Comra Delta User manual

COMRA DELTA DEVICE QUICK START GUIDE
ENG, REV 1.1

Thank you for your purchase of the coMra Delta
– A safe, non-toxic and non-invasive solution to
serious pain, chronic illness and cellular regeneration.
This quick start guide contains everything you need
to get started using your device.
Our comprehensive coMra user guide contains
detailed instructions for treating over 200 conditions,
and can be found on the USB ash drive that came
with your coMra Delta set, or as a free download on
our website: comra-therapy.com/downloads
We wish you health and happiness on your
coMra journey!

1
2 3
4
5
6
(UNDERSIDE)
1
3
2
4
5
6
UNDERSIDE
STEP 1: GET FAMILIAR WITH THE LAYOUT AND
TECHNICAL SPECIFICATIONS OF YOUR COMRA
DELTA DEVICE
Hand Device Laser Class: IIa
Software version: 3.0
CE certication: 1023
1Start button
2Frequency select button
3Time select button
4Display area LEDs
5 Ultrasound on/o button
6Terminal eject button
Power
Input: 5V --- 500 mA
High power USB port
compatible
Electrical and operating
Requirements
Line voltage: 100V to 240V AC
Frequency: 50Hz to 60Hz
Operating temp: -5° to 50° C
Size and weight
Size: 151.5 x 51.5 x 34.5 mm
USB cable length: 195 cm
Weight: 80
1
2 3
4
5
6
(UNDERSIDE)
1
3
2
4
5
6
UNDERSIDE
Medical Terminal 1Infrared laser Wavelength: 980nm or
905nm / Optical Power (max): 10mW
2Ultrasound Frequency: 40kHz /
Pressure Level (max): 0dB at contact,
-30dB at 30cm
3Colour LEDs Wavelength: Red 650
nm, Indigo Violet 420 nm, Yellow/
Green 570 nm
Intensity: Red 300 mcd, Indigo Violet
240 mcd, Yellow/Green 240 mcd
4Magnets – Strength (max): 100 mT
Aesthetic Terminal 1Infrared laser Wavelength: 980nm
or 905nm, Optical Power (max):
10mW
2Ultrasound
Frequency: 40kHz
Pressure Level (max): 0dB at contact,
-30dB at 30cm
3Colour LEDs
Wavelength: Red 650 nm, Indigo
Violet 420 nm, Yellow/Green 570 nm
Intensity: Red 300 mcd, Indigo Violet
240 mcd, Yellow/Green 240 mcd
4Magnets – Strength (max): 100 mT
Probe Terminal 1Infrared laser
Wavelength: 980nm or 905nm,
Optical Power (max): 10mW
3Colour LEDs
Wavelength: Red 650 nm, Indigo
Violet 420 nm, Yellow/Green 570 nm
Intensity: Red 300 mcd, Indigo Violet
240 mcd, Yellow/Green 240 mcd
4Magnets – Strength (max): 100 mT
5Sheaths – Strength (max): 100 mT

STEP 2: CHARGE THE DELTA POWER BANK
The included Delta Power Bank is shipped with a
storage charge only. You must fully charge the
Delta Power Bank before rst use.
To charge the Delta Power Bank plug the micro end
of the USB cable into the micro USB port at the side
of your Delta Power Bank, and the other end into any
powered USB port (computer, laptop, etc.), or a mains
electrical socket (using a suitable adaptor).
You need a minimum output of 5V 1A to charge the
Delta Power Bank.
4hrs
www
Once plugged into a power outlet, the four blue
indicating lights will power-up within a few seconds.
The lights ash on/o to indicate the Delta Power Bank
is charging.
4hrs
www
It will take up to 4-5 hours to fully charge your Delta
Power Bank. See the chart below for the indication
reference:
75% – 100%
50% – 75%
25% – 50%
5% – 25%
Off
The Delta Power Bank must charge for no less
than four hours, uninterupted, before rst use.

