Commando FM-760 User manual

APR/16/2002
6979 USA 1
COMMANDO
MODELFM-760
REMOTE ENGINE STARTER
WITH ALARM SYSTEM
INSTALLATION MANUAL

APR/16/2002
6979 USA 2
INTRODUCTION
INSTALLER WARNINGS
This Remote Starter with Security and Keyless Entry System is designed to be installed on fuel injected
vehicles with an automatic transmission ONLY.
Never install this remote starter on a manual transmission vehicle.
This system must be installed and wired through a safety switch it will not start in any forward or reverse
gear.
Some automatic transmission vehicle [mainly older GM vehicles with a purple starter wire] have a
mechanical-type park safety switch instead of electrical safety switch. The mechanical type does not
interrupt the starter circuit when the transmission is any gear and does not offer the 100% level of safety
required for remote starting purposes. Therefore, our system should never be installed on any vehicle that
uses a mechanical type park safety switch.
Once you install this system, you must verify that the vehicle will not start any forward or reverse gear.
Regardless of the type of vehicle.
Read operation manual for operating and programming routine.
Do not install any component near the brake, gas pedal or steering linkage.
Some vehicles have a factory installed transponder immobilizer system that can severely complicate the
installation. There is possibility that this system can not be installed on some immobilizer equipped
vehicles.
Most vehicles have an SRS air bag system. Use extreme care and do not probe any wires of the SRS
system.
Disconnect the car battery before connecting work on the vehicle.
Check behind panels before drilling any holes. Ensure that no wiring harness or other components are
located behind the panels that would otherwise be damaged.
Use conventional crimp lock, bullet on any wiring. Poor wiring, i.e. taped joints will possibly introduce
unreliability into the alarm system and may result in false alarms or incorrect operation.
Install wiring neatly under carpets or behind trim to prevent possible damage to wires.
For the wire operates the current more than 10A. We suggest soldering all connection point. Do not use
crimp lock type connectors or wire nuts.

APR/16/2002
6979 USA 3
INSTALLATION DIAGRAM

APR/16/2002
6979 USA 4
5. Pink: Ignition 2 output
H6
8 Pin Black
Connector
For Input
Connection
H 1
6 Pin
White
H 2
5 Pin
White
H 3
2 Pin
White
H 4
3 Pin
Black
H 5
3 Pin
Brown
H 6
8 Pin
Black
V
ALET
SWITCH
H 9
6Pin
White
H 10
3 Pin
Green
H 11
2 Pin
Blue
1. Red/White: Parking Light Relay Power input
2. White: Parking Light Relay Output
3. Black: Ground to Vehicle Frame
4. Brown: Positive Output to Siren
5. Red: +12V Input
Two Way
Transceive
r
Antenna
LED
Indicator
3A Fuse
15A Fuse
2. Red: +12V Input
3. Red: +12V Input
4. Yellow: Ignition 1 output
1. Violet: Starter Output
20
A
Fuse
20
A
Fuse
6. Brown: ACC/Heater Output
H 8
4 Pin
Orange
H9
6 Pin White
Connector
for Output
Connection
Optional
Pager
(Knock)
Sensor
Optional
Temperature
Sensor
3. Green: (-) Lock Pulse. Or (+)Unlock Pulse. 1. Blue:
(
-
)
Unlock Pulse. Or
(
+
)
Lock Pulse.
H 7
3 Pin
White
4. Red: +12 Volts power 3. Black: Negative power 2. Blue: Zone 4 Ground Trigger 1. Green: Warn Away Ground Trigger.

APR/16/2002
6979 USA 5
#H6. 8 PIN BLACK CONNECTOR FOR INPUT CONNECTION:
6. Green Wire: Zone 3 / Negative Door Pin Trigger Input:
4. Blue Wire: Zone 2 / Instant Trigger Ground
7. Violet Wire: Zone 3 / Positive Door Pin Trigger
3. White/Violet Wire: (+) Positive Safety Shut Down Input for Brake switch.
5. White/Green Wire: (-) Diesel Wait-To-Start input
2. Black/White Wire: (-) Neutral Safety Switch Input &
(
-) Remote Start Toggle Switch Input
8. White/Red Wire: Tachometer Signal Input
+12V
1. White/Black Wire: (-) Negative Safety Shut Down Input for Hood pin
IMPORTANT NOTE: Directly connect the BLACK/WHITE wire to the “GROUND” when this wire is not
used.
+12V
#H9. 6 PIN WHITE CONNECTOR FOR OUTPUT CONNECTION
5. White Wire: (-) 200mA Dome Light Control Output
2. Gray Wire: (-) 200mA Trunk (Channel 2) Programmable Output
4. Orange Wire: (-) 500mA Grounded Output When Armed
1. Yellow Wire: (-) 200mA Ignition 3 Control Output
3. Pink Wire: (-) 200mA Programmable Output
2 Steps Door Unlock Output (Factory Default Setting)
orFactorySecurityDisarm SignalOutput
or Start Status (Shock Sensor By-Pass Control) Output
6. Brown/White Wire: (-) 200mA Programmable Output
Horn Output (Factory Default Setting)
orFactorySecurityRearmSignalOutput
WIRING
Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass
through holes on the firewall to prevent fraying. Watches out sharp edges that may damage wires and
causes short circuit.
CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete.
H1: 6 PIN HEAVY GAUGE WIRING CONNECTION:

