tec.it
1. Product Introduction
Thanks for choosing the UP-82TS 8x2 multi-format seamless presentation matrix switcher
with one TPUH610A extender kit! The matrix switcher simplifies meeting room and
presentation space system integration by providing one HDBaseT input, four HDMI inputs,
one VGA input, one DP input, one USB-C input, one HDBaseT output and one HDMI
output. It also provides external audio inputs to be embedded in HDBaseT, HDMI and VGA
video inputs respectively. Moreover, it provides MIX audio input for global audio.
The matrix switcher provides true 4K scaling up to 4K@60Hz@4:4:4. Both inputs and
outputs are capable of providing 4K@60Hz@4:4:4 signals. The HDBaseT input and output
provide an innovative solution with VLC technology, allowing transmission of HDMI 2.0
signals over a CATx cable while ensuring very high, original image quality. It is designed for
use with the TPUH610A extender kit. The USB-C input is ideal forAV interfacing with
newer MacBook, Chromebook, and Windows PC, as well as smart phones and tablets.
The matrix switcher supports auto switching on HDMI, HDBaseT and HDMI loop outputs
based on TMDS activity signals sensing. It also allows users to control system functionality
via Web GUI, RS232, IR and CEC.Additionally, users can control relay device such as the
rise and fall of projector screen over RELAY ports.
The matrix switcher is designed to be the central component of AV system. It is ideal for
applications where multiple signals with different resolutions must be optimized for displays.
It is also suitable for presentation spaces where two displays are needed.
1.1 Features
⚫8x2 HDMI 2.0 seamless presentation switcher with matrix outputs.
⚫HDMI 2.0 and HDCP 2.2 compliant. The video resolution can up to 4K@60Hz 4:4:4.
⚫Supports video resolution down-scaling and up-scaling, 1080P, 1920x1200P, 4K@30Hz,
4K@60Hz can be selected for HDMI and HDBaseT outputs.
⚫Supports Auto switching.
⚫Features a mirrored HDMI output for HDBaseT output.
⚫Visually lossless video de-compression and compression for HDMI signals transmission
up to 40m at 4K and 70m at 1080P on HDBaseT input and output.
⚫HDBaseT input and output support 24V PoC.
⚫External balanced audio inputs can be embedded in one HDBaseT input and two HDMI
video inputs respectively.
⚫Provides two groups of audio outputs (balanced audio and digital SPDIF audio) for
audio de-embedding.
⚫Supports MIX audio input and its volume control.

Seamless Switcher
Comm-tec Srl 7 www.comm-tec.it
⚫Supports HDMI output, HDBaseT output audio control.
⚫Controllable via RS232 local and pass-through, IR local and pass-through, TCP/IP, relay,
CEC and on OSD.
1.2 Package List
Matrix Switcher
⚫1x UP-82TS 8x2 HDMI 2.0 Seamless Matrix Switcher
⚫2x Mounting Ears with 6 Screws
⚫4x Plastic Cushions
⚫1x IR Remote
⚫1x IR Receiver
⚫3x 3-pin Terminal Blocks
⚫7x 5-pin Terminal Blocks
⚫1x Power Adaptor (24V DC 5A)
Extender Kit
⚫1x TPUH610AT HDBaseT Transmitter
⚫1x TPUH610AR HDBaseT Receiver
⚫4x Mounting Ears with 8 Screws
⚫8x Plastic Cushions
⚫1x 3-pin Terminal Block
⚫1x RS232 Cable (3-pin to DB9)
⚫1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