After you have completed the initial four hour charge
the Delta Power Bank is ready for operation.
4hrs
www
Failure to do this initial charge may reduce the
Delta Power Bank battery life.
STEP 3: GET YOUR COMRA USER GUIDE READY
Every coMra Delta set includes a USB ash drive
containing a printable PDF version of the coMra user
guide, with detailed instructions for treating over 200
conditions.
However, we recommend that you check for the
latest version of the coMra user guide here:
4hrs
www
https://comra-therapy.com/downloads
You can also download the coMra user guide as a
fully searchable and easy to use mobile app for Apple
iOS and Android.
Alternatively, you can browse the coMra user guide
web app here:
4hrs
www
https://ug.comra-therapy.com

STEP 4: POWER-UP YOUR COMRA DELTA DEVICE
Please read the ‘IMPORTANT’ information in the
coMra user guide, before using your coMra Delta
device for the rst time.
Once you have downloaded the coMra user guide
to your smart phone, tablet or computer, follow the
instructions on the app (or search the index on the
PDF version) to select a treatment protocol.
TREATMENTS
Enter dis-ease, condition or keyword
FOREWORD
BEFORE YOU START
OPERATING INSTRUCTIONS
COHERENT MULT I-R A D I A N C E S
Using the coMra Delta from the Delta Power Bank
First insert a Terminal into the Hand Device.
4hrs
www
Open the dust cover on top of the Delta Power Bank,
and plug the Hand Device USB power cord into the
Delta Power Bank’s USB port.
4hrs
www
Once plugged in the indicating lights on the Delta

Power Bank will activate, and the Start
Start 2 mins 1 min End
button
on the Hand Device will come on at half-power. The
device is now in Standby Mode.
4hrs
www
After 30 seconds of inactivity, the Delta Power
Bank will switch o automatically. If this happens,
unplug the Hand Device from the Delta Power Bank,
wait 5 seconds, and then plug it back in to operate
your coMra Delta device. If you try to plug the
Hand Device into the Delta Power Bank before the
5 second reset pause, the indicating lights will not
activate and the Delta Power Bank will not power-
up the coMra Delta device.
Note: In place of the Delta Power Bank, you can use any
other power bank/battery with a suitable output.
Using the coMra Delta from a mains outlet
First, insert a Terminal into the Hand Device.
4hrs
www
Then plug the USB end of the cable into the included
electrical adaptor and plug into a mains electrical
socket.
4hrs
www

Once plugged in, the Start
Start 2 mins 1 min End
button on the Hand
Device will come on at half-power. The device is now
in Standby Mode.
4hrs
www
STEP 5: APPLY YOUR CHOSEN PROTOCOL
When rst plugged in only the Start
Start 2 mins 1 min End
button light
will come on at half-power to show that your device is
in Standby Mode.
When the Start
Start 2 mins 1 min End
button is pressed and held for two
seconds, the device will power-up into Normal Ready
State. The lights on the Frequency
Start 2 mins 1 min End
and Time
Start 2 mins 1 min End
button will activate.
2
sec

Consult the coMra user guide for the correct
frequency and time selection of your chosen protocol.
Click down on the left side of the hinged button to
cycle through Frequency
Start 2 mins 1 min End
, and on the right side to
cycle through Time
Start 2 mins 1 min End
.
Variable (V)
1000 Hz
50 Hz
5 Hz
10 mins
5 mins
2 mins
1 min
PROTOCOL POINT
START/STOP FREQUENCYTIME U LTRASOUND U LTRASOUND (OFF) EJECT
mins
S T ART/STOP FREQUENCYTIME U LT RASOUND
Hz
1Top of sternum 1 50
If the treatment protocol requires you to use
ultrasound, click on the Ultrasound
Start 2 mins 1 min End
button to
switch on/o respectively.
TREATMENT POINT
START/STOP FREQUENCYTIME U LTRASOUND U LTRASOUND (OFF) EJECT
mins
S T ART/STOP FREQUENCYTIME U LT RASOUND
Hz
1Temple (both sides) 1 50
On Off
Note: Ultrasound is available only on the Medical and
Aesthetic Terminals of the coMra Delta series devices.
For information about using the ultrasound
option on your coMra Delta device, please read
‘General notes’ in the, ‘Before You Start’ section of
the coMra user guide.
When you are ready to start the protocol, place
the Terminal of your coMra Delta device over the
protocol point, using the middle of the Terminal
as the centre point. The Terminal must be in direct
contact with the surface of the skin.
Variable (V)
1000 Hz
50 Hz
5 Hz
10 mins
5 mins
2 mins
1 min
PROTOCOL POINT
START/STOP FREQUENCYTIME U LTRASOUND U LTRASOUND (OFF) EJECT
mins
S T ART/STOP FREQUENCYTIME U LT RASOUND
Hz
1Top of sternum 1 50
Press the Start
Start 2 mins 1 min End
button to begin the program. The
sounder will beep and the Start
Start 2 mins 1 min End
button will light up
and pulsate, indicating that the program is running.