APR/16/2002
6979 USA 6
Remember that the system does to start a vehicle is duplicate the functions of the ignition key switch! Below,
we will explain the three basic functions of the ignition switch. Since this installation will require analysis of
the ignition switch functions, we recommend making the three connections below at the ignition switch
harness directly.
H1/1. Violet Wire—Starter Output
Careful consideration for the connection of this wire must be made to prevent the vehicle from starting
while in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch
will allow you to properly identify the circuit and select the correct installation method. In addition you will
realize why the connection of the safety wire is required for all mechanical switch configurations.
Failure to make this connection properly can result in personal injury and property damage.
In all installations it is the responsibility of the installing technician to test the remote start unit and assure
that the vehicle can not start via RF control in any gear selection other than park or neutral.
In both mechanical and electrical neutral start switch configurations, the connection of the VIOLET wire
will be made to the low current start solenoid wire of the ignition switch harness. This wire have +12 volts
when the ignition switch is turned to the “START” (CRANK) position only. This wire have 0 volts in all other
ignition switch positions.
NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the
electrical neutral switch configuration, this connection must be made between the starter inhibit relay
(when used) and the neutral safety switch as shown in the following diagram.
Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal
injury and property damage. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.
Start Cut Relay
(When Used)
V
IOLET Wire
Closed in Park or
Neutral Only
Ignition
Switch
“Start”
“On” Neutral Safety
Switch
“Acc”
“Off” Starter
H1/2 & H1/3. Red Wire (2)-- +12V Power Input
Remove the two 20A fuses prior to connecting these wires and do not replace them until the satellite has
been plugged into the control module. These wires are the source of current for all the circuits the relay
satellite will energize. They must be connected to a high current source. Since the factory supplies (+) 12V
to the key switch that is used to operate the motor, it is recommended that these wires be connected
there.
Note: If the factory supplies two separate (+) 12V feeds to the ignition switch, connect one RED wire of the
satellite to each feed at the switch.
H1/4. Yellow Wire – Ignition 1 Output
Connect the YELLOW wire to the ignition 1 wire from the ignition switch. The ignition wire should receive
"12 volts" when the ignition key is in the "ON" or “RUN” and "START" or “CRANK” position. When the
ignition is turned "OFF", the ignition wire should receive "0" voltage.. The YELLOW wire must be
connected.
H1/5. PINK Wire – Ignition 2 Output
Some vehicles have [2] ignition wires that must be power. Connect the PINK wire to the ignition 2 wire
from the ignition switch. The ignition wire should receive "12 volts" when the ignition key is in the "ON" or
“RUN” and "START" or “CRANK” position. When the ignition is turned "OFF", the ignition wire should
receive "0" voltage. If the PINK wire is not used, cap the end of the wire.
H1/6. Brown Wire –Accessory Output (Heater /ACC Output)
Connect the BROWN wire to the accessory wire in the vehicle that powers the climate control system.
An accessory wire will show + 12 volts when the ignition switch is turned to the “ACCESSORY” or “ON”
and “RUN” positions, and will show 0 Volts when the key is turned to the “OFF” and “START” or “CRANK”
position. There will often be more than one accessory wire in the ignition harness. The correct accessory
wire will power the vehicle’s climate control system. Some vehicle may have separate wires for the blower
motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the
second accessory wire.
H2: 5 PIN WIRE HARNESS:
H2/1. RED / WHITE WIRE –PARKING LIGHT RELAY INPUT --

APR/16/2002
6979 USA 7
The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE
wire will determine the output polarity of the flashing parking light relay.
If the vehicle you are working on has +12volt switched parking lights, you don’t need connect this wire.
This wire already connected to +12volt.
If the vehicle’s parking lights are ground switched, cut the RED/WHITE wire, connect the RED/WHITE
wire to chassis ground.
H2/2. WHITE WIRE -- PARKING LIGHT RELAY OUTPUT (+12 V 10A OUTPUT) --
Connect the WHITE wire to the parking light wire coming from the headlight switch. Do not connect the
WHITE wire to the dashboard lighting dimmer switch. (Damage to the dimmer will result). The limitation of
the WHITE wire is 10 AMP max. Do not exceed this limit or damage to the alarm and parking relay will
result.
H2/3. BLACK WIRE -- SYSTEM GROUND –
This is main ground connection of the alarm module. Make this connection to a solid section of the vehicle
frame. Do not connect this wire to any existing ground wires supplied by the factory wire loom, make the
connection to the vehicle's frame directly.
H2/4. BROWN WIRE -- SIREN DRIVE OUTPUT – (See Feature II - 3 Programming)
This is the positive (+) output connection for the siren. Current capacity is 2 amps. Make connection to
the (+) red wire from the siren. Make the (-) black wire coming from the siren to a good chassis ground.
H2/5. RED WIRE -- SYSTEM POWER (+12V CONSTANT) --
The RED wire supplies power to the system. Connect this wire to a constant +12 volt source.
H3. 2 PIN WHITE CONNECTOR FOR THE LED STATUS INDICATOR:
The led indicator status should be mounted in a highly visible area such as top of the dashboard, on top of
the shifter console or on dashboard face. Leave at least 6mm space behind the mounting location for LED
housing. Once a suitable location is chosen, drill a 6mm hole. Run the LED wires through the hole then
press the 2 pin LED housing into the place. Route the LED wires to the control module.
H4. BLACK 3-PIN CONNECTOR. – TWO-WAY TRANSCEIVER/ANTENNA MODULE
The Two-way transceiver/antenna mounts on the windshield (Inside). We suggest you mount it on the
lower left or upper left-hand side of windshield.
Warning! Do not mount in such a manner that it obstructs the driver’s view.
- The Two-way transceiver/antenna whip must be vertical.
- Remove the protective tape backing.
- Carefully align the two-way transceiver/antenna and apply to windshield.
- Route the black connector wire behind the trim and connect to the two-way transceiver/antenna.
- Connect the other end to the control module.
- Special considerations must be made for windshield glass as some newer vehicles utilize a metallic
shielded window glass that will inhibit or restrict RF reception. In these vehicle, route the two way
transceiver/antenna module away from metallic shielded window glass as far as possible.
H5. 3-PIN BROWN CONNECTOR FOR OPTIONAL PAGING (KNOCK) SENSOR
The optional Paging (Knock) Sensor can be add on.
1. Detach the protecting paper from the double-sided adhesive tape and attach one side of the
double-sided adhesive tape to the bottom part of the Paging (Knock) Sensor.
2. After cleansing the area around left bottom part of the front window so that it stays attached firmly, the
Paging Sensor should be attached on the front window so that the side on which a sticker with a printed
words “Tap Here Paging Driver” is attached face outward.
3. Hide the wire by carefully pushing it inside the space of the front window’s mold trim.
4. Adjust the sensitivity of the Paging Sensor, If you turn the tuning screw at the center of the Paging
Sensor clockwise, the sensitivity goes sharp and if turned counter-clockwise, the sensitivity goes dull.
H6: 8 PIN MINI BLACK CONNECTOR :
H6/1. WHITE/BLACK WIRE – NEGATIVE SAFETY SHUT DOWN INPUT --
The WHITE/BLACKE wire provides an instant shutdown for the remote start, whenever it is grounded.
Connect the wire to the hood pin switch previously installed. This wire must be routed though a grommet
in the firewall and connected to the hood pin switch. If the pin switch is to be used with an alarm system,
connect this wire with diode.
Important! This connection is a safety wire and must be connected as shown and tested as specifiled.
Failure to do so may result in personal injury or property damage. See detail of wiring in the following
diagram. This wire may also be used if the vehicle brake light circuit switches ground to the brake lights.

