Commercial Electric Heat RDH 6000 User manual

Installation Instructions
Complete with REMOTE SWITCH UNIT
for Fan only, 3kW and 6kW
RDH 6000
Recessed Over Door
Heater
Please retain for future reference
Reference
J289f
Commercial Electric Heat Limited
Burnfoot Industrial Estate
HAWICK
Roxburghshire
TD9 8SL
Tel [phone] Fax [phone]
Email [email protected] Web www.cehltd.co.uk

LOCATION
The heater must be installed at least 2.0m above floor
level. All round minimum clearance dimensions must be
observed.
For optimum effect the heater should be mounted as close
as possible to the top of the doorway. The maximum
recommended mounting height is 2.3m for 3kW and 2.8m
for 4.5, 6.0 and 9.0kW units.
The heater is designed to take input air from the
ceiling void it is therefore imperative that a suitably
sized inlet grille is provided within the ceiling or
enclosure.
The heater must not be covered or the airflow impeded
in any way.
If one inlet grille is at its minimum dimension the other
must have an unrestricted airflow
CONTROL
Remote Switch
Thermostat (CRST16 or CPRST)
The Remote Switch Unit allows ON/OFF, Fan only with 3kW and 6kW.
This will switch the heater off when set temperature is
reached. To allow the fan only to operate in summer the thermostat must be set high and the heat switches
must be in the off position.
If a thermostat is required remove link between Fuse and Lt and replace with connection to thermostat. A
thermostat with at least a 3A rating is required.
The control circuit is fitted with a 3A fuse should this blow check for reason and replace , if the problem
persists consult a suitably qualified person.
CONTENTS
- grille frame and 2 no roundhead woodscrews
Remove from carton and check contents ;
- heater unit
- 2 no support brackets, 4 no. machine screws and 4 no woodscrews
- ODH-RSW three switch control unit
- 25mm cord grip bush and locknut
ELECTRICAL CONNECTION
The heater should be installed in accordance with the latest edition of the IEE Requirements for Electrical
Installation (BS 7671:2008)
The unit should be permanently connected to a suitable 230Vac power supply incorporating a means of
isolation having a contact separation of at least 3mm in all poles.
remote switch unit in suitable location.
Select cabling with 4 cores and earth and of appropriate size for current and volt drop.
Pass cable/s through cord grip in back of unit. Leave sufficient length for connection but ensuring cables do
not foul blower unit. Make off connections to connector block and earth stud in accordance with circuit
diagram RDH-W-003 (copy on back page )
If remote switching is not required connect power supply to L and N and link Lt,Lsw,LI and LII with 1.5sqmm
cable.
Tighten up cord grip. Replace cover.
Remove heater cover, position heater in ceiling (See Fixing). Fix
Note: Ensure link between Fuse and Lt is secure otherwise heater will not operate
WARNING THE HEATER MUST BE EARTHED
IMPORTANT : always check to ensure the heating elements cannot be energised without the fan
running.
OVER TEMPERATURE CUT OUT
To RESET -
Should the heater exceed normal operating temperature the over temperature cut out on the heating
elements will operate switching off both elements and fans.
switch off power to the unit and allow to cool before switching on again. If the problem
persists consult a suitably qualified person.
min
20
min
100
min
30
SAFETY
The correct procedures for working at height must be adopted when installing this heater.
The heater must be installed by a suitably qualified person in accordance with current regulations.

FIXING
Fitting in plasterboard type ceiling or bulkhead
The unit can be fixed in two ways depending on access available (Note future access will be required for
servicing) .
1) Locate
2) Locate the brackets to sit on top of the support frame (see Fig 2).Position the grille frame in the opening
and loosely fix with the 2 round headed screws provided. Place unit in ceiling from above and position within
grille frame. Secure brackets with woodscrews provided, tighten grille frame fixing screws.
The heater can be fitted in a modular ceiling but drop ro fixing (see below) will be required. The ceiling tile is
cut back as appropriate and finished either with the grille frame or additional T bar section.
Additional fixings may be required if the ceiling construction is not strong enough to take the heater weight.
Two 8mm holes are provided in the top of the heater to allow the fixing of drop rods (by others).
(see Fig 1). Ensure sufficient space is left to allow the insertion of the grille frame
between heater and bracket. This option may require electrical connection prior to positioning..T
frame
Fitting in modular ceiling.
Drop rod fixing
This unit is designed for installation in a plasterboard or similar ceiling where a free height above the surface
of the ceiling is at least 230mm.
A 810mm x 130mm hole should be made in the ceiling and suitably framed.
Fix support brackets, with machine screws provided to screwed inserts in side of unit
the brackets flush with the front of the heater. Place unit in ceiling from below and secure brackets
with woodscrews provided.
he grille
is then positioned and fixed with the 2 round headed screws provided.
The manufacturers reserve the right to change the specification at any time without prior notice EO&E
MAINTENANCE
Isolate the heater and remove any build up of dust etc. every 6 months. Check that the heater has not been
covered or the airflow restricted in any way.
Fig 1 Fig 2
WARRANTY
This product is guaranteed, in accordance with our Conditions of Sale, for a period of 12 months from date of
purchase. We will repair or replace, at our discretion, any part found to be defective. We cannot accept
responsibility for any consequential liability.
The warranty will be invalid if the heater has not been installed in accordance with these instructions.

F U S E
6
L LL1 L11
If required remove link and replace with thermostat Commercial Electric Heat Limited
HAWICK TD9 8SL
No Part No Description
No DateRevision
Title
RevDrawing No.
Date
Drawn by
Scale
L011
Lt
Lsw
I
II
Relay II
O T cut out
Relay ILN
RDH-W-003 2nts
NEB 06.09.00
Fan Motor
Heating Element
Fan Motor
Heating Element
1 2 3 4
B078-01 D001-01 F040 C014
ODH-RSW
Heating element Fan motor Connector block Blower unit
Remote switch unit
5
6
8
7
1 2
08/04
08/07
E113
F057
E127
Add external cut outs/tstat
Add control fuse
Relay
Fused conn block
3A QB Fuse
O T cut out
Connector Block
38
77
6
22
1
1
All wiring in 105 C Trirated Panel wire
0
To reset over temperature cut out(s) Switch off, check for cause of overheating and rectify, allow to cool (5 minutes) then restore supply Heater does not function again until power has been removed from cut out.
RDH-6000 6.0kW
Recessed Over Door
Heater
Schematic diagram
1.5kW each
22
L
N
IMPORTANT: Any modification to the switching in this circuit must ensure that the heating elements cannot be energised without the fan running. Remote Switch ODH-RSW
P08