Component Solution Services Verity REC02C User manual

7 INCH
Quad DVR 32 Gig SD Card
REC02C
Please read this manual completely before operating the SYSTEM
A division of
Component Solution Services, LLC.
56600 Twin Branch Drive
Mishawaka, IN 46545
2018 Verity Rear Vision Systems / All rights reserved / Subject to Change

Think Safety
First
Read our manual before operating
or installing.
Most likely, your system came preinstalled so the installation
section would be for reference.
Thank you for your purchase of our Verity Rear Vision
Systems®. When installed and used properly, your
REC02C is designed to deliver you years of trouble-free
operation. This manual contains important information
required to properly install and operate the unit. Verity Rear
Vision Systems are designed for quick installation by trained
professionals in proper installation environments. Our
designs are based on decades of working with vehicle
manufacturers.
Verity Rear Vision Systems products are intended to be
installed as a supplement and our observation systems
and/or products are not intended for use as substitutes for
rear-view mirror devices, or for any other standard motor
vehicle equipment which may be required to be installed on
vehicles by law. Verity Rear Vision Systems products
promote improving the vehicle operator’s field of view. Our
products are no substitute for proper defensive driving
techniques, observance of traffic laws and motor vehicle
safety regulations.
Installation Location
It is unlawful in most locals for any person to drive a motor
vehicle equipped with a television viewer/screen located at
any point forward of the back of the driver’s seat (or in any
location that is visible, directly or indirectly), to the driver
while operating the vehicle. Our systems are designed to be
used primarily as a rear observation device.
DO NOT OPEN ANY COMPONENT. There are no
serviceable parts inside any of the components of the Verity
Rear Vision products. Opening the product will break the
tamper indicators and void the warranty. Contact our tech
support if a problem should arise 574-807-6002. For faster
response, fill out a service ticket found on our website tech
support section. www.verityrvs.com

WARNING
Do not place heavy objects on cables or
cover them with carpet or mats.
Do not place cables where they can be
crushed in any manner.
Our systems are designed as a driving aid.
Watching videos, broadcasts, DVDs and/or
any images other than intended driving
assistance cameras is prohibited.
CAUTION
To avoid damage to the electronic circuit,
stop using this product while doing welding
work to the vehicle and/or trailers.
Never immerse any component in water, and
do not employ spray cleaners. When
cleaning, use a damp lint-free cloth only.
Connect this unit only to other compatible
devices.
Although our products have built-in surge
and cross polarity protection, make sure all
cables are connected properly; improper
cable connections may damage the camera
and the monitor.
Cables should not be allowed to touch hot or
rotating parts, such as the engine, ventilator,
etc.
Do not locate the monitor near heat
generating vents or devices.
Turn off power to the monitor when
connecting the camera.
Monitors are not designed to be waterproof. (Our
SM07F waterproof monitor is the exception.)
Exposure to water, such as rain, may damage the
unit.

KEY STROKE INSTRUCTIONS
REMOTE INSTRUCTIONS

KEYSTROKE INSTRUCTIONS
Press Menu: Press the (+) key to advance to the next
menu screens. Menu Screens are PICTURE, VOLUME,
OPTION, SYSTEM.
Screen 1: Depress menu repeatly to scroll down
options.
Use the (-) and (+) buttons on monitor to increase or
decrease values. Brightness, Contrast, and Color,
displayed on screen. Brightness, Contrast, and Color
have a value of 1-100 that come factory-set at 50, the mid-
range. Reset will restore the factory settings.
2 Menu Screen: VOLUME (Due to no audio on camera
this funtion has been disengaged.)
BRIGHT 50
CONTRAST 50
COLOR 50
RESET
PICTURE
PICTURE

3 PICTURE: Picture refers to picture delay. This
determines how long a camera stays on past the trigger
wire being deactivated (powered). This allows for using
the turn signal flasher wire as a trigger.
4 SYSTEM: LANGAUGE The default language is
English. There are 7 options: English, Chinese, French,
Deutsch, Italian, Spanish, and Portuguese. Source
selects the default camera. Guide lines will turn off/on
guide lines for a channel with a trigger wire connected.
5 PRESET: Sleep delays the camera function. Should
always stay set to ZERO. AV1, AV2, AV3 allows for
turning off unused channels.
CAMERA1 00S
CAMERA2 00S
CAMERA3 00S
LANG ENGLISH
SOURCE AV2
GUIDE LINES OFF
PICTURE
PICTURE
SYSTEMS:
PICTURE
SLEEP 0
AV1 ON
AV2 ON
AV3 ON
PRESET:
PICTURE

DVR OPERATIONS REMOTE