APR/16/2002
6979 USA 8
An isolation diode must be used for ground switched brake light circuits and must be connected to the
output of the brake switch.
To: White/Black Wire /
Negative safety To: Alarm instant trigger Blue wire
Hood Pin Switch
Diode Diode
H6/2. BLACK/WHITE wire —(-)Remote Start Enable Toggle Switch Input —
— (-)Neutral Safety Switch Input —
When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from
ground, the remote start is disable.
1. The optional “remote start toggle switch” can be added on to temporarily disable the Remote Start
Device, it can prevent the vehicle from being remote started accidentally. This feature is useful if the
vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional
remote start enable toggle switch to the OFF position. To enable the remote start, move the optional
remote start enable toggle switch to the ON position.
2. If needed, This wire can connect to the PARK/NEUTRAL switch in the vehicle. (See the TESTING
YOUR INSTALLATION GUIDE)
IMPORTANT NOTE: Directly connect the BLACK/WHITE wire to the “GROUND” when this wire is
not used.
H6/3. WHITE/VIOLET WIRE:– POSITIVE SAFETY SHUT DOWN INPUT
This wire provides an instant shutdown for the remote start, whenever it gets +12volts. If the brake lights
switch in the vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the
brake switch. This will allow the remote start to shut down if an attempt is made to operate the vehicle
without the key while running under the control of the remote start. In most vehicles, in order to shift gear,
the brake pedal must be depressed. The brake input will in turn cause the remote start unit to shut off. See
below diagram.
+12 volts from fuse box
To White/ Violet wire
Brake light bulbs
Switch closes when
brake is depress
H6/4. BLUE WIRE -- GROUND INSTANT TRIGGER INPUT --
This wire is the ground trigger input wire for hood/trunk pin switches.
H6/5. WHITE/GREEN WIRE —(-) DIESEL WAIT – TO - START INPUT –
In diesel vehicles it is necessary to interface with the wire that on the WAIT-TO-START light in the
dashboard. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light
goes out the vehicle can be started. This wire is always at the connector leading to the bulb in the
dashboard. It can also be found at the Engine Control Module (ECM) in many vehicles.
To test and determine the polarity of this wire:
1. Set your multi-meter to DVC or DC voltage (12V or 20V is fine).
2. Attach the (+) probe of the meter to (+) 12V.
3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.
4. Turn the ignition switch to the ON position.
5. If the meter indicates 12 volts until the light goes out you have isolated the connect wire and the wire’s
polarity is negative (ground while the bulb is on).
6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the
connect wire and the wire’s polarity is positive.
Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in
the dashboard. In most diesels the wire is negative (ground turns on the bulb) and this wire can be directly
connected to the wire in the vehicle. If the vehicle use a positive wire (12V to turn the bulb) a relay must be
used to change the polarity.