ULTRASOUND (OFF) EJECT
x1
If you need to pause the program for any reason,
press the Start
Start 2 mins 1 min End
button once. The Start
Start 2 mins 1 min End
button
will ash on/o to indicate the program has paused.
x1
2
sec
x2
2
sec
x2
x1
To continue on from pause, press the Start
Start 2 mins 1 min End
button
once again.
x1
2
sec
x2
2
sec
x2
x1
When the selected time ends, two beeps will sound
indicating the end of the program.
Repeat the process for all the points on the protocol.
To stop the program while the program is running,
press and hold the Start
Start 2 mins 1 min End
button for two seconds.
Two beeps will sound indicating the end of the
program.
x1
2
sec
x2
2
sec
x2
x1
Frequency and Time display
There are four indicating LEDs for the Frequency
setting (hertz) and four indicating LEDs for the Time
setting (minutes).

Once a program has started, the in-built timer will
count-down and display the remaining minutes
left for the program. When nished, two beeps will
sound and the time indication will revert back to the
selected start time.
Start 2 mins 1 min End
When you have completed your protocol, and
nished using your coMra Delta device, press and
hold the Start
Start 2 mins 1 min End
button for two seconds. Two
beeps will sound, and the light will power-down to
half-power indicating the that the coMra Delta is in
Standby Mode.
x1
2
sec
x2
2
sec
x2
x1
STEP 7: CARE FOR YOUR COMRA DELTA DEVICE
Removing a Terminal from the Hand Device
Press and hold the Terminal eject button
Start 2 mins 1 min End
located
on the underside of the Hand device, and pull the
Terminal out of the Hand device.
4hrs
www
If you have a coMra Delta set, ensure to replace the
Terminal and Hand Device back inside the included
holdall to protect your investment.
Cleaning your coMra Delta device
Use a 3% solution of hydrogen peroxide or colloidal
silver to disinfecting and clean your coMra Delta Hand
Device and Terminals.
Do not use alchohol for cleaning.

Periodically check the infrared laser
We recommend you follow this easy step to ensure
the infrared laser in your Terminal/s work correctly.
You will need a digital camera such as those found
on most mobile phones and laptops. High quality
DSLR cameras will NOT work for this procedure,
because they are made with in-built infrared lters.
With a Terminal attached to your Hand Device, select
a 1 min (
Start 2 mins 1 min End
) program on Varible (V) Frequency (
Start 2 mins 1 min End
),
point the infrared laser at the camera lens and press
Start
Start 2 mins 1 min End
. NEVER look directly into infrared lasers
with the eyes!
4hrs
www
Your camera view screen should show the infrared
light as visible, thus conrming correct operation.
Note: depending on the quality of your camera, it should
be able to detect the three dierent pulse speeds of the
Variable frequencies; 5 Hz, 50 Hz and 1000 Hz.
STEP 8: REGISTER YOUR COMRA DELTA DEVICE
TO ACTIVATE YOUR 18 MONTH WARRANTY
By this warranty, Radiant Life Technologies®
guarantees this product to be free from defects
in design, material and workmanship at the time
of its original purchase by a consumer and for a
subsequent period of 18 months. This guarantee
does not cover damage or defects caused by misuse
or by failure to comply with the product’s user guide.
x1
x1
2
sec
x2
x1
www.comra-delta.com/register

COMRA DELTA CUSTOMER SUPPORT
[email protected]
www.comra-delta.com
© Radiant Life Technologies. All rights reserved.
coMra is a registered trademark of Radiant Life Technologies LTD.
Life-changing solutions by
Radiant Life Technologies
®