Seamless Switcher
Comm-tec Srl 8 www.comm-tec.it
2. Specification
2.1 UP-82TS Matrix Switcher
Video Input
Video Input
(1) HDBaseT, (4) HDMI, (1) Display Port, (1) VGA, (1) USB-C
Video Input Connector
(1) RJ45, (4) Type-A female HDMI, (1) Type-A female DisplayPort,
(1) 15-pin female VGA, (1) Type-C USB 3.0
Video input Video Resolution
HDBaseT: Up to 4Kx2K@60Hz 4:4:4
HDMI: Up to 4Kx2K@60Hz 4:4:4
DP: Up to 4Kx2K@60Hz 4:4:4
VGA: Up to 1920x1200 (50/60Hz)
USB-C: Up to 4Kx2K@30Hz
Video Output
Video Output
(2) HDMI, (1) HDBaseT
Video Output Connector
(2) Type-A Female HDMI, (1) RJ45
Video output Video Resolution
HDMI: Up to 4Kx2K@60Hz 4:4:4
HDBaseT: Up to 4Kx2K@60Hz 4:4:4
HDMI Version
2.0
HDCP Version
2.2
Audio Input
Audio Input
(1) External balanced audio (L+R) for 1-HDBT input port
(1) External balanced audio (L+R) for 2-HDMI input port
(1) External balanced audio (L+R) for 3-HDMI input port
(1) Stereo auxiliary audio for 6-VGA input port
(1) Balanced MIX audio
Audio Input Connector
(4) 5-pin terminal blocks (1) 3.5mm jack
Frequency Response
20Hz –20KHz, ±3dB
Max Input Level
2.0Vrms ± 0.5dB. 2V = 16dB headroom above - 10dBV (316mV) nominal
consumer line level signal.
Input Impedance
>10KΩ
Audio Output
Audio Output
(1) Balanced audio (L+R) for 1-HDMI output audio de-embedding
(1) Digital SPDIF audio (L+R) for 1-HDMI output audio de-embedding
(1) Balanced audio (L+R) for 2-HDBT output audio de-embedding
(1) Digital SPDIF audio (L+R) for 2-HDBT output audio de-embedding
Audio Output Connector
(2) 5-pin terminal blocks (2) Toslink connectors
Frequency Response
20Hz –20KHz, ±3dB
Max Output Level
2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV) nominal
consumer line level signal

Seamless Switcher
Comm-tec Srl 9 www.comm-tec.it
THD+N
< 0.05% (-80dB), 20Hz –20KHz bandwidth, 1KHz sine at 0dBFS level (or
max level)
SNR
> 80dB, 20Hz - 20KHz bandwidth
Crosstalk Isolation
> 70dB, 10KHz sine at 0dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3dB, 1KHz sine at 0dBFS level (or max level before clipping)
Frequency Response
Deviation
< ± 0.5dB 20Hz - 20KHz
Output Load Capability
1KΩ and higher (Supports 10x paralleled 10KΩ loads)
Stereo Channel Separation
>70dB@1KHz
Noise Level
-80dB
Control Part
Control Port
(1) RS232, (2) RELAY 1-2, (1) IR EYE, (2) IR IN, (1) IR OUT, (1) TCP/IP,
(1) FIRMWARE
Control Connector
(3) 3-pin terminal blocks, (4) 3.5mm jacks, (1) RJ45, (1) Type-AUSB
General
Transmission Mode
HDBaseT
Transmission Distance
HDBaseT Input/Output:
1080P@60Hz ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
Bandwidth
18Gbps
Operation Temperature
-10℃~ +55℃
Storage Temperature
-25℃~ +70℃
Relative Humility
10%-90%
External Power Supply
Input: AC 100~240V, 50/60Hz; Output: 24V DC 5A
Power Consumption
85W (Max)
Dimension (W*H*D)
436.4mm x 44mm x 356.5mm
Net Weight
2.87KG

Seamless Switcher
Comm-tec Srl 10 www.comm-tec.it
2.2 TPUH610A Extender Kit
Transmitter (TX)
Input
(1) HDMI
Input Connector
(1) Type-A female HDMI
Output
(1) HDBT OUT
Output Connector
(1) RJ45
Control
(1) IR IN, (1) IR OUT, (1) RS232
Control Connector
(2) 3.5mm jacks, (1) 3-pin terminal block
Video Resolution
Up to 4Kx2K@60Hz 4:4:4 8bit
Receiver (RX)
Input
(1) HDBT IN
Input Connector
(1) RJ45
Output
(1) HDMI
Output Connector
(1) Type-A female HDMI
Control
(1) IR IN, (1) IR OUT, (1) RS232
Control Connector
(2) 3.5mm jacks, (1) 3-pin terminal block
Video Resolution
Up to 4Kx2K@60Hz 4:4:4 8bit
General
Transmission Mode
HDBaseT
Transmission Distance
1080P@60Hz ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
HDMI Version
2.0
HDCP Version
2.2
Bandwidth
18Gbps
Power Consumption
14W (max)
Operation Temperature
-10℃~ +55℃
Storage Temperature
-25℃~ +70℃
Relative Humility
10%-90%
External Power Supply
Input Power: 12V DC 2A or Power over Cable (PoC),
AC Adaptor Input Power: 100~240VAC, 50/60Hz
Dimension (W*H*D)
115mm x 16mm x 84mm
Net Weight (g)
Transmitter/Receiver: 150g