APR/16/2002
6979 USA 9
(
-
)
Wait To Start Wire
Wait to Start
Indicato
r
Ignition (+)
White/Green Wire
Wait To Start In
p
ut
87a
86
87
30
85
(
+
)
Wait To Start
Wait To Start
Indicator
White/Green Wire
Wait To Start In
p
ut
H6/6. GREEN WIRE -- NEGATIVE DOOR SWITCH SENSING INPUT --
This wire is the ground trigger input wire for negative door pin switch. This wire is connection for
"grounding" type factory door pins locate the "common wire" that connects the door pin switches. Make
the connection of the GREEN Wire here.
H6/7. VIOLET WIRE -- POSITIVE DOOR SWITCH SENSING INPUT--
This wire is the positive trigger input wire for positive door pin switch. This wire is connection for "positive"
type factory door pins(typical FORD MOTOR). Locate the "common wire" for all door pins and make the
connection of the VIOLET Wire here.
H6/8. WHITE/RED wire—Tachometer Signal connection—
Note: You should connect this wire If you program the Start Feature II – 3 to “Tachometer checking
type”,
otherwise not to connect this wire and tap the end.
This input provides the remote start system with information about the engine’s revolutions per minute
(RPM). It can be connected to the negative side of the coil in vehicle with conventional coils. In multi-coil
and high energy ignition system locating a proper signal may be more difficult.
To test for a tachometer wire, a multi-meter capable of test AC voltage must be used. The tachometer wire
will show between 1V and 6V AC at idle, and will increase as engine RPM increases. In multi-coil ignition
system, the system can learn individual coil wire. Individual coil wires in a multi-coil ignition system will
register lower amounts of AC voltage. Also, if necessary, the system can use a fuel injector control wire for
engine speed sensing. Common locations for a tachometer wire are the ignition coil itself, the back of the
gauges, engine computers, and automatic transmission computers.
IMPORTANT! Do not test tachometer wires with a test light or logic probe. The vehicle will be damaged.
How to find a tachometer wire with your multi-meter
1. Set the ACV or AC voltage (12V or 20V is fine.)
2. Attach the (-) probe of the meter to chassis ground.
3. Start and run the vehicle.
4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.
5. If this is the correct wire the meter will read between 1V and 6V.
NOTE: No connection of this wire is required, if you use the voltage or timer checking type mode.
H8. 4 PIN ORANGE CONNECTOR FOR OPTIONAL 2 STAGE SENSOR (ZONE 4)
1. Geen Wire / Warn Away Input
2. Blue Wire / Zone 4 Ground Trigger
3. Black Wire / Negative
4. Red Wire / +12Volts
Function: Allows easy positive, negative, instant trigger, and warn-away trigger connection with quick
disconnect ability for other detection devices.
Connection:
1. Warn away ground trigger = If the sensor or detector connect to this pin, intrude the detector, a
pre-warning tone and light flash warn the intruder to turn back.
2. Zone 4 Ground trigger = With alarm armed, if this pin becomes grounded the alarm Zone 4 will trigger .
3. Negative = When alarm armed this pin become ground.
4. + 12 volts positive = Carry 12 volts all the time. Be sure not to touch ground directly (without a load ), it
might cause short circuit.
H9: 6-PIN MINI WHITE CONNECTOR WIRE HARNESS:
H9/1. YELLOW WIRE:- (-) 200ma IGNITION 3 OUTPUT–
This wire provides a 200mA (-) ground output that becomes active 4 seconds before the remote start unit
initialize, and remains grounded while running.

APR/16/2002
6979 USA 10
Ignition 3 output:
Some newer vehicles use a third ignition wire which is required to start and keep the vehicle’s engine
running. If this is the case, wire an IGN 3 relay (not supplied) as shown below:
Do not connect any vehicle circuits together, they are isolated for a resaon.
Yellow Wire
87a
Ignition 3 Wire From
Ignition Key Switch
+ 12 V Constant Fused
25A Capable
30
8586
87
Transponder interfacing using relay:
If the vehicle has transponder system installed, you will need to by-pass the system while the vehicle is
operating under the control of the Remote Start Unit. To do this:
1.You will need a transponder key that's already programmed to the vehicle.
2.Remove the trim around the ignition switch.
3.Wrap a thin (28 - 30awg) wire tightly around ignition switch 6 to 8 times and secure it.
4.About 6"down line make another loop of approximately 2"diameter.
5.Place the key inside this loop and secure it to the loop.
6. Connect on end of the (28 - 30awg) wire to pin (87) of the relay module.
7. Connect the other end of the loop wire to Pin (30) of relay module.
8. Connect the pin (86) of the relay module to the ignition wire from the ignition switch.
9. connect the pin (85) of the relay module to the H9/1 yellow wire of 6-pin mini white connector.
GM VATS KEY OVERRIDE:
If the vehicle has the General Motor VATS system installed, you will need to by-pass the system while the
vehicle is operating under the control of the Remote Start Unit. To do this:
1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the
key’s value.
2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the ignition
switch to the VATS control module.
3. Connect the YELLOW wire from Remote Start Unit to TERMINAL #85 of an external relay. Connect
terminal #86 of the relay to a fused +12 volt.
4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the
relay. Connect the other side of the (#1) wire to terminal #30.
5. Connect the previously selseced resistor from terminal #87 to the second(#2) wire (as shown).
To + 12 V
Ignition
Switch
YELLOW wire
Matching Resistor
VATS control Module
87a 86
30
87
85
VAT wire (#1)
VAT wire
(
#2
)
H9/2 . GRAY WIRE – (-) 200ma TRUNK (CHANNEL 2) Programmable Output –
This will become a 1 second pulse ground by activate channel 2 on transmitter for two seconds, the
current capacity of this wire is 200 mA. This feature allows you to remote control trunk release or other
electric device. This output can also be programmed to provide the following type of output: momentary,
latched, latched-reset with ignition, 30-second timed. (See Alarm Feature II-6 Programming)

