Concept Pro AIR2024-AHD Series User manual

AIR2024-AHD Range
Weatherproof Colour/Mono IR Camera
USER MANUAL

CAUTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Installation should be made by a qualified service person and should adhere to all local
codes.
In order to prevent electric shock and avoid damage to waterproof seals, do not loosen
any screws on the camera body.
Adjust the sunshield to avoid exposing the lens to direct sunlight.
Do not touch the front glass. If necessary, use a soft cloth to wipe off dust or debris.
Do not install on a surface subjected to frequent vibration or shocks.
Do not operate the camera beyond its temperature range or power ratings.
Should any damage or suspected damage occur, shutdown and disconnect the power and
contact your service provider.
Do not install the camera under unstable lighting conditions. Severe lighting change or
flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
Do not disassemble the camera.
Do not drop the camera or subject the unit to physical shocks
Do not point the camera directly at strong light, this can damage the sensor.
Ensure all removable covers are replaced to protect the inner components.
Do not install near devices which emit a strong electro-magnetic field.
Use a dry or damp cloth only for cleaning.
Note: Changes or modifications not expressly approved by the manufacturer can
cause the camera to be damaged and become inoperable. This may invalidate the
user warranty.
PLEASE FOLLOW THE ABOVE PRECAUTIONS – FAILURE TO DO SO MAY
INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.

The Concept Pro AIR20 Range is a weatherproof IR camera, suitable for
monitoring areas in hostile conditions and in low light.
PACKING CONTENTS
1Fixing Bolt for Sunvisor
2Photo Sensor
5Mounting Bracket
6Tri- Axis Points
4Sunvisor
712V DC Connector3IR LED
8Video Out Connector
2
3
1
4 5
7
68
SCREW
X3
ALLEN KEY
X1
MOUNTING
DRAWING PAPER
X1
USER
MANUAL
X1
USER MANUAL
PLASTIC-WALL PLUG
X3

INSTALLATION
Important: Ensure all precautions are observed during installation.
It is recommended the camera is tested during the most demanding environmental conditions
such as low light or bright sunlight to ensure continuity of effective CCTV monitoring. You may
find the use of an ND filter helpful.
lUse the supplied mounting template to mark the spacing for drilling.
lFollowing drilling, securely attach the bracket and camera to the wall.
Remove the camera unit carefully from the box,and keep the accessories in a safe place.
FIXING TO A WALL
DRAWING TEMPLATE
CONNECTION
l
l
l
Connect the video output to your monitor.
Check the power supply is correct and
connect it to the power port on the Camera.
View the picture on your monitor to check
the power and video connections are
working properly.
l
l
To assist in installation when using an
analogue test monitor, the camera can be
switched to an analogue output by pushing
the joystick fully up for several seconds.
The camera can be returned to AHD output
by pushing the joystick fully left for several
seconds.
PSU
Troubleshooting
lEnsure all connections to the Camera and DVR / Monitor are correct.
lIf a picture still cannot be obtained please contact your supplier for technical support.

POSITIONING
1
2
1
Point the Camera towards the area to be monitored.
2b
2a

UP
LEFT RIGHT
DOWN
MENU / ENTER
Shift the button UP for 5
seconds. This will switch to
a 960H ready output.
Shift the button to the LEFT
for 5 seconds. This will
switch to the 1080p AHD
output.
Please note: The 4-in-1 variant AHD cameras will come with a yellow
label on the cable loom explaining the direction of the switch.
Shift LEFT for 5 seconds to switch the camera to AHD.
Shift RIGHT for 5 seconds to switch the camera to TVI.
Shift UP for 5 seconds to switch the camera to CVBS or Analogue.
Shift DOWN for 5 seconds to switch the camera to CVI.
2MP cameras will be set to AHD by default. 3MP cameras will be set
to TVI by default.
OSD Controller
ON SCREEN DISPLAY (OSD)

MAIN MENU
AE
WB
DAY-NIGHT
VIDEO SETTING
LANGUAGE:
RESET
SAVE-EXIT
EXIT
⏎
⏎
⏎
⏎
ENGLISH, CHINESE, SPANISH, KOREAN, ITALIAN
⏎
⏎
VIDEO SETTING
CONTRAST:
SHARPNESS:
COLOR GAIN:
DNR:
IMAGE SIZE:
FORMAT:
RETURN
1-50
1-20
1-20
1-15
1080P, 720P
PAL, NTSC
⏎
DAY / NIGHT
MODE:
RETURN
EXT, AUTO, COLOR, B/W
⏎
EXPOSURE
BRIGHTNESS:
EXPOSURE MODE:
LV (EXPOSURE
MODE = BLC):
GAIN:
RETURN
1-20
GLOBE, CENTER, BLC, FLC
1-8
⏎
0-8
MODE:
RGAIN
(MODE = MWB):
BGAIN
(MODE = MWB):
RETURN
ATW, MWB
⏎
1-16
1-16
WB

MODEL
IMAGE SENSOR
SIGNAL SYSTEM
MIN. ILLUMINATION
S/N RATIO
DAY & NIGHT
SHUTTER SPEED
WIDE DYNAMIC RANGE
DIGITAL NOISE REDUCTION
LENS
FIELD OF VISION
IR LED
IR RANGE
IR WAVELENGTH
EFFECTIVE RESOLUTION
FRAME
WHITE BALANCE
GAIN
LIGHT COMPENSATION
MAX DISTANCE
OUTPUT INTERFACE
POWER SUPPLY
POWER CONSUMPTION
OPERATING TEMPERATURE
OPERATING HUMIDITY
INGRESS PROTECTION
APPROVALS
MATERIAL
PRODUCT DIMENSIONS
PRODUCT WEIGHT
AIR2024-AHD/2.8 AIR2024-AHD/6
2.8mm Fixed
89°
6mm Fixed
60°
12mm Fixed
35°
1/2.8”Sony CMOS
PAL/NTSC
0.001Lux @ (F1.2,AGC ON),0 Lux with IR
≥50dB
ICR
PAL:1/50-1/50000, NTSC:1/60-1/60000
dWDR
2D/3D
2pcs
20m
850nm
1920x1080
PAL:25fps ,NTSC:30fps
Auto
Auto
Auto
75-5 300m
AHD (TVI/CVBS optional)
12VDC
0.72W(IR LED off) 3.72W(IR LED on)
-10℃~+55℃
0% - 85% RH
IP66
CE / FCC
Aluminium Alloy
φma x81mm × 200mm
470g
AIR2024-AHD/12
SPECIFICATION

DIMENSIONS

NOTES

NOTES

OCTOBER 17 Design and specification are subject to change without notice.