Compaq 1825 User manual

b
User’s Guide
1825 Flat Panel Monitor
Document Part Number: 305222-001
August 2002
Sarah User Guide.book Page i Tuesday, September 3, 2002 8:33 AM

© 2002 Compaq Information Technologies, L.P.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq Computer Corporation shall not be liable for technical or editorial
errors or omissions contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this
material. The information in this document is provided “as is” without
warranty of any kind, including, but not limited to, the implied warranties
of merchantability and fitness for a particular purpose, and is subject to
change without notice. The warranties for Compaq products are set forth in
the express limited warranty statements accompanying such products.
Nothing herein should be construed as constituting an additional warranty.
This document contains proprietary information that is protected by
copyright. No part of this document may be photocopied, reproduced, or
translated to another language without the prior written consent of Compaq
Computer Corporation.
ÅWARNING: Text set off in this manner indicates that failure to
follow directions could result in bodily harm or loss of life.
ÄCAUTION: Text set off in this manner indicates that failure to follow
directions could result in damage to equipment or loss of information.
User’s Guide
1825 Flat Panel Monitor
First Edition August 2002
Document Part Number: 305222-001
Sarah User Guide.book Page ii Tuesday, September 3, 2002 8:33 AM

User’s Guide 1
1825 flat Panel Monitor
Product Features
The 1825 Flat Panel Display has an active matrix, thin-film
transistor (TFT), liquid crystal display (LCD). The monitor
features include:
■Large 18.1-inch (45.9 cm) viewable area display.
■1280 × 1024 native resolution, plus full-screen support for
lower resolutions.
■Wide viewing angle to allow viewing from a sitting or
standing position, or moving side-to-side.
■Tilt and swivel adjustment capabilities.
■Removable base for flexible mounting solutions.
■Multiple video inputs supported:
❏VGA Analog
❏DVI-I supports either Analog or Digital signal input
■VGA analog and DVI-Digital signal cables included.
■Plug and play capability if supported by your system.
■On-Screen Display (OSD) adjustments in English, French,
German, Italian, Spanish, and Simplified Chinese for ease of
set-up and screen optimization.
Sarah User Guide.book Page 1 Tuesday, September 3, 2002 8:33 AM

2User’sGuide
1825 flat Panel Monitor
■Software and Reference Library CD includes an information
file (INF), Image Color Matching file (ICM), and product
documentation.
■Energy Saver feature for Energy Star compliance.
■AssetControl
■Compliant with the following regulated specifications:
❏EPA ENERGY STAR
❏European Union CE Directives
❏Swedish MPR II 1990
❏Swedish TCO '99
Installing the Information Files
The CD-ROM included with this monitor contains two
information files to be installed onto your computer; an .INF file
and an .ICM file.
■The .INF file defines monitor resources and provides
specifications used by most operating systems to install
support software for certain hardware devices. The .INF file
ensures monitor compatibility and optimization with your
computer’s graphics adapter. INF files are downloadable by
clicking on: www.hp.com/go/support and selecting the desired
monitor.
■The .ICM file provides color matching consistency from
monitor screen to printer and is activated from within
graphics programs that have this feature.
To install these files on your computer, insert the Software and
Reference Library CD in your computer CD-ROM drive. When
the CD menu launches, select Install INF and ICM Files and
follow the on-screen instructions.
Sarah User Guide.book Page 2 Tuesday, September 3, 2002 8:33 AM

1825 flat Panel Monitor
User’s Guide 3
Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the
monitor, computer system, and other attached devices, then
follow these steps:
1. Place the monitor in a convenient, well-ventilated location
near your computer.
2. Connect the monitor signal cable to the video connector on
the rear panel of the computer.
✎The DVI-D cable supplied with this monitor is for
digital-to-digital connection only. Your computer must have a
DVI-compatible graphics card installed for use with this cable.
When connecting the DVI-D signal cable to the DVI connector
on the monitor, you must connect the other end of the DVI-D
cable to the DVI connector on the computer.
3. Connect the monitor signal cable to the back of the monitor.
4. Connect the power cable to the back of the monitor.
5. Connect the power cable to an electrical wall outlet.
Sarah User Guide.book Page 3 Tuesday, September 3, 2002 8:33 AM

