Conker ST5 User manual

5” RUGGED ANDROID
SMARTPHONE
CONKER ST5

IT’S THIS RUGGED.
IP67 Rated
Drop Tested from 1.5 metres onto
concrete
Waterproof under a meter of water for 30
mins
Impervious to dust
Operating temperature between -20 °C
and 60 °C
YOUR BATTERY IS THIS GOOD.
4,000mAh battery
THE MEMORY IS THIS BIG.
2GB RAM + 16GB storage
THE CONNECTIVITY IS THIS GOOD.
1 x 3.5mm Headphone jack
1 x Micro USB (OTG)
1 x Micro SD card
1 x SIM slot
1 x Magnetic clasp charging port
Waterprood internal microphone and loud
speaker
THE CAMERA IS THIS COOL.
Up to 13 Megapixel rear camera
Up tp 5.0 Megapixel front camera
THE SIZE AND WEIGHT IS NO MORE THAN THIS.
Dimensions 165 x 82 x 14 mm
Weight 240g
YOUR NETWORK IS THIS CAPABLE
Wifi: 802.11 a/b/g/n
Bluetooth: 4.0
3G or 4G LTE
GPS
Supports tethering
Supports tethering and casting
DISPLAY IS THIS BRIGHT AND STRONG.
Display 5”IPS
Resolution 1280 x 720
Mulit-touch screen with Gorilla glass
Brightness 430 nits
THE OPERATING SYSTEM IS.
Android 5.1
THE SENSORS CAN TELL YOU THIS MUCH.
Accelerometer
Gyroscope
Ambient light
THE PROCESSOR IS THIS FAST.
MediaTek Quad-Core

HOW TO USE YOUR ST5 RUGGED DEVICE
1. Unused
2. Magnetic charging port
3. Reset Button
4. Micro USB port
5. Headphones
6. Front camera
7. Ear Piece
8. Light sensor/ notification
light
9. Menu button
10. Home button/ Long press for
recent apps
11. Back button
12. Volume up
13. Volume down
14. Power button
15. Lanyard port
16. Rear camera
17. Flash
PITR ESET
SIM

POWERING ON
To power on, press and hold the power
button for 3 seconds.
To power off, press and hold the power
button and select “Power Off” from the
menu that apears on the screen
BUTTON FUNCTIONS
Menu button: Show the available
menu in the current application.
Home Button: Returns to Home
screen. To view recent application
press and hold the button
Back button: Return to previous
screen
INSERTING SIM AND MICRO SD CARD
Always power off the device before
changing SIM or Micro SD memory
card
Remove the battery cover. Use the
supplied tool to rotate screws 1 & 2
anti-clockwise.
SIM
SIM
SIM
1
2
1
2
1. Micro SD memory card slot
2. SIM card slot
Always use the right size of SIM Card

MICRO
SD
INSERTING YOUR MICRO SD MEMORY
CARD
Slide the cover
down to release.
Then insert the Micro
SD card with gold con-
nectors facing down as
shown in this diagram. Close
cover slide up to lock.
When putting the back cover back on,
do not overtighten the screws
CHARGING YOUR PHONE
Your phone can be charged in two
ways, either using the magnetic charg-
ing port or by connecting a micro USB
cable. The easiest method is with the
magnetic charging cable.
The magnetic charging cable connects
to the magnetic charging port on the
left edge of your phone.
Alternatively you can charge your
phone using the micro USB port.
Connecting to a PC
To connect your device to a PC you
must first loosen the port cover at the
top of the phone.
The port cover remains connected to
your phone, please take care not to
pull it off completely.
INSTALLING HAND STRAP
You will find the following supplied in
the box.
Step 1
Using the Allen Key, remove screws
numbered 1, 2, 3 & 4 at the back of
the device.

Step 2
Using the Allen Key, remove screws
numbered 1, 2, 3 & 4 at the back of
the device.
Step 3
Use the supplied screws to attach the
strap to the device. Be careful not to
overtighten the screws.
SIM

To contact Conker Support:
01279 295830
[e-mail]
Conker
Calf Pens
Hatfield Park Farm
Takeley
CM22 6NG
Conker customers benefit from the UK’s market leader in rugged device
support. Contact us with complete confidence.
GET IN TOUCH

