CONCORD Decca 60DEC3EST Operating instructions

A Continuing Commitment to Excellence
Part Number: 60DEC3EST
Owners Manual
and
Installation Instructions
60DEC (17.6 LBS)
®Decca

2
READ AND SAVE THESE INSTRUCTIONS
Before beginning installation of your new Concord® ceiling fan,
read and follow these safety precautions. If you are not familiar
with national and local electrical codes and basic electrical wiring
procedures, we recommend that you have a qualified electrician
install your new ceiling fan.
Before you begin, TURN OFF THE ELECTRICITY. Determine which cir-
cuit your new fan will be using and remove the fuse or turn off the circuit
breaker at the main electrical panel.
Make sure that all wiring conforms to national and local electrical codes. If
you are in question, obtain a copy of the codes and wire the fan according-
ly. Never leave bare wires uncovered (wire connection), use wire nuts to
cap all connections. Plastic electrical tape is not recommended.
When working with electricity, never take short cuts. Follow the code in
every respect. Basic requirements for a ceiling fan installed with lights are,
120 volts AC - 60Hz, on a grounded circuit with a 15 amp breaker or fuse.
Make sure that your electrical system and choice of location meet these
requirements.
If the location where you plan to install your fan does not already have an
electrical outlet, hire a licensed electrician to run the wiring and install an
outlet box designed for ceiling fans or heavy fixtures. The outlet box
should be able to support a minimum moving weight of 50 pounds and
marked “Acceptable for Fan Support” (Plastic outlet boxes are not recom-
mended for ceiling fan installation).
If you plan to use an existing electrical location, check to make sure that the
outlet box is not PLASTIC, that it is securely attached and able to support
at least 50 pounds of moving weight and marked “Acceptable for Fan
Support”. If you have any questions, outlet boxes and support systems for
ceiling fans are available at most hardware and do-it-yourself centers. In
most cases, your
Concord® dealer will have all the necessary products
for the proper and safe installation of your ceiling fan.
The location you choose should have a minimum clearance of 20 inches
from any wall to the blade tip at any point in its rotation and a minimum of
7 feet from blade level to floor and 10 inches from the blades.

3
This ceiling fan was not designed for installation in any location where it
might be exposed to moisture or high humidity. Installation in this type of
location could be unsafe, will most likely damage the fan and its finish
.....and WILL VOID YOUR WARRANTY.
Every effort has been made to provide you with proper instructions for the
safe installation of this ceiling fan. You could however, encounter situa-
tions or problems not covered in this manual. Should this occur, please
refer to a do-it-yourself wiring handbook or hire a qualified electrician to
install your fan.
Never attach the blades to your ceiling fan before the fan body is properly
mounted on the ceiling.
Lubrication of your new ceiling fan is not necessary. The ball bearings have
been adequately charged with grease and permanently sealed at the factory
so that, under normal conditions, further attention is not necessary.
To reduce the risk of fire, electrical shock, or personal injury,
mount this fan to an outlet box marked “Acceptable for Fan
Support” and use the Mounting Screws provided with the outlet
box. CAUTION: Install the primary mounting means and use
only the hardware provided with the fan.
To reduce the risk of personal injury take care not to bend the
blade carriers. Be careful not to insert foreign objects into rotat-
ing fan blades.
The important safeguards and instructions appearing in this
manual are not meant to cover all possible conditions and situa-
tions that may occur. It must be understood that common sense,
caution and careful attention to detail are factors which cannot
be built into this product. These factors must be supplied by the
person or persons installing, caring for, and operating the unit.
Conforms to D.O.E. EPACT regulation.
Limited lifetime warranty applies to fan only.