APR/16/2002
6979 USA 11
87a
86
87
30
85
Fuse
Gray Wire
+12V Or Ground
Depending On System
Requirements
+12V
Electric Device
CHANNEL 2
H9/3. Pink wire –(-) 200ma PROGRAMMABLE OUTPUT (See Start Feature I – 5 Programming)
2 STEPS UNLOCK OUTPUT -- (Factory default setting)
The 2 steps unlock feature will work for the most fully electronic door lock circuit. The vehicle must have
an electronic door lock switch (not the lock knob or key switch), which locks and unlocks all of vehicle's
doors. When wired for this feature, press the disarm (or unlock) button one time will disarm the alarm
and unlock the driver's door only. If, press disarm (or unlock) button two times within 3 seconds, the
alarm will disarm and all doors will unlock.
FACTORY SECURITY DISARM SIGNAL OUTPUT –
This wire is designed to disarm a factory installed security system. This wire sends a negative (-) 1
seconds pulse upon a remote start and remote door unlocking. Some factory systems must be disarmed
to allow remote starting. In most cases, this wire may be connected directly to the factory alarm disarm
wire. The correct wire will show nagative ground when the key is used to unlock the doors or trunk. This
wire is usually found in the kick panel area in the wiring harness coming into the car body from the door.
START STATUS (Shock Sensor By-Pass Control) OUTPUT–
This wire is designed to by-pass shock sensor module. This wire will supply an output at all times the
remote start is operating plus an additional 3 seconds after the remote start unit turn off.
H9/4. ORANGE WIRE – (-) 500ma GROUNDED OUTPUT WHEN ARMED --
This wire will become grounded when the alarm is armed. The current capacity of this wire is 500mA. This
output can control starter disable, when an intrusion is detected and the system is triggered. The vehicles
prevent from any unauthorized starting.
87
87a
85
30
86
IN4003 Diode
H9/4: ORANGE wire
from control module
“Start”
“On”
Violet wire
X
Cut
White wire
Oran
g
e wire
“Acc”
“Off”
Starter
H1/1 VIOLET wire (Starter output)
form Heavy Gauge wire harness
Yellow wire to
Ignition Switch
H9/5. WHITE WIRE – (-) 200ma DOME LIGHT CONTROL OUTPUT –
This wire becomes grounded when the dome
light controls circuit active. The current capacity
of this wire is 200mA. This wire can control the
operation of the interior lights. An optional 10
Amps relay can be used to this system for interior
lights operation.
a). Upon disarming, the interior lights will remain
on for 30 seconds.
b). If the vehicle is violated, the interior light will
flash for the same duration as the siren.
87a
86
87
30
85
Fuse
White Wire +12V
Door
Switch
Courtesy
Light
H9/6. Brown/White WIRE –(-) 200ma PROGRAMMABLE OUTPUT (See Start Feature I – 6
Programming)
HORN OUTPUT – (Factory default setting)

APR/16/2002
6979 USA 12
This wire is provided to use the existing vehicle's
horn as the alarm system's optional's warning
audible device. It's a transistorized low current
output, and should only be connected to the low
current ground output from the vehicle's horn
switch. When the system is triggered, the horn
will sound.
8586
87
87a
30
Brown/White
wire
To horn
+ 12 V
+12V Or Ground
Depending On System
Requirements
FUSE
FACTORY SECURITY REARM SIGNAL OUTPUT –
This output is programmable. If programmed rearm a factory installed security system. This wire will
supply a pulse whenever the remote start times out or is shut dowm using the transmitter and remote
door locking..
H10. 3 PIN GREEN CONNECTOR FOR OPTIONAL TEMPERATURE SENSOR.
(See Start Feature I - 7 Programming)
The optional Temperature Sensor can be add on. You can monitor, through the LCD screen, the present
indoor temperature of the passenger compartment before cooling or heating your vehicle.
It also can be programmed to automatically start the vehicle engine whenever the temperature inside the
vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air
temperature every 3 hour and will only start the engine during extreme cold temperatures.
H11. 2 PIN BLUE CONNECTOR FOR THE VALET SWITCH:
Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch
does not have to be concealed, however, concealing the switch is always recommended, as this provides
an even higher level of security to the vehicle. Mount the valet switch in a hidden but accessible location.
Route the valet switch wires to the control module.
H7. 3 PIN DOOR LOCK CONNECTOR:
Blue Wire
Green Wire ( - ) Lock Pulse
( + ) Unlock Pulse
( - ) Unlock Pulse
(
+
)
Lock Pulse
I
INSTALL NEW DOOR LOCK MOTOR
Blue Wire
Green Wire
+12V
3086
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
A
larm
NEGATIVE TRIGGER DOOR LOCK SYSTE
Blue Wire Door Unlock
Green Wire Door Lock
Locking
Master
Switch
To Exiting
Door Lock Relay
POSITIVE TRIGGER DOOR LOCK SYSTEM
Blue Wire Door lock
Green Wire Door Unlock
Locking
Master
Switch
To E x i t i n g
Door Lock Relay
+ 12V