Thank you for purchasing a
CE Marking and European Economic Area
Tablet Technologies hereby declares that this equipment is in compliance with Direcve 2011/65/EU and 1999/5/EC or
2014/53/EU. The following standards have been applied and tested. Conformity is limited to the essenal requirements of the
R&TTE.
For your safety
To reduce the potenal risk of injury and or damage to equipment or property, always observe the following safety precauns.
WARNING
Do not aempt to repair or modify the product as this could cause harm and will void any warranty.
Do not expose your skin to the product or AC adaptor when using the product for prolonged periods.
Do not puncture the product or baery.
Use only the specied baery (supplied).
Use only the specied AC adaptor (supplied).
Ensure all port and interface covers are closed before exposing the product directly to water or elevated levels of moisture or dust.
Packaging and accessories are choking hazards and should be kept out of reach of children.
Do not operate the product while driving.
Do not expose the AC Adaptor to water and donot use Adaptor when faulty.
Prolonged use of headphones can lead to a loss of hearing.
CAUTION
Do not operate the product if it shows any visible signs of damage.
To prevent injury or harm, avoid looking directly at the ash or where applicable, the laser barcode scanner.
Do not expose the product to extreme temperatures for a prolonged period. Do not expose the product directly to your skin in extreme
temperature environments.
Baery
DANGER
The baery is for use solely with the specied product. Do not use it with any other products.
Do not use the baery if it becomes noceably damaged or deformed.
Do not crush, bend, deform, puncture, shred, throw, or apply high pressure to the baery.
Only charge the baery with the supplied charger or cradle.
Do not subject the baery to an open ame or expose it to excessive heat.
Contents can combust under pressure.
If the electrolyte from the baery comes into contact with the eyes, skin, or clothing, rinse thoroughly with cold water and seek medical
advice.

Baery Informaon
CAUTION. Use only approved baeries. Risk of explosion if baery is charged with an incompable charger, exposed to heat
>60C or replaced by an incorrect type.
European Baery Direcve 2006/66/EC
Dispose of baeries separately and responsibly. All waste baeries are classid as hazardous waste and should be disposed of
at a baery recycling centre.
Our rechargeable baery packs are designed and constructed to the highest standards within the industry. However, there are limitans
to how long a baery can operate or be stored before needing replacement. Many factors aect the actual life cycle of a baery pack, such
as heat, cold, harsh environmental condins and severe drops. Baeries are considered chemical products. As such, baery performance
will deteriorate over me if stored for a long period of me without being used. When baeries are stored over six (6) months, some
irreversible deterioran in overall baery quality may occur. Store baeries at half of full charge in a dry, cool place, removed from the
equipment to prevent loss of capacity, rusng of metallic parts and electrolyte leakage. When storing baeries for one year or longer, the
charge level should be veried at least once a year and charged to half of full charge.
Replace the baery when a signicant loss of run me is detected. Standard warranty period for all baeries is one year from order
fullment, regardless if included as part of a mobile computer with a longer warranty duran or ongoing maintenance contract. The cycle
life of baeries will vary according to the charge and discharge condins, the temperature and other usage condins. When used in
accordance with the IEC charge and discharge specicans the typical cycle life of a baery is between 300 and 400 cycles at room
temperature. Individual results may vary.
Lithium baeries do not suer from “baery memory” therefore you do not need to fully charge to 100% or fully discharge to 0%. Complete
discharge of baeries should always be avoided. Shallow discharge is preferable, i.e. recharge at 20% if possible.
Baery Safety Guidelines
The area in which the units are charged should be clear of debris and combusble materials or chemicals.
Improper baery use may result in a , explosion, or other hazard.
To charge the mobile device baery, the baery and charger temperatures must be between 0°C and +40°C (+32°F to +104°F).
Do not use incompable baeries and chargers. Use of an incompable baery or charger may present a risk of , explosion,
leakage, or other hazard. If you have any quesns about the compability of a baery or a charger, contact Tablet
Technologies support.
For devices that uize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF
logo or have completed the USB-IF compliance programme.
Do not disassemble or open, crush, bend or deform, puncture, or shred.
Severe impact fromdropping any baery-operated device on a hard surface could cause the baery to overheat.
Do not short circuit a baery or allow metallic or conducve objects to contact the baery terminals.
Do not modify or remanufacture, aempt to insert foreign objects into the baery, immerse or expose to water or other
liquids, or expose to , explosion, or other hazard.
Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or
other heat source.
Do not place baery into a microwave oven or dryer.
Baery usage by children should be supervised.
Please follow local regulans to promptly dispose of used re-chargeable baeries.
Do not dispose of baeries in .
Seek medical advice immediately if a baery has been swallowed.
In the event of a baery leak, donot allow the liquid to come in contact with the skin or eyes. If contact has been made, wash
the aected area with large amounts of water and seek medical advice immediately.
If you suspect damage to your equipment or baery, contact Tablet Technologies support to arrange for inspecn.
Class 2 Laser Product – Honeywell N4300 1D Laser Barcode Scanner
Safety Standards:
EN 60950-1:2005/Am1:2009,
IEC 60950-1:2006/A11:2009/A1:2010/A12:2011
Laser Safety Statement
This device has been tested in accordance with and complies with IEC 60825-1 ed2.0.
LASERLIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT,1.0 mW MAX OUTPUT: 650nm.
Engine Laser Beam:
Wavelength 650 nm
Max power output 1mW
The laser diode is considered an embedded laser. Intrabeam viewing of the laser shall beprevented.

Embedded Laser:
Wavelength 650 nm
Max power output 10 mW
Cau�on - use of controls or adjustments or performance of procedures other than those specified by the manufacturer may result in
hazardous radia�on exposure.