4
Loosen the two canopy mounting screws on the down-
side face of the mounting bracket.Back them out about
halfway. Thiswillallow for easierinstallationoftheceil-
ing canopy later(see figure 1).
Install the mounting bracket onto the electrical junction
box in the ceiling using two machine screws, two wash-
ers and two lockwashers (see figure 2).
The mounting bracket has slotted holes to enable it to
move sideways for proper alignment.Make sure the
mounting bracket is centered over the electrical junction
box and that it is securelyattached (see figure 3).
NOMOVEMENTSHOULDOCCURBETWEENTHE
MOUNTINGBRACKETANDTHEELECTRICAL
JUNCTIONBOX.
Pull the electrical wires in the junction box down and
through the mounting bracket.
Step 1 Install Mounting Bracket
Fig. 1
Fig. 2
Fig. 3
Slotted Holes
Junction Box
Ceiling Canopy Mounting Screw
TURN OFF
the Electricity
BEFORE
proceeding!

5
If you are using an extended support rod, (longer
than the one supplied with your fan) remove the
half ball from the small support rod that came
with the fan and put it on the extended support
rod. Make sure to retighten the set screw and
insert the safety screw.
Black
White
Screw
Washer
Washer
Mounting
Ground
Bracket
Fig. 4
Attach the WHITE wire from the junction box to
the WHITE wire from the Fan unit.
Attach the BLACK wire from the junction box to
the BLACK wire from the Fan unit.
Now connect the GROUND wire from the mount-
ing bracket to the GROUND wire in the ceiling
junction box.
NOTE: Make sure and use wire nuts on these con-
nections. DO NOT USE PLASTIC TAPE.
Step 2 Install the Fan Unit (see figure 4)

6
Fig. 5
Loosen the set screws (2) in the support rod cou-
pler located on the top center of the motor hous-
ing (see figure 5) until the inside channel is clear.
Remove and save the safety pin from the cou-
pler.
Place the ceiling canopy face down (small end)
over the support rod coupler on the motor hous-
ing.
Slide canopy onto support rod.
Feed the electrical wires from the fan housing
through the support rod.
Thread the support rod into the support rod cou-
pler until the safety screw can be inserted
through the hole in both the rod and coupler.
Insert the safety screw through the hole in the
support rod coupler and support rod then tighten
firmly.
Insert the set screw in the coupler and tighten
firmly.
Step 3 Attach the support assembly
Set Screw
Safety Screw
Set Screw
Canopy
Support Rod Coupler
Fig. 6
Receiver
Unit
Mounting Bracket
Support Rod
Notice the half ball on the end of the support rod is
grooved down one side. This Keyway fits over the
small keywaypin on theinsideof themountingbrack-
et and keeps the ceiling fan from spinning on the
mounting bracket.
Lift the fan and place the half ball in the center of the
mountingbracket withthe keywaypininserted into the
keyway on the ball. Turn the fan left and right slightly
tomakesureitisseatedonthebracket withthekeyway
pinin the keyway (see figure 6).
Trim the lead wires, leaving about six inches of each
wire extending from the supportrod.
Step 4 Hanging the Fan Body

7
Fig. 8
Fig. 7
Mounting
Bracket
Canopy
Canopy Screws
Insert a fan blade into the slot on the face of the
blade carrier (see figure 8).
Place a fiber pad on each mounting screw and
insert the screw into the blade carrier and through
the blade. Tighten each screw securely.
Repeat this procedure for each of the four blades.
Step 6 Fan Blade Assembly
Lift the ceiling canopy up into place covering the
mounting bracket.
Push the canopy up so the screws come through the
mounting holes in the canopy. Rotate the canopy
slightly and tighten the screws (see figure 7).
Step 5 Install Ceiling Canopy

8
Fig. 10A Fig. 10B
Fig. 9
Motor
Bottom
Molex
Connecter
Blue
Black
Motor Cover
Motor Cover Screw
Glass metal cap
•For use with light:
Place bulb included with fan into the socket on
the light socket plate. Place glass cover on light
socket plate and rotate until secure (see figure
10A).
•For use without light:
Place solid metal cap onto light socket plate and
rotate until secure (see figure 10B).
Step 8 Install Bulb & Glass Cover,
or Optional Metal Cap
Remove and save 1 of the 3 screws from the bot-
tom of fan motor housing.
Place cover on housing lining up the 2 keyway
holes over the 2 remaining screws. Rotate cover,
locking screws into keyway holes. Replace screw
you removed earlier.
Tighten all 3 screws securely.
Step 7 Install Bottom Motor Cover(see figure 9)