APR/16/2002
6979 USA 13
+12V
Master Door
Lock Switch
X
X
Splice
Splice
Cut the Existing
Lock Wire
To Door
Lock
Motor
To Slave Door
Lock switches
Cut the Existing
Unlock Wire
3 Pin Plug
To Alarm
5-WIRE ALTERNATING DOOR LOCK
30
86
87a
85
87
30
86
87a
85
87
+12V
Green Wire
Blue Wire
VACUUM OPERATED CENTROL LOCKING
Green Wire
Blue Wire
+12V
XCut
Compressor
Door Switch
30
86
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
A
larm
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
5 WIRE ALTERNATING DOOR LOCKS
+12V
Cut the Existing
Lock Wire
Cut Existing Unlock
X
Cut the Unlock Wire
Lock
Unlock
OEM Door Master Lock
OEM Slave
Door Lock
Switch
+12V
LockUnlock
To All Other
Door Lock
Motors
H9/3:
6-Pin
Plug
From
A
larm
Pink Wire
x
X
Blue Wire
OEM Driver’s
Door Lock Motor
+ 12V
+ 12V
85
86 87
87A
30
30
87
85
87A
86
30
87
85
87A
86
Green Wire
H7:
3 Pin
Plug
To
A
larm
VACUUM OPERATED DOOR LOCKING SYSTEM:
TYPICAL OF MERCEDES BENZ AND AUDI.
Locate the wire under the driver's kick panel. Use the
voltmeter connecting to ground, verify that you have t
h
correct wire with the doors unlocked, the voltmeter will
receive "12 volts". Lock the doors and the voltmeter w
i
read "0 volt". Move the alligator clip to +12V and the
voltmeter will receive "12 volts". Cut this wire and mak
e
connections. Be sure to program door lock timer to
3.5 seconds.(See Alarm Feature II – 1 Programming.
)
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
GROUND SWITCHED DOOR LOCKS
Cut Existing Unlock
X
LockUnlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
Pink Wire
OEM
Door Lock
Motor
Existing Neg.
Lock Wire
Existing Neg.
Unlock Wire
86
30
85
87
87A
+ 12V
Green Wire
Door Lock
Blue Wire
Door Unlock OEM Door
Lock Relay
H9/3:
6-Pin
Plug
From
A
larm
H7:
3 Pin
Plug
To
A
larm
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
POSITIVE SWITCHED DOOR LOCKS
Cut Existing Unlock
X
LockUnlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
Pink Wire
OEM Driver's
Door Lock
Motor
+ 12V Existing Pos.
Lock Wire
Existing Pos.
Unlock Wire
30
87A
87
86 85
+12V
+ 12V
OEM Door
Lock Relay
86
30
85
87
87A
Green Wire
Door Unlock
Blue Wire Door Lock
H9/3:
6-Pin
Plug
From
A
larm
H7:
3 Pin
Plug
To
A
larm

APR/16/2002
6979 USA 14
ROGRAMMING
A. PROGRAMMING TRANSMITTER:
PROGRAMMING THE REGULAR REMOTE TRANSMITTER
Important Note: This program mode is for regular remote transmitter and passive/active transmitter
programming only; do not program the TX780V two-way LCD screen transmitter on this mode.
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
Enter:
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You
are now in the Transmitter programming mode.
Program:
1. Press button on one of the transmitter until the siren responds with a confirming chirp the first transmitter
is now programmed.
2. Press button on the second transmitter until the siren responds with a confirming chirp, the second
transmitter is now programmed.
3. Apply the same procedure to program 3rd and 4th.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
∆This system has an unique optional TX040 passive/active transmitter design, it’s programming is
the same as above. (To see how it works, please see operation part.)
PROGRAMMING THE TX780V TWO-WAY LCD SCREEN REMOTE TRANSMITTER
Important Note: This program mode is for TX780V two-way LCD screen transmitter programming only; do
not program other style transmitter on this mode.
Note: This mode will only retain the last 2 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
The two-way LCD screen remote transmitter can be add on for this system. The two-way remote transmitter
actively gives an immediate report to the remote transmitter on any violations occurred to your vehicle both
by visual graphic icon and audio sound.
When you press a button of two-way remote transmitter, you can make sure if your command has been
correctly delivered to the system module in your vehicle, The displayed graphic icon on the LCD screen as
well as by hearing a confirming melody sound from your two-way remote transmitter.
Enter:
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 6 times and hold it until a long chirp is hearing then release the valet switch. You
are now in the two-way LCD screen remote Transmitter programming mode.
Program:
1. Press Button on one of the transmitter until the siren responds with a confirming chirp the first transmitter
is now programmed.
2. Press Button on the second transmitter until the siren responds with a confirming chirp the second
transmitter is now programmed.
Note: Maximum (2) two-way LCD screen remote transmitter can be program.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
IMPORTANT NOTE: This program mode is for TX780V two-way LCD screen transmitter programming
only; do not program other style transmitter on this mode.

APR/16/2002
6979 USA 15
TX780V TWO-WAY LCD SCREEN REMOTE TRANSMITTER
B. FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2times and hold it until one chirp with a long chirp is hearing then release the valet
switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a. The siren chirps and LED pause will indicate previously setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the transmitter
button ‘A’ again until the module advances to your desired setting.
a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps.
b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
For example: To program the arming mode form “Active arming” to “Passive Arming without Passive Door
Locking”, After “Arming mode” program, the next program is “Rearm on/off” .……….
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 2 times and hold it until a chirp with a long chirp is hearing then release the valet
switch.
3 Press and release the transmitter button corresponding to the feature ‘Arming mode’ you wants to
program. [1] LED flash, [1] chirp to indicate your are in features “Active Arming”.
4 Depress the transmitter button twice to change the feature. [3] LED flash, [3] chirps to indicate your
are in features “Passive Arming without Passive Door Locking ”.
5 Depress the transmitter button corresponding to the features ”Rearm on/off”’ you want to
program……..
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1 All chirps on Siren chirp on only Horn chirp on only All chirps off
2 Active arming Active arming with
Passive starter
disable
Passive arming
without passive door
locking
Passive arming with
passive door
locking.
3 Automatic Rearm on Automatic Rearm off
4 With Door Ajar error
chirp
Bypass Door Ajar
error chirp.
5 Without Car-jack
mode
Active Car-jack
mode
Passive Car-jack
mode
6
Transmitter can not
Arm the System
When Driving
Transmitter can be
Arming the System
When Driving
7 Panic with Ignition
off
Panic with Ignition
on & off
Panic with Ignition
on & off. Panic with
No time limit.
Without Panic
function.