Seamless Switcher
Comm-tec Srl 11 www.comm-tec.it
3. Panel Description
3.1 Matrix Switcher Front Panel
①Power LED: The LED illuminates red the device is powered on.
②SOURCE: Total nine buttons with blue backlight.
⚫1-HDBT input selector / Left Key for On Screen Display control (OSD).
⚫2-HDMI input selector / Right Key for OSD.
⚫3-HDMI input selector / Up Key for OSD.
⚫4-HDMI input selector / Down Key for OSD.
⚫5-HDMI input selector.
⚫6-VGA input selector.
⚫7-DP input selector.
⚫8-USB-C input selector / Enter key for OSD.
⚫Auto switching mode selector. Press this to enter or exit auto switching mode. /
Press and hold it at least 2 seconds to enable OSD menu.
③OUTPUTS: Two buttons with blue backlight.
⚫1-HDMI output selector.
⚫2-HDBT output selector.
④RESOLUTION: Two output video resolution selectors. Press the 1.HDMI or 2.HDBT
button repeatedly to cycle through the four video resolutions. A series of four LEDs,
one of which illuminates blue to indicate which resolution is selected.
⑤VOLUME:
⚫Press the volume knob in to toggle among MIX, HDMI OUT and HDBT OUT audio
control, and the corresponding LED will illuminate blue.
⚫Rotate the knob to increase or decrease the volume of the selected audio.
⚫Press and hold the knob at least three seconds to mute the selected audio. Rotate
the knob to unmute.
12345

Seamless Switcher
Comm-tec Srl 12 www.comm-tec.it
3.2 Matrix Switcher Rear Panel
①INPUT: Total eight video inputs, five audio inputs and one IR input.
⚫1-HDBT: RJ45 port to connect the TPUH610AT transmitter to receive AV signal, IR
and RS232 control signal, and one external balanced audio input (5-pin) can be
embedded in the HDBT video. In addition, the HDBT input supports 24V PoC.
⚫2-HDMI: Type-A female HDMI port to connect the HDMI source. One external
balanced audio input (5-pin) can be embedded in the HDMI video.
⚫3-HDMI: Type-A female HDMI port to connect the HDMI source. One external
balanced audio input (5-pin) can be embedded in the HDMI video.
⚫4-HDMI: Type-A female HDMI port to connect the HDMI source.
⚫5-HDMI: Type-A female HDMI port to connect the HDMI source.
⚫6-VGA: 15-pin female VGA port to connect the VGA source. One stereo auxiliary
audio input (3.5mm jack) can be embedded in the VGA video.
⚫7-DP:Type-Afemale DP port to connect the DP source.
⚫8-USB-C: Type-C USB port to connect the device with SlimPort output, e.g.
Macbook.
⚫IR IN: 3.5mm jack to connect the IR receiver for IR pass-through.
⚫MIX: 5-pin terminal block to connect the audio source for global audio mixing.
②OUTPUT:
⚫1-HDMI: Type-A female HDMI port to connect the video display.
⚫2-HDMI: Type-A female HDMI port to connect the video display.
⚫2-HDBT: RJ45 port to connect the TPUH610AR receiver to transmit AV signal, IR
and RS232 control signal. The HDBT output supports 24V PoC.
Note: The 2-HDMI and 2-HDBT ports output the same signal.
⚫IR IN: 3.5mm jack to connect the IR receiver for IR pass-through.
⚫IR OUT: 3.5mm jack to connect the IR emitter for IR pass-through.
③AUDIO OUTPUT:
6. VGA 8. USB-CAUDIO 7. DP DC 24V
OUTPUTS
2. HDBT IR IN 1. HDMI
TCP/IP
CONTROL
IR EYE FIRMWARE
1
L R L R
IR OUT
2. HDMI
5. HDMI4. HDMI
2. HDMI 3. HDMI 1. HDBT
IR IN
L R L RL R
MIX
L R
INPUTS
2RS232
Tx Rx
RELAY1
NO COM N C
RELAY2
NO COM N C
AUDIO OUT
1
25
34