9
Operation Instruction
NOTE: The Remote Control Transmitter comes
with a bracket that can be mounted in any con-
venient place you choose. Next to a light switch
in the same room as the ceiling fan is a good
place.
Remote Control Operation Instruction
Attach the bracket with the two screws provided.
Remove the panel on the back of the hand control
(transmitter)and install a 12 volt battery(included).
Replace the panel.
The Remote Control Transmitter
Transmitter
Mounting Bracket
Mounting Screw
®
I VI
V
IVIII
II
Mounting Screw
Cover Plate

10
RESETTING THE CODE WHEN USING DIMMING CONTROL
1. Turn off the AC Power for at least 30 seconds before switching it back on.
2. Press and hold the SET BUTTON for 6 seconds. NOTE: You must complete this process within 60 seconds of turning on the fan.
3. While the code pairing is in process, the fan operates at highest speed in REVERSE mode automatically for 90 seconds then,
operates in FORWARD mode for 90 seconds. The code pairing procedure is complete when fan motor stops.
RECEIVER POWER SURGE AND OBSTRUCTION PROTECTION
1. OBSTRUCTION LOCK POSITION: The Internal Receiver has a built-in safety against obstruction during operation. The
motor will turn off after 30 seconds if their is an obstruction. Once you remove the obstacles you will need to disable the power
supply to re-start the motor.
2. POWER SURGE: If the Internal Reciever detects the unit is receiving over 80 Watts the receiver will turn off the fan. To reset,
wait for 5 seconds and turn on the AC Power and restart the fan.
  (see figure 11A)
1. FAN SPEED CONTROL PAD: Controls six fan speeds from highest (VI) to lowest (I)
2. FAN ON/ OFF BUTTON: Turns fan motor On/Off
3. REVERSE BUTTON: Controls fan blade direction ( Clockwise Summer and Counter-Clockwise for Winter )
4. LIGHTING CONTROL BUTTON: Press to turn light on/off. Hold the button for dimming feature.
5. SET BUTTON: Perform the following steps to set remote code. (see figure 11B)
Step 1: Turn on the AC power after attaching the blades to the motor.
Step 2: Turn fan power on, press and hold SET button on back of remote for 5 seconds. The lamp blinks twice when
finishing setup. (NOTE: You must complete this Process within 60 seconds of turning on the fan)
Step 3: After the SET button is pressed, the fan will run on high speed (VI) until setup is finished. Once setup is completed
the fan will return to it’s original factory speed and will then be able to be controlled using the FAN SPEED CON-
TROL PAD BUTTONS.
D
ON
●N ECE
1 2 3 4
6
5
®
I VI
V
IVIII
II
D
ON
●N ECE
1 2 3 4 SET
12V
2
1
3
4
Fig. 11A Fig. 11B

11
Canopy Screw
Plate Screw (3)
Motor Coupler
Motor Cover Screw (3)
Bottom Light Plate
Light Glass Cap
Bulb
Blade To Motor Screw
Canopy
Safety Screw
Support Rod
Coupling Cap
Hanging Ball
metal cap
Set Screw
Set Screw
Blade
Maintenance
Your fan requires very littlemain-
tenance. Cleaning of thehousing
should be done with adamp soft
cloth, DO NOT USE CLEANING
AGENTS. Clean theblades with
a duster or dry cloth.Any moisture
could cause theblades to warp and
make the fanwobble while running.

12
©
®Concord Fans 2012
Concord Fans.
Concord Fans is a division of Luminance.
ATTENTION
Under the Energy Policy Act of 2005, federal regulations require
all ceiling fans with light kits manufactured or imported after
January 1, 2009, to limit the total wattage consumed by the light
kit to 190 watts.
Therefore, this product is equipped with a 190W limiting device. If
lamping exceeds 190 watts, the light kit will shut off automatically
until the proper wattage of bulbs are installed. Reset the light kit
by turning it off, replacing the bulbs with the correct wattage, and
then turning the light kit back on.
Conforms To D.O.E. EPACT Regulation
Limited Lifetime Warranty Applies To Fan Motor Only