4User’sGuide
1825 flat Panel Monitor
6. Adjust the monitor as needed for your comfort using the
monitor’s tilt, swivel, and height adjustment capabilities.
✎You can change your monitor’s viewing position to portrait. To
rotate your display to the portrait position, you will need to install
the Pivot software, which is contained on the CD included with
your monitor.
Sarah User Guide.book Page 4 Tuesday, September 3, 2002 8:33 AM

1825 flat Panel Monitor
User’s Guide 5
Sarah User Guide.book Page 5 Tuesday, September 3, 2002 8:33 AM

6User’sGuide
1825 flat Panel Monitor
ÅWARNING: To reduce the risk of electric shock or damage to your
equipment: Do not disable the power cord grounding plug. The
grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) electrical outlet that is
easily accessible at all times.
Disconnect power from the monitor by unplugging the power cord
from the electrical outlet.
Do not place anything on power cords or cables. Arrange them so
that no one may accidentally step on or trip over them. Do not pull on
a cord or cable. When unplugging from the electrical outlet, grasp
the cord by the plug.
ÄCAUTION: Burn-in image damage may occur on monitors that
display the same static image on screen for a prolonged period of
time. To avoid burn-in image damage on your monitor screen, you
should always activate a screen saver application or turn off the
monitor when it is not in use for a prolonged period of time.
Selecting the Signal Connectors and Cables
There are two signal input connectors: one VGA connector and
one DVI-I connector. The monitor will automatically determine
which inputs have valid video signals. The inputs can be selected
via the On-Screen Display (OSD) feature or by pressing the
Signal Input Selection control on the monitor front bezel.
The video mode supported by the DVI-I connector is
determined by the video cable used. For digital operation, use
the DVI-D to DVI-D signal cable provided. For analog operation,
a DVI-I to VGA signal cable must be attached to the DVI-I input
(not provided with the monitor).
Sarah User Guide.book Page 6 Tuesday, September 3, 2002 8:33 AM

1825 flat Panel Monitor
User’s Guide 7
Removing the Monitor Base
You can remove the monitor base to mount the monitor on a wall,
a swing arm or other mounting fixture. To remove the monitor
from the base, read the caution and warning below before
beginning the procedure.
ÄCAUTION: Before beginning to disassemble the monitor, be sure
the monitor is turned off and the power and signal cables are both
disconnected.
Lay the front bezel down on a soft area to prevent it from getting
scratched, defaced, or broken
ÅWARNING: Do not remove the base from the monitor while the
monitor is in the upright position. Before removing the monitor from
the base, ensure that the monitor is lying flat, front bezel down, and
that the base is set to the maximum base extension. Attempting to
remove the monitor from the base while upright in the minimum base
extension may result in injury to the user.
1. Disconnect and remove the signal and power cables from the
back of the monitor.
Sarah User Guide.book Page 7 Tuesday, September 3, 2002 8:33 AM

8User’sGuide
1825 flat Panel Monitor
2. Remove the four screws as shown in the following
illustration.
ÄCAUTION: Ensure that the bottom of the monitor base is positioned
over a table or desktop before removing the base from the monitor.
3. Remove the monitor base from the monitor.
Mounting the Monitor
1. Remove the monitor base. Refer to “Removing the Monitor
Base” steps in the previous section.
When the base is removed, four threaded mounting holes are
exposed on the monitor panel to be used for mounting purposes.
These mounting holes are spaced 100 mm apart and are
compliant with the Video Electronics Standards Association
(VESA) standard for mounting flat panel displays.
Sarah User Guide.book Page 8 Tuesday, September 3, 2002 8:33 AM