Seamless Switcher
Comm-tec Srl 13 www.comm-tec.it
⚫1: One balanced audio output (5-pin) and one digital SPDIF audio output for
1-HDMI output audio de-embedding.
⚫2: One balanced audio output (5-pin) and one digital SPDIF audio output for
2-HDBT output audio de-embedding.
④CONTROL:
⚫RS232: 3-pin terminal block to connect the control device (e.g. PC) to control the
switcher by sending RS232 commands. It also supports RS232 pass-through
control.
⚫RELAY 1-2: Two 3-pin terminal blocks to connect the relay devices (e.g. projector
screen).
⚫IR EYE: 3.5mm jack to connect IR receiver to control the switcher by the IR
remote.
⚫TCP/IP: RJ45 port to connect the control device (e.g. PC) to control the switcher by
GUI.
⚫FIRMWARE: Type-A USB port for firmware upgrade.
⑤DC 24V: DC barrel connector for the power adapter connection.
3.3 Transmitter Front and Rear Panel
①MODE SWITCH: Put the Mode switch in the CTRL position for normal operation and
to allow RS232 control pass-through. Put the switch in the UPDATE A position to
update the Valens IC program. Finally, put the switch in the UPDATE B position to
update the compression IC program.
②POWER LED: The LED illuminates red when power is applied.
③HDMI IN: Type-Afemale HDMI port to connect the HDMI source.
④RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a device
to be controlled by RS232 commands.
⑤IR IN: 3.5mm jack to connect the IR receiver for IR pass-through.
⑥IR OUT: 3.5mm jack to connect the IR emitter for IR pass-through.
CTRL
UPDATE B UPDATE A
Tx Rx DC 12V
IROUT IRIN
HDBT OUT
HDMIIN
12345678

Seamless Switcher
Comm-tec Srl 14 www.comm-tec.it
⑦HDBT OUT: RJ45 port to connect the HDBT IN port of switcher by CATx Ethernet
cable.
⑧DC 12V: DC barrel connector for the power adapter connection.
3.4 Receiver Front and Rear Panel
①MODE SWITCH: Put the Mode switch in the CTRL position for normal operation and
to allow RS232 control pass-through. Put the switch in the UPDATE A position to
update the Valens IC program. Finally, put the switch in the UPDATE B position to
update the compression IC program.
②POWER LED: The LED illuminates red when power is applied.
③HDMI OUT: Type-A female HDMI port to connect the display device.
④RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a device
to be controlled by RS232 commands.
⑤IR IN: 3.5mm jack to connect the IR receiver for IR pass-through.
⑥IR OUT: 3.5mm jack to connect the IR emitter for IR pass-through.
⑦HDBT IN: RJ45 port to connect the HDBT OUT port of switcher by CATx Ethernet
cable.
⑧DC 12V: DC barrel connector for the power adapter connection.
CTRL
UPDATE B UPDATE A
DC 12V
Tx Rx
HDMIOUT
HDBT IN
IROUT
IRIN
12345678

Seamless Switcher
Comm-tec Srl 15 www.comm-tec.it
4. System Connection
4.1 Usage Precaution
⚫Make sure all components and accessories included before installation.
⚫System should be installed in a clean environment with proper temperature and
humidity.
⚫All of the power switches, plugs, sockets, and power cords should be insulated and
safe.
⚫All devices should be connected before power on.
4.2 System Diagram
6. VGA 8. USB-CAUDIO 7. DP DC 24V
OUTPUTS
2. HDBT IR IN1. HDMI
TCP/IP
CONTROL
IR EYE FIRMWARE
1
L R L R
IR OUT2. HDMI5. HDMI4. HDMI2. HDMI 3. HDMI1. HDBTIR IN
L R L RL R
MIX
L R
INPUTS
2RS232
Tx Rx
RELAY1
NO COM NC
RELAY2
NO COM NC
AUDIO OUT
Blu-Ray DVD
HDMI 2.0 Transmitter
Game Console
PC
MacBooK
Cellphone
RS232
Tx Rx
IR
STEREO BRIDGE
MONO
LR
MIC
LINE48V
MIC 1 2
INPUTS
Audio Player
Speaker Amplifier Soundbar
HDTV Project ScreenProjector HDTV HDMI 2.0 Receiver
5.HDMI4.HDMI 6. VGA
OK
2.HDBT BLACK
Wireless Router iPad
IR
Receiver
Remote
Central
Control System
4K 40m,1080P 70m
4K 40m,1080P 70m
DP:
VGA:
HDMI:
Control:
Ethernet:
Audio:
HDBaseT:
USB-C:

Seamless Switcher
Comm-tec Srl 16 www.comm-tec.it
5. Button Control
5.1 Manual Switching
When the switcher is in manual switching mode, the AUTO button LED goes out. Please
follow the below steps to switch input source to output channel.
1) Press any one of eight input buttons to select input source, and the corresponding
button LED turns blue.
2) Press either 1-HDMI or 2-HDBT output button to select output channel, and the
corresponding button LED turns blue.
3) Press the input button again to confirm switching setting, otherwise, it will automatically
confirm after three seconds.
5.2 Auto Switching
Please follow the below steps to enable auto switching mode for 1-HDMI or 2-HDBT
output.
1) Press AUTO, and the button LED turns blue.
2) Press either 1-HDMI or 2-HDBT output button, and the corresponding button LED turns
blue.
3) Press AUTO button again to confirm the setting, otherwise, it will automatically confirm
after three seconds.
4) Repeat the above three steps can exit auto mode, but the input source will remain the
current setting.
Note: The AUTO button LED illuminates blue when the 1-HDMI output is in auto mode or
the 2-HDBT output in auto mode.
When in auto mode, the switcher will switch according to the following rules:
⚫The switcher will switch to the first available active input starting at input 1 to 8.
⚫New input: The switcher will automatically select the new input once detecting a new
input.
⚫Reboot: If power is restored to the switcher, it will automatically reconnect the input
before powered off.
⚫Source removed: When an active source is removed, the switcher will switch to the first
available active input starting at 1-HDBT input.
⚫In auto mode, the input source also can be switched by the manual switching steps.

Seamless Switcher
Comm-tec Srl 17 www.comm-tec.it
5.3 Resolution Selection
Press the 1.HDMI or 2.HDBT button on RESOLUTION area repeatedly to cycle through
the four video resolutions.A series of four LEDs, one of which illuminates blue to indicate
which resolution is selected.
5.4 Sound Volume Control
Press volume knob to choose MIX, HDMI OUT or HDBT OUT audio needs to be adjusted,
the corresponding LED will turn blue and keep on.
⚫Adjusting the knob in clockwise direction to increase sound volume.
⚫Adjusting the knob in anti-clockwise direction to decrease sound volume.
⚫Press and hold the knob at least three seconds to mute the selected audio. Rotate the
knob to unmute.

Seamless Switcher
Comm-tec Srl 18 www.comm-tec.it
6. IR Remote Control
Connect IR receiver to the IR EYE port, the switcher can be controlled by the following IR
remote.
①Select input source
②Select output channel
③Press AUTO to enable auto switching mode,
and then select output channel.
④Press BLACK, and then select output
channel to make it output black screen.
⑤Enable/Disable OSD menu.
⑥Confirm and Navigation buttons: OK, UP,
DOWN, LEFT and RIGHT for OSD menu.
⑦Return to the previous OSD menu.
⑧MIX input audio control: Mute, Volume Down
and Volume Up.
⑨HDMI output audio control: Mute, Volume
Down and Volume Up.
⑩HDBT output audio control: Mute, Volume
Down and Volume Up.
5. HDMI4. HDMI 6. VGA
OK
2. HDBT BLACK
1
2
5
8
9
7
10
6
3
4

Seamless Switcher
Comm-tec Srl 19 www.comm-tec.it
7. GUI Control
The switcher can be controlled via TCP/IP. The default IP settings are:
IP Address:
192.168.0.178
Subnet Mask:
255.255.255.0
Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage:
Username: admin
Password: admin
Type the user name and password, and then click Login to enter the section for video
switching.

Seamless Switcher
Comm-tec Srl 20 www.comm-tec.it
7.1 Video Switching
⚫HDMI OUTPUT: Switch the selected input source to HDMI output. Click AUTO to
enable/disable auto switching mode.
⚫HDBT OUTPUT: Switch the selected input source to HDBT output. Click AUTO to
enable/disable auto switching mode.
⚫Preset: Save the current routing status to preset 1~5.