Competition DH16A-11DT User manual

Access control
instruction manual
*Anti-vandal *metal surface*pickproof *waterproof
Fashion
Technology
Security
Unique
We will remain the right of modification without prior information

DH16A-11DT
NO. Description
①
②
③
Infrared area
Keyboard
①
②
③
Antenna
Specifications/features
1.With internal EM reader
2.Frequency:125KHZ
3.Effective distance:5-10cm.
4.Up to 2000 card holders.
5.Infrared keypad operation.
6.Built-in anti-tamper function.
7.Watchdog timer, powerful reboot and self-recovery watchdog
can connect with the external unlock button .
8.Power consumption: DC 12-15V, Current:150mA
9.Unlock output delay time:0~99s.
10.IP Rating:65
11.Single relay outputs.
12.relay current: 2A/12VDC
13.Dimension:115*75*21mm
front panel description
B B
B B
Before installing ,position the location where the controller
unit is to be mounted , operation according to the following steps:
1.Open the controller by loosening and
removing the back case screw at the
bottom using the spline tool .
2.Drill the respective holes in the rear cover
for flush mount ,drill the four holes marked
B .
3.Use the provided drilling template accurately
locate and drill the required holes.
“ ”
installation
4.Use the screws provided to mount the back
case on the wall ,be sure to draw the wiring through the large
centre hole in back case, and Keep it level.
5.Connected accurately the system wiring as per the label enclos ed
on the rear.
6.Replace the unit back and screwed it on using the spline tool.
Screw anchors
System wiring
Screws
1 2
ed

Enter the system
Press the * and # button on the access control keyboard, follow the
4-digit primary password , and then press the # button, the indicator
will flash red , a long tone Di will be heard, now enter setting
mode.(note:The primary password is 4567.)
“ ”
Add user card
Enter the setting mode: Press the button 1 in the mean time a
tone Di will be heard, take
two tone
Di indicates the user card success of user card adding . add other
magnetic cards one by one with a continuous tone Di . With 4
tones Di indicates this card has already been added . After all
user cards setting are completed, press the button * to return to the
setting mode, follow the button * to return to the standby mode.
“ ”
“ ”
“ ”
“ ”
“ ”
a magnetic card near the sensor of
Access Control or input the last 6-digital card number .
Note : the system is automatically quitted in 20 seconds of inactivity.
Note:Record the series numbers of these user cards.
Note:
1.all operations can be fulfilled via this wireless keyboard.
2.take the antenna of keyboard vertically aimed at the infrared
area in order to good data transmitting.
Delete user card
Enter the setting mode: Press the button 2 in the mean time a
tone Di will be heard, take
wo tone
Di indicates the success of user card deleting .Delete other user
cards one by one with a continuous voice Di . The 4 tones Di
indicates this card has already been deleted . After all user cards
deleting are completed, press the button * to return to the setting
mode, follow the button * to return to the standby mode.
“ ”
“ ”
“ ”
“ ” “ ”
a magnetic card near the sensor of
Access Control or input the last 6-digital card number. T
Delete all cards
Enter the setting mode. Press the button 9 in the mean time a
tone Di will be heard, follow the button 9 again. then
hearing a continuous tone Di , the tone disappearance indicates
the all user cards are deleted. press the button * to return to
the setting mode, follow the button * to return to the standby mode.
“ ”
“ ” “ ”
“ ”
Change the administration password
Enter the setting mode. Press the button 8 in the mean time
a tone Di will be heard, input the 4-digit new password , then
press the # button. When hearing a tone Di , repeat the new
password and the button # to confirm in the mean time two tones
DiDi will be heard,. If the continuously voice are heard, repeat
again this operation as above till the two tones DiDi is heard.
“ ”
“ ”
“ ”
“ ”
“ ”
Operation
3 4
ed

Enter the setting mode. Press the button 4 in the mean time
a tone Di will be heard ,input the unlocking delay time (01to 99
are available),press the button * to return to the setting mode,
follow the button * to return to the standby mode.
“ ”
“ ”
set the delay time for door unlocking
Enter the setting mode. Press the button 3 in the mean time
a tone Di will be heard ,input the building number (XXXX) and
entrance number(XX),press the button # to confirm. press the button
* to return to the setting mode, follow the button * to return to the
standby mode.
“ ”
“ ”
Set the building and entrance
Wring diagram
Red -power + DC12-15V
Black -power GND
Brown -unlocking button
Orange- NC
Yellow- COM
Green- NO
Gray- 485+
White- 485-
Red
Black Power supply
+
-
Brown
Orange
Yellow
Green
unlocking button
DC/AC
power
adapter
Door lock
NO
NC
5 6
ed