Concept Pro AIR3526-AHD User manual

AIR3526-AHD
AIR3526-AHD -Z
Weatherproof Colour/Mono IR Camera
USER MANUAL

CAUTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Installation should be made by a qualified service person and should adhere to all local
codes.
In order to prevent electric shock and avoid damage to waterproof seals, do not loosen
any screws on the camera body.
Adjust the sunshield to avoid exposing the lens to direct sunlight.
Do not touch the front glass. If necessary, use a soft cloth to wipe off dust or debris.
Do not install on a surface subjected to frequent vibration or shocks.
Do not operate the camera beyond its temperature range or power ratings.
Should any damage or suspected damage occur, shutdown and disconnect the power and
contact your service provider.
Do not install the camera under unstable lighting conditions. Severe lighting change or
flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
Do not disassemble the camera.
Do not drop the camera or subject the unit to physical shocks
Do not point the camera directly at strong light, this can damage the sensor.
Ensure all removable covers are replaced to protect the inner components.
Do not install near devices which emit a strong electro-magnetic field.
Use a dry or damp cloth only for cleaning.
Note: Changes or modifications not expressly approved by the manufacturer can
cause the camera to be damaged and become inoperable. This may invalidate the
user warranty.
PLEASE FOLLOW THE ABOVE PRECAUTIONS – FAILURE TO DO SO MAY
INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.

The Concept Pro AIR35 Range is a weatherproof IR camera, suitable for
monitoring areas in hostile conditions and in low light.
1Fixing Bolt for Sunvisor
2Photo Sensor
6Tri- Axis Points
712V DC Connector
4Sunvisor
8Video Out Connector3IR LED
9External Lens
Adjustment
5Mounting Bracket
4 5
7
68
2
3
19
PACKING CONTENTS
SCREW
X3
USER
MANUAL
X1
ALLEN KEY
X1
MOUNTING
DRAWING PAPER
X1
USER MANUAL
PLASTIC-WALL PLUG
X3

INSTALLATION
Troubleshooting
lEnsure all connections to the Camera and DVR / Monitor are correct.
lIf a picture still cannot be obtained please contact your supplier for technical support.
lUse the supplied mounting template to mark the spacing for drilling.
lFollowing drilling, securely attach the bracket and camera to the wall.
FIXING TO A WALL
DRAWING TEMPLATE
Important: Ensure all precautions are observed during installation.
It is recommended the camera is tested during the most demanding environmental conditions
such as low light or bright sunlight to ensure continuity of effective CCTV monitoring. You may
find the use of an ND filter helpful.
Remove the camera unit carefully from the box,and keep the accessories in a safe place.
CONNECTION PSU
l
l
l
Connect the video output to your monitor.
Check the power supply is correct and
connect it to the power port on the Camera.
View the picture on your monitor to check
the power and video connections are
working properly.
l
l
To assist in installation when using an
analogue test monitor, the camera can be
switched to an analogue output by pushing
the joystick fully up for several seconds.
The camera output type can be selected
with the OSD buttons by pressing in the
direction of the desired output type for
several seconds.
Power Input
Video Output

POSITIONING
1
2
1
Point the Camera towards the area to be monitored.
2b
2a

OSD Controller
ON SCREEN DISPLAY (OSD)
Enter the service hatch on the underside of the camera via the 2 hex screws.
Locate the small joystick menu button. The directions are marked on the chassis.
Press and hold LEFT for 5 seconds to switch the camera to AHD.
Press and hold RIGHT for 5 seconds to switch the camera to TVI.
Press and hold UP for 5 seconds to switch the camera to CVBS or Analogue.
Press and hold DOWN for 5 seconds to switch the camera to CVI.
2MP cameras will be set to AHD by default. 3MP cameras will be set to TVI by default.
EXTERNAL LENS ADJUSTMENTEXTERNAL LENS ADJUSTMENT
2
1
3
B A
A
B
1
2
3
Open the lens adjuster cover and
adjust focus and zoom. Loose the
screw on the lens adjuster cover.
Lens Adjustment Tool
Focus and Zoom Adjustments
A
B
Zoom
Turn clockwise to zoom wide
anti-clockwise to zoom narrow
Focus
Turn clockwise to focus far
Anti-clockwise to focus near
UP
LEFT
RIGHT
DOWN MENU / ENTER
Press and hold UP for 5
seconds. This will switch to
a 960H ready output.
Press and hold LEFT for 5
seconds. This will switch to
the 1080p AHD output.

MAIN MENU
AE
WB
DAY-NIGHT
VIDEO SETTING
LANGUAGE:
RESET
SAVE-EXIT
EXIT
⏎
⏎
⏎
⏎
ENGLISH, CHINESE, SPANISH, KOREAN, ITALIAN
⏎
⏎
EXPOSURE
BRIGHTNESS:
EXPOSURE MODE:
LV (EXPOSURE
MODE = BLC):
GAIN:
RETURN
1-20
GLOBE, CENTER, BLC, FLC
1-8
⏎
0-8
VIDEO SETTING
CONTRAST:
SHARPNESS:
COLOR GAIN:
DNR:
IMAGE SIZE:
FORMAT:
RETURN
1-50
1-20
1-20
1-15
1080P, 720P
PAL, NTSC
⏎
DAY / NIGHT
MODE:
RETURN
EXT, AUTO, COLOR, B/W
⏎
MODE:
RGAIN
(MODE = MWB):
BGAIN
(MODE = MWB):
RETURN
ATW, MWB
⏎
1-16
1-16
WB
ON SCREEN DISPLAY (OSD)

SPECIFICATION
MODEL
IMAGE SENSOR
SIGNAL SYSTEM
MIN. ILLUMINATION
S/N RATIO
DAY & NIGHT
SHUTTER SPEED
WIDE DYNAMIC RANGE
DIGITAL NOISE REDUCTION
LENS
FIELD OF VIEW
IR LED
IR RANGE
IR WAVELENGTH
EFFECTIVE RESOLUTION
FRAME
WHITE BALANCE
GAIN
LIGHT COMPENSATION
MAX DISTANCE
OUTPUT INTERFACE
POWER SUPPLY
POWER CONSUMPTION
OPERATING TEMPERATURE
OPERATING HUMIDITY
INGRESS PROTECTION
APPROVALS
MATERIAL
PRODUCT DIMENSIONS
PRODUCT WEIGHT
1/21/2.8”Sony CMOS
PAL/NTSC
0.001Lux @ (F1.2,AGC ON),0 Lux with IR
≥50dB
ICR
PAL:1/50-1/50000, NTSC:1/60-1/60000
dWDR
2D/3D
89° to 35°
4pcs
35m
850nm
1920x1080
PAL:25fps ,NTSC:30fps
Auto
Auto
Auto
75-5 300m
AHD (TVI/CVBS optional)
12VDC
0.84W(IR LED off) 5.64W(IR LED on)
-10℃~+55℃
0% - 85% RH
IP66
CE / FCC
Aluminium Alloy
φmax 93mm x 250mm
680g
AIR3526-AHD AIR3526-AHD-Z
2.8 - 12mm Varifocal Lens 2.8-12mm Motorized Zoom Lens

DIMENSIONS
93mm
250mm

NOTES

NOTES

OCTOBER 17 Design and specification are subject to change without notice.