APR/16/2002
6979 USA 16
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Door Ajar Error Chirp on/off:
This feature controls the error chirp that is generated if the system is armed with the door trigger active. This
useful in vehicles that has a long dome light delay after the door has been closed. If the system is armed
before the dome light has turned off, the security system will generate the door trigger error chirp. If this error
chirp is not desired, use this feature to disable the door open error chirp. If the bypass chirp is turn off, no
bypass chirp will be generated, ever if a door is accidentally left open.
Active Arming With Passive Starter Disables: The “Ground-when-armed output will go active 60 seconds
after the ignition is turn off. The LED will flash at half its normal rate when the ignition is turn off to indicate
that the system will interrupt the starter in 60 seconds.
Transmitter Can Be Arming The System When Drive: Press and hold the button on the transmitter for
2 seconds while the ignition is “ON”. The system will be arm and the system will not respond to any trigger
input except the door triggers and starter disable relay (if installed) will no be activated.
ALARM FEATURE “II” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 4times and hold it until two chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp / LED one
pulse
Factory Default
Setting
Two Chirps / LED
two pulse
Three Chirps / LED
three pulse
Four Chirps / LED
four pulse
1 0.8-second Door
lock pulses.
3.5-second Door
lock pulse.
Double pulse unlock
2 Ignition controlled
door locks & unlocks
Ignition controlled
door locks only
Ignition controlled
door unlocks only
Without ignition
controlled door locks
& unlocks
3 H2/4 Brown Wire =
Constant Siren
output for 6-tone
siren
H2/4 Brown Wire =
5-second pulse Siren
output for signal tone
siren
H2/4 Brown Wire =
Random pulse Siren
output
H2/4 Brown Wire =
Horn Output
4 Pathway illumination
feature “off”
Parking light “on” for
30- second upon an
unlock signal
Parking light “on” for
30- second upon an
unlock signal &
10-second upon a
lock signal.
5 With code “hopping” Without code”
hopping”
6 H9/2 Gray Wire
Channel 2 Output =
1 second pulse
output for trunk
release.
H9/2 Gray Wire
Channel 2 Output =
Momentary output
H9/2 Gray Wire Channel 2 Output = Latched
(3) / Latch output and reset with ignition “on”
(4) / 30-second timer output (5) / 60-second
timer output (6)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Momentary output = The momentary output selection will output a negative signal from the Channel 2
output immediately when the channel 2 button is pressed and will continue until the button is release.
Latched output = The latched output selection will output a negative signal as soon as the Channel 2 button
is pressed and will continue until the button is pressed again.
Latched output / reset with ignition = The latched / reset with ignition output selection operates just like
the latched output but will reset or stop when the ignition is turned on.

APR/16/2002
6979 USA 17
ALARM FEATURE “III” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1 Exit the programming mode. (3 long chirp to confirm this exit.)
2 Exit the programming mode. (3 long chirp to confirm this exit.)
3 Press & hold button
3 for 4 seconds to
delete the sensor
code
Wireless
door/window sensor
& PIR sensor
programming mode
4 Override Without
Password Pin Code /
Press & hold button
4 for 4 seconds to
delete the Password
pin code
Override With
Password Pin Code /
Password pin code
programming
5 “TEST” Mode for
Zone 2 / instant
trigger &
Zone 3 / Door trigger
“TEST” Mode for
Zone 4 / the Optional
Sensor connected to
4 pin plug.
“TEST” Mode for
Zone 5 / Wireless
door/window sensor
& PIR sensor
6
Adjusting and Testing Zone 1 / Built-in Shock Sensor. Press button will decrease
sensitivity by one.
7 Adjusting and Testing Zone 1 / Built-in Shock Sensor. Press button will increase
sensitivity by one.
Exit: Turn Ignition to 'ON' position / leave it for 15 seconds / press button or . A 3 long chirps & 3
parking light flashes to confirm exit 1-4
Program The Wireless PIR Sensor or Wireless Door/Window Sensor.
This system has a very unique interfacing with optional sensor, to extend more protection, such as PIR
(IR-70S) sensor or Door/Window sensor. (DS-70S)
For example, in your garage you can put a PIR for protection. (A device to detect person's movement in a
protected area.) If system armed, a person walk through the detect area, the siren inside the car will
alarming to raise the attention to the owner.
So the same thing applies in door/window sensor, (A device to detect door/window open.) you may put the
sensor to the garage door or window. If system armed, a person opens the door or window, the siren will
alarm.
Set the PIR and door/window sensor the same code if you use both of them.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
Program:
1. Press and release the transmitter button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Sensor Programming mode”.
2. Activate the sensor to let the system program it's code. [2] Chirps to confirm programmed. (Only one code
could be program)
Delete:
Within 15 seconds, Again press and hold the transmitter button for 4 seconds. A [1] long chirps to

APR/16/2002
6979 USA 18
confirm deleted the sensor code.
Password Pin Code Setup:
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode. You can program or delete the
password pin code as below:
Program:
1. Press and release the transmitter button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Password Pin Code Programming mode”.
2. Within 5 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet Switch
from 1 – 9 times.
3. Within 15 seconds of the last entered 9ths digit, turn the Ignition switch to “ON” position.
4. Within 15 seconds, enter your chosen second 9ths digit by pressing and releasing the valet Switch from
1 – 9 times.
5. Finish by turning the ignition switch to “OFF” position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause and then the second digit code. The unit
will report the new code three times with a one-second’s pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
Within 15 seconds, press and hold the transmitter button for 4 seconds. A one long chirps to confirm
Deleted the Password Pin Code.
Example: To program the Password Code 92, you would;
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
Program:
1. Press and release the transmitter button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Password pin code programming mode”.
2. Within 5 seconds, press and release the valet Switch 9 times.
3. Within 15 seconds of the last entered 9ths digit, Turn the Ignition Switch to “ON” position.
4. Within 15 seconds press the valet Switch twice.
5. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
Test Mode
In this test mode, this system can test the Zone 2 / Instant ground trigger, the Zone 3 / Door trigger, and the
Zone 4 / optional sensor sensitivity. The installer can save time to test the optional sensor sensitivity and
sensor without using the traditional arming/disarming procedures to test the sensors.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
4-a. Test the Zone 2 / Instant Ground Trigger & Zone 3 / Door Trigger:
Press and release the transmitter button once. [1] LED flash, [1] siren/horn chirp to indicate your are
in
Zone 2 / instant ground trigger and Zone 3 / Door trigger test mode.
Trigger sensor Siren chirps
Zone 2 / Instant Ground trigger (H6/4 Blue wire) 2
Zone 3 / Door trigger (H6/6 Green or H6/7 Violet wire) 3
4-b. Test the Zone 4 / Optional Sensor (Connected to H8 4 Pin Plug):
Press and release the transmitter button again. [2] LED flash, [2] siren/horn chirps to indicate your
are in optional sensor (connected to H8 4 pin plug) test mode.

APR/16/2002
6979 USA 19
1. Activate the warn-away (first stage optional sensor), system will emit a short chirp.
2. Activate the full alarm (second stage optional sensor), system will emit a long chirp.
3. Continue to test the optional sensor until reach the proper sensitivity.
4-c. Test the Zone 5 / Wireless PIR or Door Switch:
Press and release the transmitter button again. [3] LED flash, [3] siren/horn chirps to indicate your
are in optional wireless PIR or Door switch test mode.
Trigger sensor Siren chirps
Zone 5 / Optional wireless PIR or Door Switch 5
Adjusting and Testing The On-Board Shock Sensor (Zone 1).
The Zone 1 / shock sensor has been built in this system, you can use this mode to test and adjust sensitivity
of the shock sensor. The installer can save time to adjust and test sensitivity of the shock sensor without
using the traditional arming/disarming procedures.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
Adjusting and Testing:
There are 16 steps of adjustment for the shock sensor.
1. Press the transmitter button once will decrease sensitivity by one, each time an decrease is made
the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the minimum of sensitivity.
2. Press the transmitter button once will increase sensitivity by one, each time an increase is made the
siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the maximum of sensitivity.
3. Back the factory default setting: Press and hold the transmitter or button for 4 seconds until A (1)
long chirp from siren/horn, The sensitivity of the shock sensor will Back the factory default setting.
4. To test the shock sensor sensitivity adjustments, apply a shock to the vehicle.
a. Activate the warn-away (first stage shock sensor), system will emit a short chirp.
b. Activate the full alarm (second stage shock sensor), system will emit a long chirp.
5. Continue to test the shock sensor until reach the proper sensitivity.
REMOTE START FEATURE PROGRAM MODE.
START FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 8times and hold it until four chirps with a long chirp is hearing then release the
valet switch. You are now in the Start feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1 10 minutes run time 20 minutes run time 30 minutes run time 5 minutes run time
2 Factory alarm disarm
with channel 2 on
Without this feature
3 Constant parking
light output
Flashing parking
light output
4 Door lock before
start
Without this feature
5 H9/3 Pink Wire =
Two step door
unlock output
H9/3 Pink Wire =
Factory Security
Disarm Signal
Output
H9/3 Pink Wire =
Start Status (Shock
Sensor Bypass
Control) Output
6H9/6 Brown/White
Wire = (-) 200ma
Horn Output
H9/6 Brown/White
Wire = Factory
Security Rearm
Signal Output

APR/16/2002
6979 USA 20
7 Temperature-Control
Starting OFF
Temperature-Control
Starting 5 F (- 15 C)
Temperature-Control
Starting - 7 F (- 20
C)
Temperature-Control
Starting - 22 F (- 30
C)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
START FEATURE “II” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing then release the
valet switch. You are now in the Start feature ‘II’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1 Exit the programming mode. (3 long chirp to confirm this exit.)
2 Exit the programming mode. (3 long chirp to confirm this exit.)
3 Tachometer
checking type.
Voltage checking
type
Timer checking type
RPM learning
4 Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10 chirps),
5 Start the system for TESTING & ADJUSTMENT
6Hi check level Low check level
7Stop the remote start system for TESTING & ADJUSTMENT
Exit: Press the or button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
T
ACHOMETER CHECKING TYPE
Enter Start Feature ‘II’ Programming Mode:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing then release the
valet switch. You are now in the Start feature ‘II’ programming mode.
Select “Checking Type”:
3. Press and release the transmitter button once to set the “Tachometer Checking Type”. [1] LED flash,
[1] chirp to Confirm this setting.
4. Once you complete step 3, you can program “RPM Learning Mode” as below:
RPM Learning
While the system stay in Start Feature “II” programming mode,
1. Press and release the transmitter button once, [1] chirp to indicate your are in features “RPM
Learning mode”.
2. Start the vehicle with the key. (While the engine is running, the parking & LED will flash, If don’t, please
check tachometer White/Red wire connection. (H6/8)
3. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two seconds.
The RPM signal is learned.
4. Once you complete step 3, turn off the ignition switch to stop the engine then you can adjust and test
“Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
While the system stay in Start Feature “II” programming mode,
1. Press the button on the transmitter to start the vehicle.
2. If everything goes well: